2013 Peugeot Expert VU Owner's Manual

12
7

Snow screen
QUICK HELP
7
REMOVABLE SNOW SCREEN

According to country, the removable snow
screen is installed on the lower part of the
front bumper to prevent the accumulation of
snow at the radiator cooling fan.
FITTING

- Offer up the snow screen facing its
centring pin A
on the front bumper.

- Put it in place by pressing at each clip B
located in the four corners.

Do not forget to remove the snow screen
when the exterior temperature is higher than
10°C (no risk of snowfall) and when towing.
REMOVAL

- Pass a screwdriver into the hole located near each of the clips.

- Use the screwdriver as a lever to unclip the four clips B
in turn.

6. REFITTING THE REPAIRED
WHEEL

The wheel is refitted as described in step 5,
not forgetting to refit the wheel trim.
Refer to the "Identification markings"
section of chapter 8 to locate the tyre
label.
The spare wheel is not designed to
be used over long distances. Have
the tightening of the bolts and the tyre
pressure checked by a PEUGEOT dealer or
a qualified workshop as soon as possible.
Also, have the original wheel repaired and
refitted by a PEUGEOT dealer or a qualified
workshop as soon as possible.

128
Snow chains
Snow chains

In wintry conditions, snow chains improve
traction as well as the behaviour of the
vehicle when braking. The snow chains must be fitted only to
the driving wheels. They must never be
fitted to "space-saver" type spare wheels.
Take account of the legislation in force
in your country on the use of snow
chains and the maximum running speed
authorised. Advice on installation
)
If you have to fit the chains during
a journey, stop the vehicle on a flat
surface on the side of the road.
)
Apply the parking brake and position any
wheel chocks to prevent movement of
your vehicle.
)
Fit the chains following the instructions
provided by the manufacturer.

)
Move off gently and drive for a few
moments, without exceeding 30 mph
(50 km/h).
)
Stop your vehicle and check that the
snow chains are correctly tightened.

Avoid driving on roads that have been
cleared of snow, to avoid damaging
your vehicle's tyres and the road surface. It
is recommended that before you leave, you
practise fitting the snow chains on a level
and dry surface. If your vehicle is fitted with
alloy wheels, check that no part of the chain
or its fixings is in contact with the wheel rim.
Use only the chains designed to be fitted to
the type of wheel fitted to your vehicle:
Original tyre size
Maximum link size.

215/65 R15

12 mm

215/60 R16
MICHELIN

215/60 R16
BRIDGESTONE

For more information on snow chains,
contact a PEUGEOT dealer or a qualified
workshop.

12
9

Changing a bulb
QUICK HELP
7

CHANGING A BULB

Type A

All glass bulb: pull
gently as it is fitted by
pressure.
Type B

Bayonet bulb: press
on the bulb then turn it
anticlockwise.
Type C

Halogen bulb: release
the retaining spring from
its housing.
TYPES OF BULB

Various types of bulb are installed on your vehicle. To remove them:
Halogen bulbs must be changed after
the headlamp has been off for several
minutes (risk of serious burns). Do not touch
the bulb directly with your fingers, use lint-
free cloths.
When each operation has been completed,
check the operation of the lighting.

130
Changing a bulb
3. Direction indicators
Type B , PY21W - 21W (amber)

- Turn the bulb holder a quarter turn anticlockwise.

- Remove the bulb by pressing it lightly while turning it anticlockwise.

- Change the bulb.

-
Ensure that the cover is refitted
correctly all the way round to ensure
sealing.
FRONT LAMPS

Open the bonnet. To access the bulbs, reach
behind the headlamp unit.
Carry out the operations in reverse order to
refit each bulb.
1. Dipped / Main beam headlamps
Type C , H4 - 55W

- Remove the centre cover by pulling the flexible rubber tab.

- Disconnect the electrical connector.
- Release the retaining spring.
- Change the bulb taking care to align the metal part with the slots in the
lamp. 2.
Sidelamps
Type A , W5W - 5W

- Remove the cover by pulling the flexible rubber tab.

- Remove the bulb holder fitted by pressure by pulling the connector.

- Change the bulb.
- Ensure that the cover is refitted
correctly all the way round to ensure
sealing. 4.
Foglamps
Type C , H1 - 55W

Contact a PEUGEOT dealer or a qualified
workshop.

131

Changing a bulb
QUICK HELP
7

DIRECTION INDICATOR SIDE
REPEATER
Type A , WY5W - 5W (amber)

- Push the repeater towards the rear and disengage it.

- Support the connector and turn the bulb holder a quarter turn to the left.

- Turn the bulb a quarter turn to the left, remove it and change it.

- When refitting, engage the repeater towards the rear and bring it towards the
front. Front / Rear


Amber coloured bulbs (direction indicators
and side repeaters) must be replaced with
bulbs of identical specification and colour.
COURTESY LAMPS

Type A , 12V 5W - 5W

- Unclip the lens by sliding a screwdriver in the slots on each side of the courtesy
lamp.
- Pull the bulb and change it.
- Clip the lens in its housing and ensure that it is secured correctly.

High pressure jet washing

When using this type of jet washer
on stubborn dirt, do not persist on the
headlamps, the lamps and their surrounds to
avoid damaging their coating and seals.

132
Changing a bulb

REAR LAMPS

For more information on bulbs, refer to the
"Types of bulb". - Identify the faulty bulb then open the
rear doors to 180°. Refer to the "Access"
section of chapter 2.
- Remove the two fixing nuts.
Pull the lens unit from the outside.
- Holding the lamp unit, disconnect the electrical connector.
- Move aside the 8 tabs then extract the
bulb holder.

- Remove the failed bulb by pressing it lightly while turning it anticlockwise.

- Change the bulb.

1.
Brake lamps / sidelamps
Type B , P21/5W - 21/5W

2. Direction indicators
Type B , PY21W - 21W (amber)

3. Reversing lamps
Type B , P21W - 21W

4. Foglamps
Type B , P21W - 21W
When refitting, take care to correctly
reposition:
- the 8 tabs,
- the two white lugs in the two rubber
holes to maintain the sealing of the lamp
unit,
- the supply wire to avoid trapping it.

133

Changing a bulb
QUICK HELP
7
THIRD BRAKE LAMP

Type A , W5W - 5W

NUMBER PLATE LAMPS

Type A , W5W - 5W

Lamp located on the inside (tailgate)
- Unscrew the two screws using a Torx
TM
20 screwdriver.

- Remove the plastic cover.
- Remove the bulb holder moving aside the two tabs.

- Remove the failed bulb by pressing it lightly while turning it anticlockwise.

- Change the bulb.

Type B
, P21W - 21W

With tailgate
- Move aside the plastic lens using a
screwdriver, on the point indicated by
the arrow.
- Change the bulb.
- Replace the plastic lens and press on it.

With hinged doors
- Unclip the interior trim.
- Disconnect the connector by moving aside its tab.

- Remove the plastic cover.
- Turn the bulb holder a quarter turn anticlockwise.

- Change the bulb. Lamp located on the outside (hinged doors)
- Unscrew the two screws using a Torx
TM
20 screwdriver.

- Remove the lamp.
- Change the bulb.
Type B
, P21W - 21W

Lamp on door top
- Remove the screws using an 8 mm
spanner.

- Remove the failed bulb by pressing it lightly while turning it anticlockwise.

- Change the bulb.

134
Changing a fuse

CHANGING A FUSE

The three fuseboxes are placed:
-
in the dashboard on the right-hand side (behind
the storage compartments, retractable),
- in the passenger compartment (battery
compartment),

- under the bonnet.
If fi tted on your vehicle, a further fusebox
is added for towing, the towbar and the
connections for the coachbuilder and platform
cab conversions. It is located on the right
behind the load retaining partition.
Removing and fitting a fuse

Before changing a fuse, the cause of the
fault must be found and rectified. Always replace a failed fuse with a fuse
of the same rating.

PEUGEOT will not accept responsibility
for the cost incurred in repairing your
vehicle or for rectifying the malfunctions
resulting from the installation of accessories
not supplied and not recommended by
PEUGEOT and not installed in accordance
with its instructions, in particular when
the combined consumption of all of the
additional equipment connected exceeds
10 milliamperes.
The descriptions communicated are only the
fuses which can be changed by the user.
For any other operations, go to a PEUGEOT
dealer or a qualified workshop.
For motor trade use: for complete
fuse and relay information, consult the
"Repair procedure" wiring diagrams via the
dealer network.