2013 MERCEDES-BENZ SL-Class display

The system behavior after accepting the
incoming call depends on your mobile phone.
R
The mobile phone supports the call waiting
function (via Bluetooth ®
) when:
the previously active call is held. You can
then switch back and forth between both
calls (toggling) (Y page 387).
R The mobile phone does not support the call
waiting function (via Bluetooth ®
) when:
the previously active call is ended.
This is also the case if you accept the
waiting call using the Voice Control System
(see the separate operating instructions).
The COMAND display changes. If you
continue to operate functions on the mobile
phone, the COMAND display may differ from
that of the mobile phone.
Making a further call
If the following conditions are met, you can
make a further call during an existing call:
R the function has to be supported by the
mobile phone network.
R the mobile phone has to support the
connection of a further call via Bluetooth ®
.
R the appropriate setting has to be activated
on the mobile phone.
If your mobile phone allows you to make a
second call via Bluetooth ®
, you can make
another while on the phone with someone
else. This action puts the previous call on
hold. The function is available. 0002
Symbol for making a second call X
Select symbol 0002by turning 003E0012003Fthe
COMAND controller and press 0039to
confirm.
or
X Press the 0017button on COMAND.
X Enter the phone number:
R
manually (Y page 384)
R using the phone book (Y page 389)
R using the call lists ( Ypage 392)
R using speed dial (Y page 385)
Call waiting
You can switch back and forth between calls
with this function. The function is available if
your mobile phone supports the toggling
function (via Bluetooth ®
).
You can use the function if you are answering
a second call or making a second call. Switching between the active call and the call
on hold
0002
Active call
0003 Call on hold
X Select symbol 0003and press 0039to confirm.
or
X Press the 0017button on COMAND or on
the multifunction steering wheel.
The previous call on hold is activated. Telephone
387COMAND Z

X
To end the active call: select0028in the
telephone basi cmenu and press 0039to
confirm.
or
X Press the 003Cbutton on COMAND or on
the multifunction steering wheel.
The call on hold is activated.
Conference call
You can interconnect calls (active and on
hold) on the mobile phone. This allows
numerous callers to hear and speak to each
other; see the mobile phone operating
instructions.
You can also make a further call in COMAND
(Y page 387). Using the phone book
Introduction The phone book displays the names and
phone numbers of all address book entries
saved in the COMAND address book. If an
address book entry does not have a
telephone number, it does not appear in the
phone book.
The phone book of the mobile phone is
automatically downloaded to COMAND after
connection.
In the telephone book, you can:
R
save phone numbers (Y page 390)
R search for entries (Y page 389)
R delete entries (Y page 390)
R import contact s(Ypage 403)
R delete contacts (Y page 404)
R receive vCards ( Ypage 404)
i The stored phone book and the vCards
remain in COMAND even if you use
COMAND with another mobile phone. The
entries can be viewed without a mobile
phone. For this reason, you should delete
any phone book entries before handing
over or selling the vehicle. Calling up the phone book Opening the phone book
X
Press the 0012function button.
X Select Name in the telephone basic menu
by turning 003E0012003Fthe COMAND controller
and press 0039to confirm.
If the phone book contains entries, they will
be displayed in alphabetical order. The
character bar at the bottom of the display
is active.
The character bar is used for fast selection
of an entry.
Enter the character using the character bar
(Y page 299). i
You can also call up the phone book using
the multifunction steering wheel; see the
separate vehicle Operator's Manual.
Closing the phone book
X Select the 0027symbol in the character bar
by sliding 000A0012and turning 003E0012003Fthe
COMAND controller and press 0039to
confirm.
or
X Press the 001Fback button. 388
TelephoneCOMAND

Phone book entry with several entries
X Select a sub-entry by turning 003E0012003Fand
press 0039to confirm.
X To return to the phone book using the
character bar: select0027in the list and
press 0039to confirm.
or
X Press the 001Fback button.
Displaying details for an entry X
Select an entry in the selection list by
turning 003E0012003Fthe COMAND controller.
X Select the list symbol to the right of the
entry by sliding 00120037the COMAND
controller and press 0039to confirm.
X Select Details and press
0039to confirm.
The detailed view appears.
X To close the detailed display: slide
003600120037 repeatedly until the entry is
highlighted again.
or
X Press the 001Fback button.
Deleting an entry from the phone book If the entry contains only phone numbers, it
is deleted from the phone book and address
book.
If it contains additional data, such as a
navigable destination, the entry is deleted in
the phone book. However, the entry is
retained in the address book. X
Select an entry in the selection list by
turning 003E0012003Fthe COMAND controller.
X Select the list symbol to the right of the
entry by sliding 00120037the COMAND
controller and press 0039to confirm.
X Select Delete and press
0039to confirm.
Ap rompt appears asking whethe rthe entry
should be deleted.
X Select Yes or
No and press
0039to confirm.
If you select Yes , the entry is deleted in
accordance with the rules described above.
If you select No , the process will be
canceled.
Creating anew entr yinthe phone book X
Slide 00380012the COMAND controller
repeatedly in the phone book until the
selection lis tappears.
X Select the list symbol on the right in the
selection list by sliding 00120037the COMAND
controller and press 0039to confirm.
X Select New Entry and press
0039to confirm.
X Select a category for the number, e.g.
Home , and press
0039to confirm.
X Select a category for the phone, e.g.
Mobile , and press
0039to confirm.
X Select Continue and press
0039to confirm.
The input menu with data fields appears. 390
TelephoneCOMAND

i
If no mobile phone is connected, then the
Call Lists menu item is grayed out and
cannot be selected. If you connect a mobile
phone other than the previous one to
COMAND, the previously available call lists
and their entries will be deleted
automatically. They are still available on the
mobile phone itself.
i You will only be able to select the
respective menu items once calls have
been received or dialed from COMAND.
Displaying missed calls in the COMAND
display is not supported by all mobile
phones.
Opening the call list and selecting an
entry X
Press the 0012function button.
X Select Call Lists in the telephone basic
menu by sliding 0012000Aand turning 003E0012003Fthe
COMAND controller and press 0039to
confirm.
Am enu appears.
X Select Calls Received or
Calls Dialed by turning
003E0012003Fand press 0039to
confirm.
The corresponding list appears.
i You can also call up the list of dialed calls
by pressing the 0017button when the
telephone basic menu is shown. In this
case, the list will only show phone
numbers.
X Select an entry by turning 003E0012003Fthe
COMAND controller.
X To dial a phone number: press0039.
X To close the list: select the0027symbol
and press 0039to confirm.
or
X Press the 001Fback button. Displaying details from a list entry COMAND can also show a shortened list entry
in full.
X Select a list entry by turning 003E0012003Fthe
COMAND controller.
X Select the list symbol to the right of the
entry by sliding 00120037the COMAND
controller and press 0039to confirm.
X Select Details and press
0039to confirm.
The detailed view appears.
X To go back to the list: slide003600120037
repeatedly until the list is highlighted.
Storing aphone number New address book entry
For incoming calls from a perso
nwho is not
in the address book, COMAND displays the
phone number in the call list. You can save
this entry.
X Open a call list and select an entry
(Y page 392).
X Select the list symbol to the right of the
entry by sliding 00120037the COMAND
controller and press 0039to confirm.
X Select Save and press
0039to confirm.
X Select New Entry and press
0039to confirm.
X Select a category for the number, e.g.
Home , and press
0039to confirm.
X Select a category for the phone, e.g.
Mobile , and press
0039to confirm. Number category Display (phone
book and address
book)
Not Classified No symbol
Home 0010
Work 000E392
TelephoneCOMAND

Telephone
category Display (phone
book and address
book)
Not Classified 0020
Mobile 000D
Car 0008
Pager 003A
X
Select Save and press
0039to confirm.
An input menu with data fields is shown.
The data field for the telephone numbe ris
filled in automatically. 0002
Data field with cursor
0003 Telephone numbe rand symbol for the
phone category (automaticall yentered)
0027 Characte rbar
Adding information to an address book
entry
For incoming calls from a person who is not
in the address book, COMAND displays the
phone number in the call list .You can save
this entry.
X Open a call list and select an entry
(Y page 392).
X Select the list symbol to the right of the
entry by sliding 00120037the COMAND
controller and press 0039to confirm.
X Select Save and press
0039to confirm. i
Save is shown in gray if the selected list
entry has already been saved.
X Select Add Phone No. and press
0039to
confirm.
X Select a category for the number, e.g.
Home , and press
0039to confirm.
X Select a category for the phone, e.g.
Mobile , and press
0039to confirm.
X Select Save .
The search menu for address book entries
appears.
X Search for the desired entry (Y page 389).
X Press 0039when you have finished searching.
COMAND stores the data if there are fewer
than five numbers assigned to the entry you
are searching for in the selected number
category.
You will see a message to this effect.
If five numbers are stored for the entry you
are searching for, a prompt will appear
asking whether you wish to overwrite one
of the existing numbers.
X Select Yes or
No and press
0039to confirm.
If you select Yes , a selection list with the
five existing numbers is displayed.
If you select No , the process will be
canceled.
X Select the number to be overwritten in the
list by turning 003E0012003Fthe COMAND controller
and press 0039to confirm.
COMAND overwrites the selected number
with the new data.
Deleting call lists If you are using a Bluetooth
®
phone that does
not support the PBAP Bluetooth ®
profile, the
call lists are generated and managed by
COMAND. You can delete these call lists in
COMAND.
If you download call lists from a Bluetooth ®
phone that supports the PBAP Bluetooth ®
profile, you cannot delete them from
COMAND. Telephone
393COMAND Z

X
Select Call Lists in the telephone basic
menu by turning 003E0012003Fthe COMAND
controlle rand press 0039to confirm.
X Select Delete Call Lists and press
0039
to confirm.
Ap rompt appears asking whethe ryou wish
to delete all call lists.
X Select Yes or
No and press
0039to confirm.
If you select Yes , the call lists are deleted.
If you select No , the process will be
canceled.
i If you delete these call lists from the
mobile phone (see the separate mobile
phone operating instructions), COMAND
updates the call list display the next time it
connects. Using the speed dial list
Storing an entry You can assign ten speed dial presets (0
–9)
to the speed dial list. There are two options
available for this purpose.
Option 1:
X Search for a phone book entry in the phone
book (Y page 389).
X If an entry has several phone numbers,
select the desired numbe rby turning
003E0012003F the COMAND controller.
X Selec tthe list symbol to the right of the
entry by sliding 00120037the COMAND
controller and press 0039to confirm.
Am enu appears.
X Select Speed Dial by turning
003E0012003Fthe
COMAND controller and press 0039to
confirm.
Am enu appears. Speed dial menu
X
Select Assign Speed Dial Preset and
press 0039to confirm.
The speed dial list appears. The selected
phone book entry is listed as the first entry.
The nexta vailable speed dial prese tis
highlighted. X
Select the speed dial preset by turning
003E0012003F the COMAND controller and press
0039 to confirm.
The phone book entry is saved in the speed
dial preset.
Option 2
X Call up the telephone basic menu
(Y page 383).
X Select Call Lists by sliding
0012000Aand
turning 003E0012003Fthe COMAND controller and
press 0039to confirm.
X Select Speed Dial Preset List and
press 0039to confirm.
The speed dial list appears. 394
TelephoneCOMAND

X
Select the list symbol to the right of the
entry by sliding 00120037the COMAND
controlle rand press 0039to confirm.
X Select Assign Speed Dial Preset and
press 0039to confirm.
The speed dial list appears. The selected
phone book entry is listed as the first entry.
The next available speed dial preset is
highlighted. X
Select the speed dial preset by turning
003E0012003F the COMAND controller and press
0039 to confirm.
The phone book entry is saved in the speed
dial preset.
Making a call via speed dial The speed dial list contains stored phone
book entries (Y page 394).
Option 1:
X Hold down one of the numbe rkeys for
longer than two seconds.
The telephone basic menu displays the
selected entry. This initiates dialing.
Option 2:
X Call up the telephone basic menu
(Y page 383).
X Select Call Lists by sliding
0012000Aand
turning 003E0012003Fthe COMAND controller and
press 0039to confirm.
The speed dial list appears. X
Select Speed Dial Preset List by
turning 003E0012003Fthe COMAND controller and
press 0039to confirm.
The speed dial list appears.
X Select preset and press 0039to confirm.
The telephone basic menu displays the
selected entry. This initiates dialing.
Deleting aspee ddial number X
To delete a speed dial number: select
Delete Speed Dial Preset in the Speed
dial menu by turning 003E0012003Fthe COMAND
controller and press 0039to confirm.
The speed dial numbe ris deleted.
X To delete all speed dial numbers: select
Delete All Speed Dial Presets in the
Speed dial menu by turning 003E0012003Fthe
COMAND controller and press 0039to
confirm.
You will be asked whether you want to
continue.
X Select Yes or
No and press
0039to confirm.
If you select Yes , all speed dial presets will
be deleted from the speed dial list.
If you select No , the process will be
canceled. Text messages
Information and requirements If the above conditions are met, new incoming
text messages appearint
he COMAND text
message inbox. In addition, a tone sounds
and the 0018symbol appears. The symbol is
no longer displayed once you have read the
text message. The úmail symbol is
displayed if the text message memory is full.
The symbol is no longer displayed once you
delete at least one text message.
i COMAND may not load all of the most
recent text messages:
This may occur in exceptional cases, for
example when using certain mobile Telephone
395COMAND Z

phones/brackets and if the mobile phone
inbox holds a large number of text
messages.
i In order to be able to use the text
message function, the Bluetooth ®
mobile
phone has to support Bluetooth ®
MAP
(Message AccessProfile).
Displaying the text message (SMS)
inbox Calling up the inbox
Text message (SMS) inbox
X
Press the 0012function button.
X Select Txt Msg. in the telephone basic
menu by turning 003E0012003Fthe COMAND
controller and press 0039to confirm.
The tex tmessage inbox appears.
Reading atext message (SMS)
X Call up the tex tmessage inbox
(Y page 396).
X Select a textm essage in the textm essage
inbox by turning 003E0012003Fthe COMAND
controller and press 0039to confirm.
The textm essage appears.
X To scroll through the display or select
phone numbers in atext message: turn
003E0012003F the COMAND controller.
The display scrolls up or down line by line,
or skips to the nex torprevious telephone
number and automatically highlights it.
X To return to the list: press0039and select
Back . Text message read-aloud function
Settings for the read-alou
dfunction:
R Language (Y page 306)
R Speed (Y page 305)
X Press 0039while a text message is being
displayed, select Read Aloud and press
0039 to confirm.
COMAND reads out the text message.
X To cancel the read-alou dfunction: press
the 001D button.
or
X Press 0039, select Cancel Read-Aloud Function and press
0039to confirm.
Sender or text display
You can switch between displaying the text
message sender or the text message content.
The sender display shows the sender of the
text message. If the sender is stored in the
COMAND phone book, the name is displayed.
The text display shows the first few words of
the text message.
X Select a text message in the text message
inbox by turning 003E0012003Fthe COMAND
controller.
X To switch to the text display: select the
lis ts ymbol to the right of the text message
by sliding 00120037the COMAND controller and
press 0039to confirm.
X Select Display Text and press
0039to
confirm.
The view changes.
X To switch to the sender display: select
the list symbol to the right of the text
message by sliding 00120037the COMAND
controller and press 0039to confirm.
X Select Display Sender and press
0039to
confirm.
The view changes.
X To return to the telephone basic menu:
press the 000Cbutton. 396
TelephoneCOMAND