2013 Lancia Voyager language

display the message “ Blind spot sys-
tem unavailable-Astronomy zone”.
The side mirrors LED’s will be lit up
and stay lit until the vehicle exits the
zone.
UCONNECT™ PHONE
(for versions/markets,
where provided)
NOTE: For Uconnect™ Phone
with Navigation or Multimedia ra-
dio, refer to the Navigation or Mul-
timedia radio's User's Manual
(separate booklet) Uconnect™
Phone section.
Uconnect™ Phone is a voice-
activated, hands-free, in-vehicle com-
munications system. Uconnect™
Phone allows you to dial a phone
number with your mobile phone* us-
ing simple voice commands (e.g.,
“Call”…“Jim”… “Work” or
“Dial”…“151-1234 -5555”). Your
mobile phone's audio is transmitted
through your vehicle's audio system;
the system will automatically mute
your radio when using the
Uconnect™ Phone.Uconnect™ Phone allows you to
transfer calls between the Uconnect™
Phone and your mobile phone as you
enter or exit your vehicle and enables
you to mute the Uconnect™ Phone's
microphone for private conversation.
The Uconnect™ Phone is driven
through your Bluetooth® “Hands-
Free profile” mobile phone.
Uconnect™ Phone features
Bluetooth® technology - the global
standard that enables different elec-
tronic devices to connect to each other
without wires or a docking station, so
Uconnect™ Phone works no matter
where you stow your mobile phone
(be it your purse, pocket, or brief-
case), as long as your phone is turned
on and has been paired to the vehicle's
Uconnect™ Phone. The Uconnect™
Phone allows up to seven mobile
phones to be linked to the system.
Only one linked (or paired) mobile
phone can be used with the
Uconnect™ Phone at a time. The
Uconnect™ Phone is available in
English, Dutch, French, German,
Italian or Spanish languages (as
equipped).
WARNING!
Any voice commanded system
should be used only in safe driving
conditions following all applicable
laws, including laws regarding
phone use. All attention should be
kept on the roadway ahead. Failure
to do so may result in a collision
causing serious injury or death.
Uconnect™ Phone Button The radio or steering wheel
controls will contain the
two control buttons
(Uconnect™ Phone
but-
ton and Voice Command
button)
that will enable you to access the sys-
tem. When you press the button you
will hear the word Uconnect™ fol-
lowed by a BEEP. The beep is your
signal to give a command.
Voice Command Button
Actual button location may
vary with radio. The indi-
vidual buttons are de-
scribed in the “Operation”
section.
84

Call By Saying A Name
 Press the
button to begin.
 After the “Ready” prompt and the following beep, say “Call.”
 The system will prompt you to say the name of the person you want to
call.
 After the “Ready” prompt and the following beep, say the name of the
person you want to call. For ex-
ample, you can say “John Doe”,
where John Doe is a previously
stored name entry in the
Uconnect™ Phonebook or down-
loaded phonebook. To learn how to
store a name in the phonebook ,
refer to “Add Names to Your
Uconnect™ Phonebook”.
 The Uconnect™ Phone will con- firm the name and then dial the
corresponding phone number,
which may appear in the display of
certain radios. Add Names To Your Uconnect™
Phonebook
NOTE: Adding names to the
Uconnect™ Phonebook is recom-
mended when the vehicle is not in
motion.
 Press the
button to begin.
 After the “Ready” prompt and the following beep, say “Phonebook
New Entry”.
 When prompted, say the name of the new entry. Use of long names
helps the Voice Command and it is
recommended. For example, say
“Robert Smith” or “Robert” in-
stead of “Bob”.
 When prompted, enter the number designation (e.g., “Home”,
“Work”, “Mobile”, or “Other”).
This will allow you to store multiple
numbers for each phonebook entry,
if desired.
 When prompted, recite the phone number for the phonebook entry
that you are adding. After you are finished adding an entry
into the phonebook, you will be given
the opportunity to add more phone
numbers to the current entry or to
return to the main menu.
The Uconnect™ Phone will allow you
to enter up to 32 names in the phone-
book with each name having up to
four associated phone numbers and
designations. Each language has a
separate 32-name phonebook acces-
sible only in that language. In addi-
tion, for versions/markets, where pro-
vided, and supported by your phone,
Uconnect™ Phone automatically
downloads your mobile phone’s
phonebook.
Phonebook Download —
Automatic Phonebook Transfer
From Mobile Phone
For versions/markets, where pro-
vided and specifically supported by
your phone, Uconnect™ Phone auto-
matically downloads names (text
names) and number entries from your
mobile phone’s phonebook. Specific
Bluetooth® Phones with Phone Book
87

 After the “Ready” prompt and thefollowing beep, say “Phonebook
Delete”.
 After you enter the Phonebook De- lete menu, you will then be asked
for the name of the entry that you
wish to delete. You can either say
the name of a phonebook entry that
you wish to delete or you can say
“List Names” to hear a list of the
entries in the phonebook from
which you choose. To select one of
the entries from the list, press the
button while the Uconnect™
Phone is playing the desired entry
and say “Delete”.
 After you enter the name, the Uconnect™ Phone will ask you
which designation you wish to de-
lete; home, work, mobile, other, or
all. Say the designation you wish to
delete.
 Note that only the phonebook entry in the current language is deleted.
 Automatic downloaded phonebook entries cannot be deleted or edited. Delete/Erase “All” Uconnect™
Phonebook Entries
 Press the
button to begin.
 After the “Ready” prompt and the following beep, say “Phonebook
Erase All”.
 The Uconnect™ Phone will ask you to verify that you wish to delete all
the entries from the phonebook.
 After confirmation, the phonebook entries will be deleted.
 Note that only the phonebook in the current language is deleted.
 Automatic downloaded phonebook entries cannot be deleted or edited.
List All Uconnect™ Phonebook
Names
 Press thebutton to begin.
 After the “Ready” prompt and the following beep, say “Phonebook
List Names”.  The Uconnect™ Phone will play
the names of all the phonebook en-
tries, including the downloaded
phonebook entries, if available.
 To call one of the names in the list, press the
button during the
playing of the desired name, and
say “Call”.
NOTE: The user can also exer-
cise “Edit” or “Delete” operations
at this point.
 The Uconnect™ Phone will then prompt you as to the number des-
ignation you wish to call.

The selected number will be dialed.PHONE CALL FEATURES
The following features can be ac-
cessed through the Uconnect™ Phone
if the feature(s) are available on your
mobile service plan. For example, if
your mobile service plan provides
three-way calling, this feature can be
accessed through the Uconnect™
Phone. Check with your mobile ser-
vice provider for the features that you
have.
89

call on hold may not become active
automatically. This is cell phone-
dependent. To bring the call back
from hold, press and hold the
but-
ton until you hear a single beep.
Redial
 Press the
button to begin.
 After the “Ready” prompt and the following beep, say “Redial”.
 The Uconnect™ Phone will call the last number that was dialed from
your mobile phone.
NOTE: This may not be the last
number dialed from the
Uconnect™ Phone.
Call Continuation
Call continuation is the progression of
a phone call on the Uconnect™ Phone
after the vehicle ignition key has been
switched to OFF. Call continuation
functionality available on the vehicle
can be any one of three types:
 After the ignition key is switched to OFF, a call can continue on the
Uconnect™ Phone either until the call ends, or until the vehicle bat-
tery condition dictates cessation of
the call on the Uconnect™ Phone
and transfer of the call to the mo-
bile phone.
 After the ignition key is cycled to OFF, a call can continue on the
Uconnect™ Phone for a certain du-
ration, after which the call is auto-
matically transferred from the
Uconnect™ Phone to the mobile
phone.
 An active call is automatically transferred to the mobile phone af-
ter the ignition key is cycled to OFF.
UCONNECT™ PHONE
FEATURES
Language Selection
To change the language that the
Uconnect™ Phone is using:
 Press the
button to begin.
 After the “Ready” prompt and the following beep, say the name of the
language you wish to switch to (English, Dutch, French, German,
Italian, or Spanish, if so equipped).
 Continue to follow the system prompts to complete language se-
lection.
After selecting one of the languages,
all prompts and voice commands will
be in that language.
NOTE: After every Uconnect™
Phone language change operation,
only the language-specific 32-
name phonebook is usable. The
paired phone name is not
language-specific and is usable
across all languages.
For command translations and alter-
nate commands in supported lan-
guages, refer to “Commands” in
“Voice Command System Operation”.
91

Reset
 Press the
button.
 After the “Ready” prompt, and the following beep, say “Setup”, then
“Reset”.
This will delete all phone pairing,
phone book entries, and other settings
in all language modes. The System
will prompt you before resetting to
factory settings.
Voice Command
 For best performance, adjust the rearview mirror to provide at least
½ in (1 cm) gap between the over-
head console (if equipped) and the
mirror.
 Always wait for the beep before speaking.
 Speak normally, without pausing, just as you would speak to a person
sitting a few feet/meters away from
you.  Make sure that no one other than
you is speaking during a voice
period.
 Performance is maximized under:  low-to-medium blower setting,
 low-to-medium vehicle speed,
 low road noise,
 smooth road surface,
 fully closed windows,
 dry weather conditions.
 Even though the system is designed for users speaking in European
English, Dutch, French, German,
Italian, or Spanish accents, the sys-
tem may not always work for some.
 When navigating through an auto- mated system such as voice mail, or
when sending a page, at the end of
speaking the digit string, make sure
to say “Send”.
 Storing names in the phonebook when the vehicle is not in motion is
recommended.  It is not recommended to store simi-
lar sounding names in the
Uconnect™ Phonebook.
 Phonebook (Downloaded and Uconnect™ Phone Local) recogni-
tion rate is optimized when the en-
tries are not similar.
 Numbers must be spoken in single digits. “800” must be spoken
“eight-zero-zero” not “eight
hundred”.
 You can say “O” (letter “O”) for “0” (zero).
 Even though international dialing for most number combinations is
supported, some shortcut dialing
number combinations may not be
supported.
 In a convertible vehicle, system per- formance may be compromised
with the convertible top down.
96

List of Preset Messages:
1. Yes
2. No
3. Where are you?
4. I need more direction.
5. L O L
6. Why
7. I love you
8. Call me
9. Call me later
10. Thanks
11. See You in 15 minutes
12. I am on my way
13. I’ll be late
14. Are you there yet?15. Where are we meeting?
16. Can this wait?
17. Bye for now
18. When can we meet
19. Send number to call
20. Start without me
Turn SMS Incoming Announce-
ment ON/OFF
Turning the SMS Incoming An-
nouncement OFF will stop the system
from announcing the new incoming
messages.
 Press the
button.
 After the “Ready” prompt and the following beep, say “Setup, Incom-
ing Message Announcement”, you
will then be given a choice to
change it. Bluetooth® Communication Link
Mobile phones have been found to
lose connection to the Uconnect™
Phone. When this happens, the con-
nection can generally be reestablished
by switching the phone off/on. Your
mobile phone is recommended to re-
main in Bluetooth® ON mode.
Power-Up
After switching the ignition key from
OFF to either the ON or ACC position,
or after a language change, you must
wait at least fifteen seconds prior to
using the system.
98

Voice CommandsPrimary Alternate (s)
zero
one
two
three
four
five
six
seven
eight
nine
asterisk (*) star
plus (+)
hash (#)
all all of them
Breakdown
service
call
cancel
confirmation
promptsconfirmation
Primary Alternate (s)
continue
delete
dial
download
Dutch Nederlands
edit
emergency
English
delete all erase all
Espanol
Francais
German Deutsch
help
home
Italian Italiano
language
list names
list phones
main menu return to main
menu
mobile
Primary Alternate (s)
mute
mute off
new entry
no
other other
pair a phone
phone pairing pairing
phonebook phone book
previous
redial
select phone select
send
set up phone settings or phone set up
transfer call
Uconnect™
Tutorial
voice training
work
yes
102

button to stop recording. You
proceed by saying one of the follow-
ing commands:
– “Save” (to save the memo)
– “Continue” (to continue record- ing)
– “Delete” (to delete the record- ing)
 “Play Memos” (to play previously recorded memos) — During the
playback you may press the Voice
Command
button to stop
playing memos. You proceed by
saying one of the following com-
mands:
– “Repeat” (to repeat a memo)
– “Next” (to play the next memo)
– “Previous” (to play the previous memo)
– “Delete” (to delete a memo)
 “Delete All” (to delete all memos)
System Setup
To switch to system setup, you may
say on of the following:
 “Change to system setup”
 “Main menu system setup”  “Switch to system setup”
 “Change to setup”
 “Main menu setup” or
 “Switch to setup”
In this mode, you may say the follow-
ing commands:
 “Language English”
 “Language French”
 “Language Spanish”
 “Language Dutch”
 “Language Deutsch”
 “Language Italian”
 “Tutorial”
 “Voice Training”
NOTE: Keep in mind that you
have to press the Voice Command
button first and wait for the
beep before speaking the “Barge
In” commands. VOICE TRAINING
For users experiencing difficulty with
the system recognizing their voice
commands or numbers the
Uconnect™ Voice “Voice Training”
feature may be used.
1. Press the Voice Command
button, say “System Setup” and
once you are in that menu then say
“Voice Training.” This will train your
own voice to the system and will im-
prove recognition.
2. Repeat the words and phrases
when prompted by Uconnect™ Voice.
For best results, the Voice Training
session should be completed when the
vehicle is parked, engine running, all
windows closed, and the blower fan
switched off. This procedure may be
repeated with a new user. The system
will adapt to the last trained voice
only.
SEATS
Seats are a part of the Occupant Re-
straint System of the vehicle.
105