2013 Lancia Thema tires

the wheel’s specifications match those
of the original wheels.
It is recommended you contact your
original equipment or an authorized
tire dealer with any questions you
may have on tire specifications or ca-
pability. Failure to use equivalent re-
placement tires may adversely affect
the safety, handling, and ride of your
vehicle.WARNING!
Do not use a tire, wheel size or
rating other than that specified for
your vehicle. Some combinations
of unapproved tires and wheels
may change suspension dimen-
sions and performance character-
istics, resulting in changes to steer-
ing, handling, and braking of your
vehicle. This can cause unpredict-
able handling and stress to steer-
ing and suspension components.
You could lose control and have a
collision resulting in serious injury
or death. Use only the tire and
wheel sizes with load ratings ap-
proved for your vehicle.
(Continued)
WARNING!(Continued)
Never use a tire with a smaller load
index or capacity, other than what
was originally equipped on your
vehicle. Using a tire with a smaller
load index could result in tire over-
loading and failure. You could lose
control and have a collision.Failure to equip your vehicle with
tires having adequate speed capa-
bility can result in sudden tire fail-
ure and loss of vehicle control.CAUTION!Replacing original tires with tires of a
different size may result in false
speedometer and odometer readings.TIRE CHAINS
(TRACTION DEVICES)
Use of Security Chain Company
(SCC) Super Z6 SZ143 or Iceman Z6
IZ-643 cables or equivalent are rec-
ommended on 225/65R17 tires. NOTE:
 These chains can be found at an
authorized LANCIA Dealership.
 Do not use tire chains on a com- pact spare tire.
Use of traction devices require suffi-
cient tire-to-body clearance. Follow
these recommendations to guard
against damage.
 Traction device must be of proper size for the tire, as recommended by
the traction device manufacturer.
 Install on Rear Tires Only.

Due to limited clearance, the Security
Chain Company (SCC) Super Z6 low
profile traction device or equivalent is
recommended on P215/65R17,
P225/60R18 or P235/55R18 tires. For an All Wheel Drive vehicle, P235/55R19 tire with the use of a
traction device that meets the SAE
type “Class S” specification is rec-
ommended.
232

WARNING!
Using tires of different size and type
(M+S, Snow) between front and
rear axles can cause unpredictable
handling. You could lose control
and have a collision.CAUTION!
To avoid damage to your vehicle or
tires, observe the following precau-
tions:
Because of restricted traction de-
vice clearance between tires and
other suspension components, it is
important that only traction de-
vices in good condition are used.
Broken devices can cause serious
damage. Stop the vehicle immedi-
ately if noise occurs that could in-
dicate device breakage. Remove
the damaged parts of the device
before further use. Install device as tightly as pos-sible and then retighten after
driving about ½ mile (0.8 km).
 Do not exceed 48 km/h.
(Continued)
CAUTION!(Continued)
 Drive cautiously and avoid severe turns and large bumps, especially
with a loaded vehicle.
 Do not drive for prolonged period on dry pavement.
Observe the traction device manu-
facturer’s instructions on the
method of installation, operating
speed, and conditions for use. Al-
ways use the suggested operating
speed of the device manufactur-
er’s if it is less than 48 km/h. Do not use traction devices on a compact spare tire.
NOTE:
In order to avoid damage
to tires, chains, and your vehicle do
not drive for a prolonged period on
dry pavement. Observe the tire
chain manufacturer's instructions
on method of installation, operating
speed, and conditions for usage.
Always use the lower suggested operat-
ing speed if both the chain manufac-
turer and vehicle manufacturer suggest
a maximum speed. This notice applies
to all chain traction devices, including
link and cable (radial) chains.
TIRE ROTATION
RECOMMENDATIONS
Tires on the front and rear axles of
vehicles operate at different loads and
perform different steering, driving,
and braking functions. For these rea-
sons, they wear at unequal rates.These effects can be reduced by timely
rotation of tires. The benefits of rotation
are especially worthwhile with aggres-
sive tread designs such as those on all
season type tires. Rotation will increase
tread life, help to maintain mud, snow,
and wet traction levels, and contribute
to a smooth, quiet ride.Refer to the “Maintenance Schedule”
for the proper maintenance intervals.
The reasons for any rapid or unusual
wear should be corrected prior to ro-
tation being performed.
233

TIRE PRESSURE
MONITOR SYSTEM
(TPMS)
The Tire Pressure Monitor System
(TPMS) will warn the driver of a low
tire pressure based on the vehicle rec-
ommended cold placard pressure.The tire pressure will vary with tem-
perature by about 0.07 BAR for every
7°C. This means that when the outside
temperature decreases, the tire pressure
will decrease. Tire pressure should al-
ways be set based on cold inflation tire
pressure. This is defined as the tire pres-
sure after the vehicle has not been
driven for at least three hours, or driven
less than 1.6 km after a three hour
period. The cold tire inflation pressure
must not exceed the maximum inflation
pressure molded into the tire sidewall.
Refer to “Tires – General Information”
in “Starting and Operating” for infor-
mation on how to properly inflate the
vehicle’s tires. The tire pressure will also
increase as the vehicle is driven - this is
normal and there should be no adjust-
ment for this increased pressure.
The TPMS will warn the driver of a
low tire pressure if the tire pressure
falls below the low-pressure warning
limit for any reason, including low
temperature effects and natural pres-
sure loss through the tire.
The TPMS will continue to warn the
driver of low tire pressure as long as
the condition exists, and will not turn
off until the tire pressure is at or above
the recommended cold placard pres-
sure. Once the low tire pressure warn-
ing (Tire Pressure Monitoring [TPM]
Telltale Light) illuminates, you must
increase the tire pressure to the rec-
ommended cold placard pressure in
order for the TPM Telltale Light to
turn off. The system will automati-
cally update and the TPM Telltale
Light will turn off once the system
receives the updated tire pressures.
The vehicle may need to be driven for
up to 20 minutes above 24 km/h in
order for the TPMS to receive this
information.For example, your vehicle may have a
recommended cold (parked for more
than three hours) placard pressure of
2.1 BAR. If the ambient temperature
is 20°C and the measured tire pres-
sure is 1.9 BAR, a temperature drop to
­7°C will decrease the tire pressure to
approximately 1.6 BAR. This tire
pressure is sufficiently low enough to
turn ON the TPM Telltale Light. Driv-
ing the vehicle may cause the tire
pressure to rise to approximately 1.9
BAR, but the TPM Telltale Light will
still be ON. In this situation, the TPM
Telltale Light will turn OFF only after
the tires are inflated to the vehicle’s
recommended cold placard pressure
value.
234

CAUTION!
The TPMS has been optimized for
the original equipment tires and
wheels. TPMS pressures and
warning have been established for
the tire size equipped on your ve-
hicle. Undesirable system opera-
tion or sensor damage may result
when using replacement equip-
ment that is not of the same size,
type, and/or style. Aftermarket
wheels can cause sensor damage.
Do not use aftermarket tire seal-
ants or balance beads if your ve-
hicle is equipped with a TPMS, as
damage to the sensors may result. After inspecting or adjusting thetire pressure, always reinstall the
valve stem cap. This will prevent
moisture and dirt from entering
the valve stem, which could dam-
age the TPM sensor. NOTE:

The TPMS is not intended to re-
place normal tire care and main-
tenance or to provide warning of
a tire failure or condition. The TPMS should not be used as
a tire pressure gauge while ad-
justing your tire pressure.
Driving on a significantly under-
inflated tire causes the tire to
overheat and can lead to tire fail-
ure. Under-inflation also reduces
fuel efficiency and tire tread life,
and may affect the vehicle’s han-
dling and stopping ability.The TPMS is not a substitute for
proper tire maintenance, and it
is the driver’s responsibility to
maintain correct tire pressure us-
ing an accurate tire pressure
gauge, even if under-inflation has
not reached the level to trigger
illumination of the TPM Telltale
Light.Seasonal temperature changes
will affect tire pressure, and the
TPMS will monitor the actual tire
pressure in the tire.
PREMIUM SYSTEM
The Tire Pressure Monitor System
(TPMS) uses wireless technology with
wheel rim mounted electronic sensors
to monitor tire pressure levels. Sen-
sors mounted to each wheel as part of
the valve stem transmit tire pressure
readings to the receiver module.
NOTE: It is particularly impor-
tant for you to check the tire pres-
sure in all of the tires on your ve-
hicle monthly and to maintain the
proper pressure.
The TPMS consists of the following
components:
 Receiver module,
 Four TPM sensors,
 Various TPMS messages, which display in the Electronic Vehicle
Information Center (EVIC), and
 TPM Telltale Light
235

Tire Pressure Monitoring Low
Pressure WarningsThe TPM Telltale Light will
illuminate in the instrument
cluster and a chime will sound
when tire pressure is low in one or
more of the four active road tires. In
addition, the EVIC will display an
“Inflate Tire to XX” message for a
minimum of five seconds and a "LOW
TIRE" message and a graphic show-
ing the pressure values of each tire
with the low tire pressure values flash-
ing. The recommended cold placard
pressure inflation value is the pressure
value displayed in the "Inflate Tire to
XX" message displayed in the EVIC.
Should this occur, you should stop as
soon as possible and inflate the tires
with a low pressure condition (those
flashing in the EVIC graphic) to the
vehicle’s recommended cold placard
pressure inflation value. Once the sys-
tem receives the updated tire pres-
sures, the system will automatically update, the “Inflate Tire to XX” mes-
sage will no longer be displayed, the
graphic display in the EVIC will stop
flashing, and the TPM Telltale Light
will turn off. The vehicle may need to
be driven for up to 20 minutes above
24 km/h in order for the TPMS to
receive this information.
Service TPMS Warning
If a system fault is detected, the TPM
Telltale Light will flash on and off for
75 seconds and then remain on solid.
The system fault will also sound a
chime. In addition, the EVIC will dis-
play a "SERVICE TPM SYSTEM"
message for a minimum of five sec-
onds and then display dashes (- -) in
place of the pressure value to indicate
which sensor is not being received.
If the ignition switch is cycled, this
sequence will repeat, providing the
system fault still exists. If the system
fault no longer exists, the TPM Tell-
tale Light will no longer flash, and the
"SERVICE TPM SYSTEM" message
will no longer display, and a pressurevalue will display in place of the
dashes. A system fault can occur due
to any of the following:
1. Signal interference due to elec-
tronic devices or driving next to facili-
ties emitting the same radio frequen-
cies as the TPM sensors.
2. Installing aftermarket window
tinting that contains materials that
may block radio wave signals.
3. Accumulation of snow or ice
around the wheels or wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped
with TPM sensors.
The EVIC will also display a "SER-
VICE TPM SYSTEM" message for a
minimum of five seconds when a sys-
tem fault related to an incorrect sen-
sor location fault is detected. In this
case, the "SERVICE TPM SYSTEM"
message is then followed with a
graphic display with pressure values
still shown. This indicates that the
pressure values are still being received
from the TPM sensors but they may236

not be located in the correct vehicle
position. The system still needs to be
serviced as long as the "SERVICE
TPM SYSTEM" message is displayed.
Vehicles With Compact Spare
1. The compact spare tire does not
have a TPM sensor. Therefore, the
TPMS will not monitor the pressure in
the compact spare tire.
2. If you install the compact spare
tire in place of a road tire that has a
pressure below the low-pressure
warning limit, upon the next ignition
switch cycle, the TPM Telltale Light
will remain ON and a chime will
sound. In addition, the graphic in the
EVIC will still display a flashing pres-
sure value.
3. After driving the vehicle for up to
20 minutes above 24 km/h, the TPM
Telltale Light will flash on and off for
75 seconds and then remain on solid.
In addition, the EVIC will display a
"SERVICE TPM SYSTEM" message
for a minimum of five seconds and
then display dashes (- -) in place of
the pressure value.4. For each subsequent ignition
switch cycle, a chime will sound, the
TPM Telltale Light will flash on and
off for 75 seconds and then remain on
solid, and the EVIC will display a
"SERVICE TPM SYSTEM" message
for a minimum of five seconds and
then display dashes (- -) in place of
the pressure value.
5.
Once you repair or replace the
original road tire and reinstall it on the
vehicle in place of the compact spare,
the TPMS will update automatically.
In addition, the TPM Telltale Light
will turn OFF and the graphic in the
EVIC will display a new pressure value
instead of dashes (- -), as long as no
tire pressure is below the low-pressure
warning limit in any of the four active
road tires. The vehicle may need to be
driven for up to 20 minutes above
24 km/h in order for the TPMS to
receive this information.
TPMS DEACTIVATION
The TPMS can be deactivated if re-
placing all four wheel and tire assem-
blies (road tires) with wheel and tire
assemblies that do not have TPMS
Sensors, such as when installing
winter wheel and tire assemblies on
your vehicle. To deactivate the TPMS,
first, replace all four wheel and tire
assemblies (road tires) with tires not
equipped with Tire Pressure Monitor-
ing (TPM) Sensors. Then, drive the
vehicle for 20 minutes above
24 km/h. The TPMS will chime, the
“TPM Telltale Light” will flash on
and off for 75 seconds and then re-
main on and the Electronic Vehicle
Information Center (EVIC) will dis-
play the “SERVICE TPM SYSTEM”
message and then display dashes (--)
in place of the pressure values. Begin-
ning with the next ignition switch
cycle, the TPMS will no longer chime
or display the “SERVICE TPM SYS-
TEM” message in the EVIC but
dashes (--) will remain in place of the
pressure values.
237

To reactivate the TPMS, replace all
four wheel and tire assemblies (road
tires) with tires equipped with TPM
sensors. Then, drive the vehicle for up
to 20 minutes above 24 km/h. The
TPMS will chime, the “TPM Telltale
Light” will flash on and off for 75 sec-
onds and then turn off, and the Elec-
tronic Vehicle Information Center
(EVIC) will display the “SERVICE
TPM SYSTEM” message. The EVIC
will also display pressure values in
place of the dashes. On the next igni-
tion switch cycle the “SERVICE TPM
SYSTEM” message will no longer be
displayed as long as no system fault
exists.FUEL REQUIREMENTS —
GASOLINE ENGINES3.6L ENGINE
All engines are designed to meet all
emissions regulations and provide ex-
cellent fuel economy and performance
when using high quality unleaded
gasoline with a minimum research oc-
tane rating of 91. The use of premiumgasoline is not recommended, as it
will not provide any benefit over regu-
lar gasoline in these engines.
Light spark knock at low engine speeds
is not harmful to your engine. How-
ever, continued heavy spark knock at
high speeds can cause damage, and
immediate service is required. Poor
quality gasoline can cause problems
such as hard starting, stalling, and
hesitations. If you experience these
symptoms, try another brand of gaso-
line before considering service for the
vehicle.
Over 40 auto manufacturers world-
wide have issued and endorsed consis-
tent gasoline specifications (the World-
wide Fuel Charter, WWFC) which
define fuel properties necessary to de-
liver enhanced emissions, perfor-
mance, and durability for your vehicle.
The manufacturer recommends the use
of gasoline that meets the WWFC
specifications if they are available.Besides using unleaded gasoline with
the proper octane rating, gasolines
that contain detergents, corrosion and
stability additives are recommended.Using gasolines that have these addi-
tives may help improve fuel economy,
reduce emissions, and maintain ve-
hicle performance.
Poor quality gasoline can cause prob-
lems such as hard starting, stalling
and stumble. If you experience these
problems, try another brand of gaso-
line before considering service for the
vehicle.
Methanol
(Methyl or Wood Alcohol) is used in
a variety of concentrations when
blended with unleaded gasoline. You
may find fuels containing 3% or more
Methanol along with other alcohols
called cosolvents. Problems that re-
sult from using Methanol/gasoline or
E-85 Ethanol blends are not the re-
sponsibility of the manufacturer.
While MTBE is an oxygenate made
from Methanol, it does not have the
negative effects of Methanol.
238

TOWING REQUIREMENTS
To promote proper break-in of your
new vehicle drivetrain components
the following guidelines are recom-
mended:CAUTION!
 Do not tow a trailer at all duringthe first 805 km the new vehicle is
driven. The engine, axle or other
parts could be damaged.
 Then, during the first 805 km
that a trailer is towed, do not
drive over 80 km/h and do not
make starts at full throttle. This
helps the engine and other parts
of the vehicle wear in at the
heavier loads.WARNING!
Improper towing can lead to an in-
jury collision. Follow these guide-
lines to make your trailer towing as
safe as possible:
(Continued)
WARNING!(Continued)
 Make certain that the load is se- cured in the trailer and it will not
shift during travel. When traile-
ring cargo that is not fully se-
cured, dynamic load shifts can
occur that may be difficult for the
driver to control. You could lose
control of your vehicle and have a
collision.
 When hauling cargo or towing a trailer, do not overload your ve-
hicle or trailer. Overloading can
cause a loss of control, poor per-
formance, or damage to brakes,
axle, engine, transmission, steer-
ing, suspension, chassis structure,
or tires.
Safety chains must always be used
between your vehicle and trailer.
Always connect the chains to the
frame or hook retainers of the ve-
hicle hitch. Cross the chains under
the trailer tongue and allow
enough slack for turning corners.
(Continued)
WARNING! (Continued)
 Vehicles with trailers should not be parked on a grade. When
parking, apply the parking brake
on the tow vehicle. Put the tow
vehicle automatic transmission in
PARK. Always, block or "chock"
the trailer wheels.
 GCWR must not be exceeded.
 Total weight must be distrib-
uted between the tow vehicle
and the trailer such that the
following four ratings are not
exceeded:
1. Max loading as defined on the
“Tire and Loading Information”
placard.
2. GTW
3. GAWR
4.
Tongue weight rating for the
trailer hitch utilized. (This re-
quirement may limit the ability to
always achieve the 10% to 15%
range of tongue weight as a per-
centage of total trailer weight.)
246