2013 Lancia Delta Owner handbook (in English)

1
KNOWING YOUR CAR15
Start&Stop SYSTEM
ACTIVATION/DEACTIVATION
(for versions/markets, where provided)
Start&Stop SYSTEM FAULT
Start&Stop system activation
A message and a symbol Uwill appear on the display
when the Start&Stop system is activated. In this condi-
tion, the LED on the button Tis off.
Turning the Start&Stop off
–Versions with reconfigurable multifunction display: the
Tsymbol will appear on the display when the Start&Stop
system is off.
The LED on the Tbutton will be on when the system
is off.
Start&Stop SYSTEM FAILURE
(versions with reconfigurable
multifunction display)
A message and the symbol jwill appear on the dis-
play when the Start&Stop system is faulty. In this case,
go to a Lancia Dealership.
U
j
Engine coolant overheating (red)
Turning the key to the MAR position the
warning light switches on, but it will switch off
after a few seconds. The warning light turns on
when the engine is overheated. If the warning light comes
on when driving, proceed as follows:
❍normal driving conditions: stop the car, switch off the
engine and check that the water level in the reservoir
is not below the MIN mark.
In this case, wait for a few minutes for the engine to cool
down, then slowly and carefully open the cap, top-up with
coolant and check that the level is between the MIN and
MAX reference on the reservoir itself. Also check for any
fluid leaks. Go to a Lancia Dealership if the warning light
should switch on when the engine is started again.
u

16KNOWING YOUR CAR
❍if the vehicle is used under demanding conditions (e.g.
towing trailers uphill or fully loaded): slow down and,
if the light stays on, stop the car. Wait for 2 or 3 min-
utes with the engine running and slightly accelerated
to further accelerate the coolant circulation. Then stop
the engine. Check the correct liquid level as described
above.
IMPORTANT Over demanding routes, it is advisable to
keep the engine on and slightly accelerated for a few min-
utes before switching it off.
The display will show a dedicated message.
Doors not closed correctly (red)
This warning light switches on when one or
more doors are not properly shut. An acoustic
signal is activated with the doors open and the
car moving. The warning light in the multifunction dis-
play also switches on when the bonnet and/or tailgate are
not properly shut. The display will show a dedicated mes-
sage.
´
General failure indication (amber)
Fuel cut-off activated
This warning light (or symbol on the display)
switches on when the fuel cut off system inter-
venes. The display shows the dedicated message.
Engine oil pressure sensor failure
This warning light (or symbol on the display) switches on
when a failure is detected in the engine oil pressure sen-
sor. The display shows the dedicated message.
Dusk sensor failure
This warning light (or symbol on the display) switches on
when a failure is detected in the dusk sensor.
Speed limit exceeded
This warning light (amber), or symbol on the display
(red), switches on when the preset speed limit is exceeded
(for Arab countries the speed limit is set at 120 km/h).
The display shows the dedicated message.
Rain sensor fault
(for versions/markets, where provided)
This warning light (or symbol on the display) switches on
when a fault is detected in the rain sensor. The display
shows the dedicated message.
Start&Stop fault
(for versions/markets, where provided)
(versions with multifunction display)
The warning light comes on when a failure is detected in
the Start&Stop system. The display will show a dedicated
message.
è

1
KNOWING YOUR CAR17
Parking sensor fault
(for versions/markets, where provided)
This warning light (or symbol on the display) switches on
when a fault is detected in the parking sensors. The dis-
play shows the dedicated message.
Tyre pressure monitoring system (TPMS) failure
(for versions/markets, where provided)
This warning light (or symbol on the display) switches on
when a failure is detected in the T.P.M.S. system (where
provided). Should one or more wheels without a sensor
be fitted, the instrument panel warning light will come
on and stay on until the initial conditions are restored.
The display shows the dedicated message.
NOTE If one of the above mentioned faults occurs,
contact a Lancia Dealership as soon as possible.
AFS system failure
This warning light (or symbol on the display) switches on
when a failure is detected in the AFS system (see “Head-
lights” paragraph in this chapter). The display shows the
dedicated message.
Steering corrector not available
This warning light (or symbol on the display) switches on
when the steering corrector is not available. The display
will show a dedicated message.DPF (diesel particulate filter) cleaning
in progress (only Multijet versions
with DPF) (amber)
When the key is turned to the MAR–ON position
the warning light comes on but should go out after a few
seconds. The warning light turns on constantly when the
DPF system needs to eliminate the trapped pollutants
through the regeneration process.
The warning light does not come on every time the DPF
is being regenerated, rather only when the driving con-
ditions are such that the driver needs to know it. To
switch the warning light off, the car must be kept mov-
ing until the regeneration process is completed.
As an average, the process lasts fifteen minutes. The best
conditions to complete the regeneration process are
reached driving the car at about 60 km/h with engine
speed over 2000 rpm. When this warning light switches
on, it does not indicate a car failure and thus it should not
be taken to a workshop. For versions/markets where pro-
vided, the display shows the dedicated message and the
warning light comes on.
h

18KNOWING YOUR CAR
Fuel reserve (amber)
When the key is turned to the MAR position the
warning light comes on but should go out af-
ter a few seconds. The warning light switches on
when about 5 to 7 litres of fuel are left in the tank.
The display shows the dedicated message.
IMPORTANT The warning light will blink to indicate
a system failure. Go to a Lancia Dealership to have the sys-
tem checked.
K
Always drive at a speed appropriate to the
traffic conditions, the weather and speed lim-
its. The engine can also be switched off if the
DPF warning light is on; nevertheless, repeated in-
terruptions of the regeneration process could cause an
early decay of engine oil. For this reason, always wait
until the warning light switches off before stopping the
engine as described above. It is not a good idea to com-
plete DPF regeneration with the vehicle stationary.ignition system that could cause excessive exhaust emis-
sions, a possible loss of performance, poor driveability
and high fuel consumption. On some versions the display
shows the dedicated message. Under these conditions,
you may continue travelling at moderate speed without
demanding excessive effort from the engine. Prolonged
use of the car with the warning light on may cause dam-
age. Go to a Lancia Dealership as soon as possible.
The warning light goes off if the failure disappears, but
it is still stored by the system.
Petrol engines only
If the warning light is flashing, this indicates that the cat-
alytic converter may be damaged.
If the warning light flashes, it is necessary to release the
accelerator pedal to lower the speed of the engine until
the warning light stops flashing; continue the journey at
moderate speed, trying to avoid driving conditions that
may cause further flashing and contact a Lancia Deal-
ership as soon as possible.
EOBD/injection system failure (amber)
Under normal conditions, when the ignition
key is turned to MAR, the warning light
switches on, but should switch off as soon as the
engine is started.
If the warning light remains on or switches on whilst dri-
ving, that means that the injection system is not work-
ing properly; in particular, if the warning light switches
on constantly, this indicates a malfunction in the supply/
U
If, turning the ignition key to MAR, the warn-
ing light Udoes not turn on or if it turns on
steadily or flashing when travelling (on cer-
tain versions together with the message on the dis-
play), contact a Lancia Dealership as soon as pos-
sible. The operation of the warning light Umay be
checked by the traffic control authorities using spe-
cific devices. Always comply with the traffic regu-
lations in force in the country where you are driving.

1
KNOWING YOUR CAR19
Advanced ESP system (amber)
When the key is turned to the MAR position
the warning light comes on but should go out
after a few seconds. If the warning light does not
switch off or stays on together with the LED on the ASR
button when travelling, contact a Lancia Dealership. On
some versions the display shows the dedicated message.
If the warning light flashes when driving, this indicates
that the Advanced ESP system is activated.
If the battery is disconnected, the warning light áwill
switch on (together with a message in the display) to in-
dicate that the system must be realigned.
To switch the warning light off, carry out the following
initialisation procedure:
❍turn the ignition key to MAR:
❍turn the steering wheel fully both clockwise and anti-
clockwise (to move from the position with the wheels
straight);
❍turn the ignition key to STOP and then to MAR.
If the warning light
ádoes not go out after a few seconds,
seek assistance from a Lancia Dealership.
á
Hill Holder failure (amber)
The
áwarning light switches on to indicate
a Hill holder system failure. In this case, go to
a Lancia Dealership as soon as possible. Al-
ternatively, on some versions the
*symbol
switches on in the display.
The display will show a dedicated message.
á
*
Glow plugs
This warning light switches on when the key
is turned to MAR. It will switch off as soon as
the heater plugs have reached a preset temper-
ature. Start the engine as soon as the warning light
switches off.
IMPORTANT In hot outside temperatures, the warning
light may stay on for only a very short time.
Glow plug warming failure
The warning light flashes if there is a fault in the pre-
heating system. Go to a Lancia Dealership as soon as pos-
sible.
The display will show a dedicated message.
m

Lancia Code system failure (amber)
This warning light (or symbol on the display),
when on constantly with the ignition key
turned to MAR, indicates a possible failure (see
“Lancia Code system”).
If the
Ywarning light (or symbol in the display) is flash-
ing, this means that the vehicle is not protected by the en-
gine immobilizer device (see “Lancia Code system”).
Contact a Lancia Dealership to have all the keys pro-
grammed.
Alarm failure
(for versions/markets, where provided)
A failure in the alarm system is signalled by this warn-
ing light (or symbol in the display) switching on. Contact
a Lancia Dealership as soon as possible.
The display shows the dedicated message.
Break in attempt
(for versions/markets, where provided)
This warning light (or symbol in the display) switches on
when a break in attempt is detected. Contact a Lancia
Dealership as soon as possible.
The display will show a dedicated message. ABS system failure (amber)
When the key is turned to the MAR–ON posi-
tion the warning light comes on but should go
out after a few seconds. The warning light will
light up when the system is either not working or not
available. Under these circumstances the braking system
will work as normal without the extra performance of-
fered by the ABS system.
Drive carefully and go to a Lancia Dealership as soon
as possible.The display will show a dedicated message.
Drive carefully and go to a Lancia Dealership as soon a
>
20KNOWING YOUR CAR
Water in the diesel filter
(Multijet versions) (amber)
When the key is turned to the MAR position
the warning light comes on but should go out af-
ter a few seconds. The warning light turns on when there
is water in the diesel filter. The display will show
a dedicated message.
c
The presence of water in the supply circuit
may cause severe damage to the injection
system and irregular engine operation. If
warning light
clights up (on some versions with
the message on the display), go to a Lancia Deal-
ership as soon as possible to have the system bled.
Water may have entered the tank if this appears im-
mediately after refuelling: if this happens, switch
the engine off immediately and contact a Lancia
Dealership.
Y

1
KNOWING YOUR CAR21
Insufficient tyre pressure
(for versions/markets where provided)
This warning light switches on when the igni-
tion key is turned to MAR, but it should switch
off after a few seconds. The warning light (amber), or
symbol in the display (red), switch on when the inflation
pressure of one or more tyres falls below a preset level.
In this way the T.P.M.S. warns the driver and signals the
possibility of the tyre being dangerously deflated and a
probable puncture (see paragraph “T.P.M.S.” in this
chapter).
IMPORTANT Do not continue driving with one or more
flat tyres as handling may be compromised. Stop the car,
avoiding harsh braking or steering manoeuvres. Replace
the wheel immediately with the space-saver wheel (for
versions/markets where provided) or carry out a repair
using the dedicated kit (see “Changing a wheel” in the
chapter “4”) and contact a Lancia Dealership as soon as
possible.
Check tyre pressures
This warning light (for versions/markets where provided)
switches on when the ignition key is turned to MAR, but
it should switch off after a few seconds.
The warning light (or symbol in the display) switches on
to show the flat tyre (see “T.P.M.S.” paragraph in this
chapter).
n
Should two or more tyres be flat, the display will show
the indications corresponding to each tyre in sequence.
Restore the correct inflation pressure values as soon as
possible (see paragraph “Cold tyre pressures” in chap-
ter “6”).
Tyre pressure unsuitable for speed
This warning light (for versions/markets where provided)
switches on when the ignition key is turned to MAR, but
it should switch off after a few seconds.
Should it be necessary to travel at a speed higher than
160 km/h, inflate the tyres more than the pressure value
specified in paragraph “Cold tyre pressures” in chapter
“6”.
If the T.P.M.S. system (for versions/markets where pro-
vided) detects that the pressure of one or more tyres is
unsuitable for the current speed, the warning light or
symbol will switch on (together with the message on the
display) (see “Tyre pressure low” in this chapter) and
it will stay on until the car slows down to a speed below
the preset threshold (see “T.P.M.S.” paragraph in this
chapter).
IMPORTANT In this case, slow down immediately be-
cause tyre overheating could damage tyre performance
and durability beyond repair, and may even make the
tyre explode.

22KNOWING YOUR CAR
Particularly strong radio frequency interfer-
ence may cause the T.P.M.S. system to func-
tion incorrectly. This condition is indicated
to the driver by a message (for versions/markets
where provided).
The message will disappear automatically as soon
as the interference ceases to disturb the system.
Exterior lights failure (amber)
This warning light (or symbol on the display)
switches on when a failure is detected in any
of the following lights:
❍side lights;
❍brake lights (for versions/markets where provided);
❍rear fog lamps;
❍direction indicators;
❍number plate lights;
❍day lights.
The failure relating to these lights could be: one or more
blown bulbs, a blown protection fuse or a break in the
electrical connection.
The display shows the dedicated message.
W
Rear fog lamps (amber)
The warning light switches on activating the
rear fog lamps.
4
Front fog lights (green)
The warning light comes on when the front fog
lights are turned on.
5
Direction indicators
(green – intermittent)
The warning lights switch on when the direc-
tion indicator control lever is moved down-
wards, upwards or when the hazard warning
light button is pressed.
F
D
Day lights/dipped beam headlights
(green)
This warning light switches on when the day
lights or dipped beam headlights are activated.
Follow me home
This warning light comes on when this device is activated
(see “Follow me home”).
The display will show a dedicated message.
3