2013 Citroen DS5 HYBRID4 engine

System which manages the duration of use of cer tain functions to conser ve a sufficient level of
charge in the battery.
After the engine has stopped, you can still use functions such as the audio and telematics
system, windscreen wipers, dipped beam headlamps, cour tesy lamps, etc. for a maximumcombined duration of about for ty minutes.






Energy economy mode


Switching to economy mode
A message then appears in the instrument
panel screen indicating that the vehicle has
switched to econom
y mode and the active
functions are put on standby.
If a telephone call is being made at this time, it
will be maintained for around 1
0 minutes with
the Bluetooth hands-free system of your audio
system.


Exiting economy mode

These functions are reactivated automaticallynext time the vehicle is driven.
In order to restore the use of these functionsimmediately, star t the engine and let it run:


- for less than ten minutes, to use the
equipment for approximately five minutes,

- for more than ten minutes, to use theequipment for up to approximatelythirty minutes.
Let the engine run for the duration specified toensure that the battery charge is sufficient.
Do not repeatedly and continuously restar t theengine in order to charge the battery.
A flat battery prevents the engine from star ting (refer to the "Battery" section).
In this energy economy mode and whenstarting up the hybrid system, it maytake a few seconds before the Readylamp comes on.









Load reduction mode
System which manages the use of certainfunctions according to the level of chargeremaining in the battery.
When the vehicle is being driven, the loadreduction function temporarily deactivates cer tain functions, such as the air conditioning,
the heated rear screen...
The deactivated functions are reactivated automatically as soon as conditions permit.

Practical information








Changing a wiper blade


Before removing a front
wi
per bladeRemovin
g
) Raise the corresponding wiper arm. )
Unclip the wiper blade and remove it.

Fitting
)
Put the corresponding new wiper blade in
place and clip it.) Fold down the wiper arm carefully.
After fitting a front wiper
blade
)
Switch on the ignition. )
Operate the wiper stalk again to park the
wiper blades.







Recovering the
vehicle on a fl at-bed


Procedure for having your vehicle recovered on
a flat bed lorry or trailer.
Always recover the vehicle on a flat bed lorry or trailer. Never tow the vehicle with the four wheels on the ground (or the front or rear wheels only), you risk damaging the transmission. Place the gear selector in position Nand switch off the engine ( Ready
lamp off).
)Within one minute after switching off
the ignition, operate the wiper stalk toposition the wiper blades ver tically on the
windscreen.

From the front
From the rear Access to the tools
The towing eye is installed in the boot under
the floor.To gain access to it:)open the boot, )remove the towing eye, located in the toolbox.

)
On the front bumper, unclip the cover by
pressing at the bottom to disengage the securing lugs. ) Screw the towing eye in fully.)
Install the towing system.)
Switch on the hazard warning lamps.

)On the rear bumper, unclip the cover by
levering at the left with the point of the
towing eye. )Screw the towing eye in fully. )Install the towing system. )Switch on the hazard warning lamps.

)Place the gear selector inneutral - position N.Failure to obser ve this special conditioncould result in damage to cer tainbraking components and the absenceof braking assistance the next time theengine is started.

When towing with the engine off, there is no longer any braking or steering assistance.

We recommend the use of genuine
CITROËN towbars and their harnesses that have been tested and approved from the design stage of your vehicle,and that the fitting of the towbar is
entrusted to a CITROËN dealer or aqualified workshop.
If the towbar is not fitted by a CITROËN dealer, it is imperative that it isfitted in accordance with the vehiclemanufacturer's instructions.


Driving advice


Distribution of loads
)
Distribute the load in the trailer so that the
heaviest items are as close as possible to
t
he axle and the nose weight approaches the
maximum permitted without exceeding it.
Air density decreases with altitude, thus
reducing engine performance. Above
1 000 metres, the maximum towed load must
be reduced by 10 % for every 1 000 metres of altitude.


Side wind
)
Take into account the increased sensitivity
to side wind.



Cooling

To w i ng a trailer on a slope increases the
temperature of the coolant.
As the
fan is electrically controlled, its cooling capacity is not dependent on the engine speed.)
To lower the engine speed, reduce your speed.
)
If the warning lamp and the STOPwarning lamp come on,stop the vehicle and switch off
the engine as soon as possible.

Braking

To w i ng a trailer increases the braking distance.
To avoid overheating of the brakes on a longmountain type of descent, the use of engine braking is recommended.

Tyres
)Check the tyre pressures of the towingvehicle and of the trailer, obser ving the recommended pressures.



Lighting
)Check the electrical lighting and signalling on the trailer.


The rear parking sensors will be deactivated automatically if a genuine CITROËN towbar is used.



Driving with a trailer places greater demands on the towing vehicle and thedriver must take par ticular care.

The maximum towed load on a long incline depends on the gradient and the ambient
tem
perature.
In all cases, keep a check on the coolant
temperature.

R
efer to the "Technical data" section for detailsof the weights and towed loads which apply toyour vehicle.

239Checks
Opening the bonnet
Opening
)
From inside
: pull the release lever, located
on the left below the dashboard, towards you.
Before doing anything under the bonnet,
switch off the ignition (Ready lamp off) to avoid any risk of injury resulting fromautomatic operation of the engine.


Closing
)
Lower the bonnet and release it at the endof its travel. )
Check that it is latched correctly.


)From the outside: lift the safety catch and
raise the bonnet.
A bonnet strut opens the bonnet and holds itopen.


Never touch, handle or remove the orange "high voltage" cables.

The use of a high pressure jet wash under the bonnet is strictly prohibited,in order to avoid damage to the electriccomponents.

The various caps and covers allow access for
checking the levels of the various fluids, for replacing cer tain components and for primingthe fuel system.














Diesel engine
1.
Power steering reservoir.2.
Screenwash and headlamp wash reser voir.3.
Coolant reservoir. 4.
Brake fluid reservoir.5.
Battery / Fuses.
6.Fusebox.
7. Air filter.8.Engine oil dipstick. 9.
Engine oil filler cap.10.Priming pump. 11.
Bleed screw.
HDi 160 PEF 6-SPEED ELECTRONIC GEARBOX

241Checks
On vehicle fitted with HDi engines, the fuel
system must be primed if you run out of fuel;
refer to the corresponding engine compar tment
view.











Running out of fuel (Diesel)


If the tank on your vehicle is fitted witha misfuel prevention device, refer to the"Misfuel prevention (Diesel)" section.
)
Fill the fuel tank with at least five litres of Diesel.)
Open the bonnet. )
If necessary, unclip the style cover for
access to the priming pump.
) Slacken the bleed screw. )
Squeeze and release the priming pump
repeatedly until fuel appears in the
transparent pipe.
) Tighten the bleed screw.)
Operate the star ter until the engine star ts (if the engine fails to star t at the first
attempt, wait around 15 seconds before
trying again).) If the engine fails to star t after a few
attempts, operate the priming pump again,
th
en the starter.) Put the style cover back in position and clip it in place, ensuring that it has clippedcorrectly. )
Close the bonnet.

2 litre HDi engine


If the engine does not star t first time, don't keep trying. Star t the procedure
again from the beginning.

Before doing anything under the bonnet, switch off the ignition ( Readylamp off)to avoid any risk of injury resulting from automatic operation of the engine.

Checking levels


Ta k e c a r e w h e n w o r k i ng under the bonnet, as certain areas of the enginemay be extremely hot (risk of burns) and the cooling fan could star t at any time(even with the ignition off).
Oil level
The check is carried out either when
the ignition is switched on using the oil level indicator in the instrument panel, or using the dipstick.
It is normal to top up the oil level between two ser vices (or oil changes). CITROËN recommends that you checkthe level, and top up if necessary, every 3 000 miles (5 000 kms). After topping up the oil, the check when
switching on the ignition with the oillevel indicator in the instrument panelis not valid during the 30 minutes after topping up. If a level drops significantly, have the corresponding system checked by a CITRO
ËN dealer or a qualified workshop. Check all of these levels regularly, in line with the ser vicing booklet and the requirements of the warranties. Top them up if necessary, unless other wise indicated.





Before doing anything under the bonnet,switch off the ignition (Readylamp off) to avoid any risk of injury resulting from automatic operation of the engine.


Engine oil change

Refer to the servicing and warranty booklet for
details of the interval for this operation.
In order to maintain the reliabilit
y of the engine
and emission control system, the use of
additives in the engine oil is prohibited.


Oil specifi cation

The oil must be the correct grade for your engine and conform to the manufacturer's
recommendations. It will onl
y be correct if the vehicle is on level
ground and the engine has been off for more
than 30 minutes.