2013 Citroen C4 PICASSO engine

142
Driving
Label on door panel
Before leaving the vehicle, check thatparking brake is applied: the indicator lamps in the instrument panel andthe control lever must be on fixed, not flashing.
If the parking brake is not applied, there is an audible signal and a message isdisplayed on opening the driver's door.


Never leave a child alone inside thevehicle with the ignition on, as theycould release the parking brake.
When towing, parking on a steepslope, or if your vehicle is heavilyladen, turn the wheels towards the kerb and engage a gear (with a manual or electronic gearbox) or place the gear selector in position P
with an automaticgearbox).For towing, you vehicle is approved for parking on slopes of up to 12%.


Manual operation


Application of of the parking brake
is confirmed by illumination of the
brake indicator lamp and the Pindicator lamp in the control lever,
accompanied by the display of the
message "Parking brake applied".

Manual release

With the ignition on or the engine running, to
release the parking brake: )press the brake pedal, )while maintaining pressure on the brakepedal, briefly push the control lever.
The complete release o
f the parking brake is confirmed by the brake indicator lamp and thePindicator lamp in the control lever going off,
accompanied by the display of the message
"Parking brake released".


If you push the control lever withoutpressing the brake pedal, the parkingbrake will not be released and a message is displayed.


Manual application

With the vehicle stationary: briefly pull the control lever.

Confirmation of the instruction is signaled by
flashing of the indicator lamp in the control
lever.

143
4
Driving
With the vehicle stationary, the parking brakeis automatically applied when the engine is switched offby pressing the START/STOP fbutton.

Application o
f of the parking brake
is confirmed by illumination of the
brake indicator lamp and the Pindicator lamp in the control lever, accompanied by the display of the message "Parking brake applied".

With the engine stalled or in STOP mode of Stop & Star t, automatic application does not take place.


In automatic mode, you can manuallyapply or release the parking brake using the control lever.


Automatic operation


Automatic release


The complete release of the parkingbrake is confirmed by the brake
indicator lamp and the P indicator
lamp in the control lever going off,
accompanied by the display of the
message "Parking brake released".
When stationary with the engine running, do notdepress the accelerator pedal unnecessarily,you risk releasing the parking brake.
Ensure first that the engine is running and the
driver's door is properly closed.
The electric parkin
g brake releases automatically and progressivelywhen youpress the accelerator: )Manual gearbox: fully depress the clutchpedal, engage 1 st
or reverse gear; press
the accelerator pedal and let up the clutch pedal. )Automatic gearbox: select position D , Mor Rthen press the accelerator. )Electronic gearbox: select position A, Mor Rthen press the accelerator pedal.



Automatic application

144
Driving
Special cases
Application of of the parking brake
is confirmed by illumination of the brake indicator lamp and the Pindicator lamp in the control lever,
accompanied by the display of the
message "Parking brake applied". The complete release of the parkin
gbrake is confirmed by the brake
indicator lamp and the Pindicator lamp in the control lever going off,
accompanied by the display of the
message "Parking brake released".
In some situations, you may need to operate
the parking brake manually.
Immobilisation of the vehicle
with the engine running
To immobilise the vehicle with the enginerunning, briefly pull the control lever.
Parking the vehicle with the brake released
In very cold conditions, it is recommended that the parking brakenot be applied (risk of freezing).
To i m m o b i l i s e your vehicle, engage a gear or fit a chock to one of the wheels.
Immobilisation of the vehicle with the
parking brake released
) Switch off the engine.
Illumination of the warning lamps in the
instrument panel and control lever confirm
application of the parkin
g brake, ) Switch on the ignition again, withoutstarting the engine.)
Release the parking brake manually by
pushing the control lever while keepingyour foot on the brake.
)Switch off the ignition.

145
4
Driving

Emergency braking


In the event of a failure of the main servicebrake or in an exceptional situation (e.g. driver
taken ill, under instruction, etc
) a continuous
pull on the control lever will brake the vehicle.
Brakin
g takes place while the control lever is
being pulled. It is interrupted if the control lever
is released.
The ABS and DSC systems provide stability of
the vehicle during emergency braking.
If the emergency braking malfunctions, the
message "Parking brake control faulty" will be
displayed.

I
f a failure of the ABS and DSC systems, signalled by the illumination of one or both
warning lamps in the instrument panel, thenstability of the vehicle is no longer guaranteed.
In this event, stability must be assured by the
driver by repeating alternate "pull-release" actions on the control lever until the vehicle is immobilised.



The emergency braking should only be used in an exceptional situation.
Re
peat this procedure to reactivate automatic
operation.
Reactivation of automatic operation is
confirmed by the indicator lamp in the instrument panel going off.

Deactivating automatic
o
peration

In some situations, such as very cold weather
or towing (caravan, recovery), it may be necessary to deactivate automatic operation of
the system. )Star t the engine.)Apply the parking brake with the control
lever, if it is released. )Ta k e your foot off the brake pedal.)Push and hold the control lever in the release direction for at least 10 seconds and no more than 15 seconds.)Release the control lever. )Press and hold the brake pedal. )Pull the control lever in the apply direction
for 2 seconds.
D
eactivation of the automatic functions
is confirmed by illumination of this
indicator lamp in the instrument panel.
)Release the control lever and the brake pedal.
From this point the parkin
g brake can only
be applied and released manually using the control lever.

146
Driving
The various alert situations are described in the table below.
In the event of a fault with the electric parking brake it is recommended that you contact a CITROËN dealer or a qualified workshop without delay.
SituationsConsequences
Display o
f the message "Parking brake fault" and thefollowing warning lamps:

- Automatic release is not available.

- If you attempt an automatic release, a help message is displayed on acceleration
when the parking brake is applied, prompting you to use manual release.
Displa
y of the message "Parking brake fault" and of thefollowing warning lamps:

- Secondary braking does not have full power.

- If automatic release is not available, a help message is displayed on acceleration
when the parking brake is applied, prompting you to use manual release.
Displa
y of the message "Parking brake fault" and of thefollowing warning lamps:

- Automatic application is not available: use the control lever.

- The electric parking brake can only be used manually.

- If automatic release is also not available, a help message is displayed on
acceleration when the parking brake is applied, prompting you to use manual
r
elease.
Displa
y of the message "Parking brake fault" and of thefollowing warning lamps:

- If manual application and release do not work, the control lever is faulty.

- The automatic functions must be used in all circumstances: they are
automatically reactivated in the event of failure of the control lever.

- You can no longer immobilise the vehicle with the engine running.

148
Driving





Hill start assist
System which keeps your vehicle immobilised
temporarily (approximately 2 seconds) whenstarting on a gradient, the time it takes to
move your foot from the brake pedal to the accelerator pedal. This system only operates when:
- the vehicle is completely stationary, withyour foot on the brake pedal,
- cer tain conditions of slope are met,
- with the driver’s door closed.
The hill star t assist system cannot be deactivated.
On an ascendin
g slope, with the vehiclestationary, the vehicle is held for amomentarily when you release the brakepedal:


- provided you are in first gear or neutral on
a manual gearbox,

- provided you are in position A
or M
on an electronic gearbox, Dor Mon an automatic gearbox.


Operation
On a descending slope, with the vehicle
stationary and reverse gear engaged, thevehicle is held momentarily when yourelease the brake pedal.

Operating fault

If a fault in the system occurs, these warning lamps come on, accompanied by an alert message. Contact a CITROËN dealer or
a qualified workshop to have the systemchecked.
Do not exit the vehicle while it is beingheld in the hill star t assist phase.
If you need to exit the vehicle withthe engine running, apply the parkingbrake manually then ensure that theparking brake warning lamp (and the warning lamp P
in the lever of theelectric parking brake) are on fixed (not flashing).

149
4
Driving






5-speed manual
gearbox

Engaging reverse gear
)With clutch pedal fully down, place the gear lever in neutral.)Push the gear lever to the right then backwards.
Only engage reverse gear when the vehicle is stationary with the engine at idle.
As a safety precaution and to facilitate star ting of the engine:


- always select neutral,

- press the clutch pedal.









6-speed manual
gearbox
Engaging 5th or 6thgear
)
Move the lever fully to the right to engage 5thor 6 th
gear.
Only engage reverse gear when thevehicle is stationary with the engine at idle.

As a safety precaution and to facilitate starting of the engine:


- always select neutral,

- press the clutch pedal.



Engaging reverse gear
)
Raise the ring under the knob and move
the gear lever to the left then for wards.
Failure to follow this advice may cause permanent damage to the gearbox (engagement of 3rdor 4 thgear bymistake).

150
Driving














6-speed electronic gearbox system
Six-speed electronic gearbox system which
offers a choice between the comfor t of fully automatic operation and manual gear changing. There are two driving modes:
-automatedmode for automatic control
of the gears by the gearbox, without anyaction on the par t of the driver - manualmode for sequential gear changingby the driver using the steering mountedpaddles.
In automated mode, you can temporarily take
over control of gear changing.
R
. Reverse )
With your foot on the brake, move the selector lever.N. Neutral. )
With your foot on the brake, select this
position to star t the engine.
A
. Automated mode.)
Move the selector lever to position Ato select this mode.M.Manual mode with sequential manual gear changing. )
Move the selector lever to position M
toselect this mode, then use the steeringmounted control paddles to change gear.



Gear selector lever
+.Change up paddle to the right of the steering wheel.)Pull the "+"steering mounted paddle
towards you to change up a gear.-. Change down paddle to the left of thesteering wheel.)Pull the "-"
steering mounted paddle
towards you to change down a gear.

Steering mounted control paddles


The steering mounted paddles cannotbe used to select neutral or to engageor disengage reverse gear.