2013 Citroen C4 PICASSO Owner's Manual

87
3
Comfort
System which registers the electrical settings of the driver's seat and door mirrors. It enables you to store and recall two positions using the buttons on the side of the driver's seat.
Storing driving positions
Storing a position
Usin
g buttons M / 1 / 2
) Switch on the ignition. )
Adjust your seat and the door mirrors. )
Press button M
, then press button 1or 2
within four seconds.
An audible signal indicates that the position
has been stored.
Storing a new position cancels the previousposition.

Recalling a stored position

I
gnition on or engine running
)
Press button 1or 2to recall the corresponding position.
An audible signal confirms that adjustment
is complete.
You can interrupt the current movement b
ypressing button M, 1
or 2
or by using one of theseat controls.
A stored position cannot be recalled while driving.
Recalling stored positions is deactivated
45 seconds after switching off the ignition.

88
Comfort
Additional adjustments
Head restraint height and angle (depending on version)
The head restraint is fitted with a frame with notches which prevents it from lowering; this isa safety device in case of impact.The adjustment is correct when the upper edge of the head restraint is level with the
top of the head. Never drive with the head restraints removed; they must be in place and adjusted correctly.
)To raise a head restraint, pull it upwards.)To lower the head restraint, press the lug Aand the head restraint at the same time.)To a djust the angle of the head restraint, tilt its lower part for wards or rear wards.


Removing a head restraint
)
To remove the head restraint, press the lug Aand pull the head restraint upwards. )
To put the head restraint back in place,engage the head restraint stems in the openings keeping them in line with the seat
back and press the lug A at the same time.


Comfort head restraints

Depending on version, you can fold the sides to
obtain a more comfor table position.

89
3
Comfort
)Press the control to obtain the desired lumbar support.




Electric lumbar adjustment
You can deactivate the massage
function at any time by pressing this
switch, its indicator lamp goes off.



DeactivationActivation
Massage function
This function provides the front occupants
with a lumbar massage. It only operates when
the engine is running or in STOP mode of the Stop & Start system.
)
Press this switch.




Adjustment of intensity
Press this button to select one of
the two levels of massage intensityoffered.

Its indicator lamp comes on and the massagefunction is activated for a period of 1 hour.
During this time, massage is performed in6 cycles of 10 minutes (6 minutes of massage followed by 4 minutes break).
After one hour, the function is deactivated, the
indicator lamp goes off.

90
Comfort
Electric leg rest
Manual passenger seat
)Press the front or rear part of the control tounfold or fold away the leg rest.
The movement stops when you release the
control.







Heated seats control
)Use the adjustment wheel to switch on and select the level of heating required:

0:
Off. 1:Low.2:Medium. 3:
High.
With the en
gine running, the front seats can be heated separately.
Before operating the leg rest, ensurethat nothing could inter fere with itsmovement.


Electric passenger seat
)
Push the control forwards or backwards to unfold or fold away the leg rest.
The movement stops when you release thecontrol.

91
3
Comfort
Front armrest

Height adjustment
)Fully lower the armrest. )Raise it to the required position (low,
intermediate or high). )Once in the high position, lift to release it and return it to the low position.


Comfor t system for the driver and front passenger.

92
Comfort











Second-row seats


Forwards-backwards adjustment
)Raise the lever A
, located at the front of
the seat cushion, and adjust the seat to the
desired position. The
3 seats in the 2nd row are independent of each other and are all the same width. Their backrests can be folded to vary the load space in the boot.

93
3
Comfort
)Pull the strap B and guide the seatrearwards.
The backrest reclines and the seat base pivots
slightly.


"Comfort" position


Returning the seat to the initialposition
)Pull the strap B
and guide the seatforwards.

Super vise any movements of seats when made by children.
To remove it:
- move the head restraint to the high position,
- press lu
g Apulling the head restraint upwards at the same time. Th
e rear head restraints can be removed and have two positions:
- high, position for use,
- low, storage position. To raise a head restraint, pull it upwards.
To lower it, press lug A
then the head restraint.
Rear head restraints

Never drive with the head restraintsremoved; they must be in place and correctly adjusted.
T
o refit it:
- engage the rods of the head restraint in the
openings keeping then in line with the seat
back.

Comfort head restraints

Depending on version, the sides can be folded
to obtain a more comfortable position.

94
Comfort
Flat floor
Folding a seat
From the outside) Pull firmly upwards on strap C, as indicated
by the arrow, to unlock the seat; keep
pulling until the seat is fully folded.
Push the seat backrest gently forwards so that the backrest folds onto the seat cushion. The assembly lowers onto thefloor. From the boot, when loadin
g for example You can fold the second-row seats from theboot, after first folding the third-row seats. )Pull on the strap Dto release the seat in
question then push forwards lightly on the backrest.
To avoid any damage to the mechanism,
the strap D unclips if too much force isapplied. Simply clip it in place again for thesystem to be operational again.
)Place the seats in the fully back position. Each seat can be
folded onto the floor to vary
the the space available in the boot.