2013 AUDI Q5 buttons

Programming the transmitter (version B)
Applies to vehicles: with Horne link
Fig. 15 1 Distance between the radiator gr ille and the
hand transmitter
P rogrammin g: ph ase 1 on the control unit
1. Sw itch on the ig nit ion (do no t start the
engine) .
2. Press and hold both of the outer Home­
Link buttons
r=>page 135, fig. 149 until
the LED @ turns off completely (about
20
seconds). Th is procedure clears the stand­
ard codes that were set at the factory and
does
n ot need to be repeated agai n to
p rog ram the other buttons.
3. Briefly press the Homelink button that
you would li ke to prog ram .
4 . Wai t unti l the LED @ beg ins to b link
q ui ckly. The Home Link modu le wi ll now
remai n in learning mode for
5 minutes .
5. Now stand in front of your vehicle with
the original hand transmitter for the ga­ rage door opener or for the device that
you would like to allocate to the Home­
Link button.
Programming: pha se 2 on th e radiator
grille
6 . Hold the orig inal hand transmitter some­
what towa rds the center of your vehicle 's
radiato r grille r=>
fig. 151.
7. Now act ivate (p ress) t he hand transmit­
ter.
8 . Pay a ttention to the tu rn signals for you r
vehicle when activating the ha nd trans­
mitter . If t he emergency flashers blink
three times, the programming was suc­
cessful. If the emergency flasher only
bli nks one t ime, the 5 minute t ime limit
Homelink ® 13 7
for the adaptation has expired or the pro ­
gram ming was unsuccessful. Repeat the
programming from step 3 on the controls
or select another distance from the radia­
tor grille.
9. If the garage door or other devices sti ll
fail to be activated w it h the Homelink
control buttons after p rogramming is
comple ted, it is possib le tha t these sys­
tems might be working with a rolling code
ins tead of the normal fixed code .
A Roll­
ing code programming must be per ­
formed
r=> page 138 .
Program the rema ining two buttons a ccord ing
to the instructions mentioned above . Beg in
similar ly w ith the 3rd step if the program ­
ming connection was successful for t he first
button.
Remote con tro l units fo r garage door opene rs
in Canada are set to stop transmitting radio
frequency signa ls after two seconds . This time
may not be suffic ient for the Homelink sys­
tem to learn the radio frequency signa l. Per­
form all other steps as described above.
Erasing the buttons
.,. Switch o n the ignition (do not start the en­
gi ne).
.,. Press and hold both of the outer buttons
until the LED @ turns off completely (about
20 seconds) to erase all of the buttons si­
m ultaneously .
.,. Programmed buttons cannot be erased ind i­
vidua lly. Reprogram the buttons if necessa­
ry .
Reprogramming the buttons
.,. Switch on the ignition (do not start the en­
gine) .
.,. To reprogram an individua l butto n, press
and hold the button unt il the LE D @ starts
to f lash quickly (after abo ut ten seconds) .
Release t he but ton imme dia tely. The Home­
L ink module will now remain in learning
mo de for 5 minutes.
.,. Continue with step 5.

138 Homelink®
-The required dista nce between the hand
transmitter and the HomeLink module in
the radiator grille
c:> fig. 151 depends on
the system that you are programming.
- Depend ing on the model of the garage
door opener, you may need to release the
button on the remote and press it again
when programming . When p rogram­
ming a new dev ice, keep the button
pressed for a t least 15 seconds befo re
trying again wi th the transmitte r in a dif­
ferent pos it ion. W atch out fo r the emer­
gency flasher during that time .
Programming the rolling code
Applies to vehicles: with Home link
Additionally, a rolling code programming for
the HomeLink universal remote control is re­
quired for some systems .
Identifying the rolling code
.. Press the prev ious ly programmed Homelink
button aga in and hold i t down .
.. Look at the LED@ c:>
page 135, fig. 149 . If
the LED blinks quickly , the features, s uch as
the garage door o pener, are equipped with
the rolling code .
.. Program the roll ing code as fo llows:
Act ivating the garage door opener motor
unit
.. Locate the sett ing button on the garage
door opener motor unit . The exact location
and co lor of the b utton may vary depending
on the garage door opener ma nufacturer .
.. Press the sett ing button on the garage door
opener motor unit (usually th is w ill act ivate
a "se tt ing light d isp lay" on the moto r unit).
Now you w ill have abo ut
30 se conds ti me to
p erfo rm the Home Link bu tton programming
on the cont ro ls.
Programming on the controls
.. Press the Home L ink button that was already
programmed and hold for two seconds . ..
To end ro lling code programm ing, p ress and
hold t he Home link button for two seconds
aga in .
.. The Homelink button may need to be press­
ed a t hird t ime to end the adjus tment proce­
dure for some garage door openers .
After the controls have been programmed, the
garage door opener s hou ld recogni ze the
Homelink signa l and operate when the Home­
Li nk button is pressed . N ow you may program
the o ther buttons as needed .
(D Tips
-Programmi ng the rolling code can be
performed quicke r and more easily with
the help of a second person .
- If d iff iculties should ar ise when pro­
gramming the rolling code, consult the
op erating instructions fo r th e garage
door opener or o ther dev ices for po ssible
s o lu tions.

& WARNING
Too much undercoating in the wrong pla­
ces can cause a fire.
- Do not apply additional undercoating or
rustproofing on or near the exha ust
manifold, exhaust pipes, cata lytic con­
verter or heat shie lds . Wh ile driving, the
substance used for undercoating could overheat and cause a f ire.
- Always read and heed all WARNINGS and other information
c:> page 216.
Exhaust tail pipes
-
Road sa lt and other corros ive materia ls will
damage the mater ial in the exhaust tail p ipes
if they are not cleaned regula rly . Do not clean
the ta il p ipes with whee l cleaner, paint polis h,
chrome polish or othe r abrasive cleane rs.
C lean the tail p ipes wi th car care prod ucts
that are s uitab le for stain less stee l.
Your authori zed Audi dealer can provide clean­
in g p roducts t hat have been tested and ap­
p roved for you r vehi cle.
Care of interior
Radio and MMI* display
.,. Clean the d isp lay w ith a soft clea n cloth and
an LCD cleane r.
The display can be cleaned w ith a professio­
na lly available "LCD cleaner". The cloth shou ld
be slightly dampened with the clean ing flu id
to clean the display .
(D Note
To avoid scratching the display, you should
never clean it dry .
MMI control console
Applies to vehicles: with MMI
.. First clean the MMI control console with a
brus h to remove dust from the hous ing .
.,. The n w ipe the MMI con tro l c onso le w ith a
cl ean, soft, s ligh tly damp cloth .
Cleaning and protec tion 223
The M MI contro l console sho uld be cleaned
with a brush first so that no dirt is t rapped be­
tween the buttons and the housing . We rec­
ommend giving the MMI control conso le a fi ­
nal wipe with a cloth moistened with water
and dish washing detergent .
(D Note
To prevent damage, make s ure that no flu­
i d ever gets into t he MMI contro l conso le.
Aluminum trim
Use only neutral-pH products to remove spots
and deposits from aluminum surfaces .
Chrome care products a nd a lkaline cleaners
will attack a luminum surfa ces and ca n dam­
age them over t ime .
& WARNING ~
Always read and heed all WARN INGS and
other info rmation
c:> page 216.
Fabrics and fabric coverings
Fabrics and fab ric coverings (e.g . seats, door
trim pane ls, etc .) sho uld be cleaned at regular
intervals w ith a vacuum cle aner. This removes
su rface dirt particles which could become em­
bedded in the fabric through use . Steam
cleaners sho uld not be used , because the
steam te nds to p ush the dirt deeper into the
fabric and lo ck it the re.
Normal cleaning
Generally, we recommend us ing a soft sponge
o r a lint -free microfibe r clo th to t he clean fab ­
r ic. B rushes s hou ld only be used for carpets
and floo r mats, since othe r fabr ic surfa ces
cou ld be harmed by br ushes.
Normal su rface stains can be cleaned using a
comme rc ially availab le foam cleaner . Spread
the foam o n the su rface of t he fabric with a
soft sponge and wo rk it in gently . D o no t satu ­
ra te the f abric. Then pat the foam dry using
absorbent, dry cloths (e .g . m icrofi ber cloth)
and vac uum it after it has dried compl etely .
Ill>
•
•

Index 301
-----------------------------------.......
Automatic Shift Lock (ASL) . ... .. .. .. . 124
Automatic transmission .......... .... 123
Automatic S hift Lock (ASL) . .. .. .. .. . 124
Driving .. .. ............. .. .. .. ... 125
E mergency mode ......... .. .. .. .. . 128
E me rgency release . . . . . . . . . . . . . . . . . 128
Hill descent control .... ... .. .. .. .. . 126
Kick -down . ..... ...... ... .. .. .. ... 127
Manual sh ift program ..... .. .. .. .. . 127
Removal lock (ignition key) . .. .. .. .. .. 83
Selector lever ......... ...... .... .. 123
Shift buttons .... .. ...... .. .. .. .. . 127
Automatic wipe/wash system . . . . . . . . . . 54
Auto Safety Hotline ........ .. .. .. .. . 146
AUTO (climate contro l) . . . . . . . . . . . . . . . . 80
Average speed . . . . . . . . . . . . . . . . . . . . . . . 23
Avoid damag ing the vehicle ...... . ... . 206
B
Bass box .. ............ ...... .... .. 270
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Battery locat ion inside the luggage com-
partment .. ............. .... .. .. . 244
C harging . . . . . . . . . . . . . . . . . . . . 105 , 245
Important war nings when working on
the battery . . . . . . . . . . . . . . . . . . . . . . . 244
Jump starting ............... ... ... 284
L ow . .. .. .. ................. .. .. . 203
Replacing the batte ry ..... .. .. .. .. . 246
State of charge . .. ..... ... .. .. .. ... 203
Voltage .... .... ...... ... .. .. .. .... 34
Winter operation . ..... ... .. .. .. .. . 243
Working on the battery . . . . . . . . . . . . . 244
B efore driving ............. .... .. .. . 139
Bio-ethanol (Fuel) .... ...... .. .. .. .. . 229
Blended gasoline ... .... ... .. .. .. ... 228
B lower (climate control) . . . . . . . . . . . . . . . 80
Body cav ity sealing ......... .. .. .. .. . 222
B ooster seats .. .. .. .... ... .. .. .... . 186
Brake flu id
Changing the brake flu id .... ... ... .. 243
C hec kin g the bra ke fluid level . .. .. .. . 242
Reservoir .. .. ........... .. .. .. ... 24 2
Wha t is the cor rect brake flu id leve l? . . 24 2
What should I do if the brake flu id warn -
ing light comes on? .... ... .. .. .. .. . 242 Brake system .
..... ... .. .. ..... ... .. 242
Anti- lock b rake system . . . . . . . . . . . . . . 17
Brake assist system .. .. ..... ... .. .. 197
Brake booster .. .. ................. 200
Brake fluid .. .. .. .... ............. 242
B rake fluid specifications fo r refill and re ­
placeme nt . . . . . . . . . . . . . . . . . . . . . . . 243
B ra ke light defective . . . . . . . . . . . . . . . . 33
B ra ke pads .. .. .. .. . .............. 205
El ec tromechan ical par king br ake . .. .. . 88
General informa tion . ... .... ... .. .. 2 00
How does moist ure or road salt affect the
brakes? ... .. .. .. .. . ... ...... ... .. 200
Malfunction . . . . . . . . . . . . . . . . . . . . . . . 29
Warning/ind icator lights ............ . 18
Wor n brake pads symbol . . . . . . . . . . . . . 33
Braking guard . . . . . . . . . . . . . . . . . 107, 113
Messages . . . . . . . . . . . . . . . . . . . . . . . . 114
Settings .. .. .. .. .. ............... 114
Switching on and off ........... .. .. 114
B reak-in per iod .. .. .. . .............. 205
B rake pads .. .... .. . .. .. ..... ... .. 205
Tires ... .. .. .... .. . .. .. ..... ... .. 205
B reakove rangle . .. .... ........... .. 209
Bu lbs ........ .. ...... ............. 283
C
Californ ia Proposition 65 Warning ... .. 234
Battery spec ific . . . . . . . . . . . . . . . . . . . 245
C ap aci ties .. .. .. .. .... ........... .. 292
Car care .......... .. ..... .......... 216
E xterior . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Inte rio r ... .. .. .. .. ............... 223
Plast ic and vinyl .. .... ............. 220
Cargo a rea
refer to Loading the l uggage compart -
ment . ...... .. .... .......... ..... 145
Cargo floor . . . . . . . . . . . . . . . . . . . . . . . . . 70
Cata lytic converter . .... ......... .... 2 06
Center armrest Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . 66
Storage compa rtment .. .. .. ... ... .. . 66
Certification .. .. .. .. ............... 298
Changi ng
A flat t ire ... .... .. . .. .. ..... ... .. 274
A whee l ... .. .... .. . .. .. ..... ... .. 274
Engine oi l ... .... .. . .. .. ..... ... .. 239
•
•

310 Index
Selector lever ..... ..... ... .. .. .... . 123
Emergency release . . . . . . . . . . . . . . . . . 128
Service and disposal
Safety belt p retens ioner . .. .. .. .. .. .
156
Service interval d isp lay ....... ... .. .. .. 22
Service pos ition for windshield wipers .. . 55
SET button . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
Shift buttons .............. .. .. .... . 127
Ship transport ...................... 106
Side airbags
Descr ipt ion . .............. ... .. ...
172
H owtheywork .................... 174
Side assist
Ac tiva ting and deactivating . .. .. .. .. .
118
Adjusting the brightness ............ 118
C leaning sensors .............. .... 2 19
D escr ipt ion ... ........... .. .. .... . 116
Sensor range . . . . . . . . . . . . . . . . . . . . . 117
Side curta in airbags ........ .. .. .. .. . 175
Descr ipt ion . .............. ... .. ... 175
H owtheywo rk .................... 176
Safety instructions ......... ... .. .. . 177
Side marker lights ................... 49
Snow chains .... ... .... ... .. .. .... . 264
Socket .. ... ................... ... .. 75
Sound system display
Driver information display . . . . . . . . . . . .
20
Sources o f informat io n about c hild re-
straints and their use .. ... .. .. .. .... .
19 6
Speedometer ... .... ...... .. .. .. .. .. 13
Speed rating letter code ..... .. .. .. .. . 260
Speed warn ing system ................ 93
Start-Stop-System . . . . . . . . . . . . . . . . . . . 91
Eng ine does not switched off ... ...... 92
E ng ine starts automatically .......... 92
Ind icator lights . . . . . . . . . . . . . . . . . . . . 92
M essages . . . . . . . . . . . . . . . . . . . . . . . . . 93
S tarting/stopping the eng ine . .. .... .. 92
Sw itching off/on . ..... ... .. .. .... .. 93
START ENGINE STOP button (Conven ience
key) . . . . . . . . . . . . . . . . . . . . . . . . . . .
86, 87
Starting from rest .......... .. .. .... .. 90
Starting off with a tra ile r .. .. .. .. .. .. . . 90
Starting the eng ine . . . . . . . . . . . . . . 83, 86
Start ing (engine) . . . . . . . . . . . . . . . . . . . . 98
Stee ring
E lectromechanical power assist . . .
201, 0
Indicator light ... ... .. ..... ... .. .. 201
Locking the steering ............... . 83
Malfunction . . . . . . . . . . . . . . . . . . . . . . . 31
Manually adjusting the steering wheel . . 83
also refer to Electromechanical power as-
s ist ......... ....................
201
Steering wheel column
Adjusting manually .............. .. .
83
Steps for determin ing correct load limit . 257
Stopping the eng ine . . . . . . . . . . . . . . 85, 87
Stopping (engine) ... .............. .. . 98
Storage ............................ 76
Cu pholder door pockets . . . . . . . . . . . . . . 7 4
G love compartment . . . . . . . . . . . . . . . . .
76
Sun shade ........ .. .............. .. 54
Sun visors .. .. .. .. .. ........... .... . 54
Supplementa ry (climate contro l) ... .... . 82
Switches
Emergency flashe rs . . . . . . . . . . . . . . . . .
52
Symbols
Red ..............................
28
Yellow .... .... .. ............. .... . 31
T
Tachometer ..... .. ............. .... . 11
Technical modifications .......... .... 298
Tether anchors .. .................. . 194
Tether strap . ..... ... .. ..... ... .. .. 194
T he first 1,000 miles (1,500 km) and after -
wa rds .............................
205
Tie-down rings . . . . . . . . . . . . . . . . . 68, 146
tiptronic ... .... .. .. ... ..... ... .. .. 123
Automatic Shift Lock (ASL) ... .... . .. 124
Driving . .. .. .. .. ............. .. .. 125
Emergency mode .... .......... .. .. 128
Hill descent control .............. .. 126
K ick -down ........................ 127
Manual shift prog ram .. ....... ... .. 127
Se lector lever .. .. ............. .. .. 123
Tire Mobility System . . . . . . . . . . . . 104, 272
T ire pressure . ... .. .. .... .... ... .. .. 254
T ire pressure mon itoring system ....... 266
Loss of ai r pressure . . . . . . . . . . . . 16, 267