2012 YAMAHA CYGNUS 125 set clock

1
2
3
4
5
6
7
8
9
3-3
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
engine is not working correctly. If this
occurs, have a Yamaha dealer check
the self-diagnosis system.
The electrical circuit of the warning
light can be checked by turning the
key to “ON”. The warning light should
come on for a few seconds, and then
go off.
If the warning light does not come
on initially when the key is turned to
“ON”, or if the warning light remains
on, have a Yamaha dealer check the
electrical circuit.
EAU11601
SpeedometerZAUM00**
RESET
SELECT
1
1. SpeedometerThe speedometer shows the riding
speed.
When the key is turned to “ON”, the
speedometer needle will sweep once
across the speed range and then re-
turn to zero in order to test the electri-
cal circuit.
EAUT1957
Multi-function display
EWA14431
WARNING
Be sure to stop the vehicle before
making any setting changes to the
multi-function display. Changing
settings while riding can distract
the operator and increase the risk
of an accident.ZAUM00**
RESET
SELECT
1
2
3
4
5
6
1. Oil change indicator “7”
2. Odometer
3. Fuel meter
4. “RESET” button
5. “SELECT” button
6. ClockThe multi-function display is equipped
with the following:●
an odometer
4P9-F8199-E5_CS.indd 3-34P9-F8199-E5_CS.indd 3-3
2011/09/06 14:18:392011/09/06 14:18:39
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
3-4
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS●
a tripmeter (which shows the dis-
tance traveled since it was last
set to zero)
●
an oil change tripmeter (which
shows the distance traveled since
the last engine oil change)
●
an oil change indicator (which
flashes when the engine oil
should be changed)
●
a clock
●
a fuel meter
TIP●
When the key is turned to “ON”,
all segments of the display come
on for a few seconds. During this
time, the multi-function display is
performing a self-test.
●
Be sure to turn the key to “ON”
before using the “SELECT” and
“RESET” buttons.
Odometer, tripmeter and oil change
tripmeter modes
Pushing the “SELECT” button switch-
es the display among the odom-
eter mode “ODO”, the tripmeter mode
“TRIP” and the oil change tripmeter
“OIL CHANGE TRIP” in the following
order:
ODO → TRIP → OIL CHANGE TRIP
→ ODO
OdometerTIPIf the odometer indicates “-----”, have
a Yamaha dealer check the multi-
function display, as it may be faulty.
Tripmeter
To reset the tripmeter, select it by
pushing the “SELECT” button until
“TRIP” is displayed, and then push the
“RESET” button at least 1 second.TIPIf the tripmeter indicates “-----”, have
a Yamaha dealer check the multi-
function display, as it may be faulty.
Oil change tripmeter
To reset the oil change tripmeter, se-
lect it by pushing the “SELECT” but-
ton until “OIL CHANGE TRIP” is dis-
played, and then push the “RESET”
button at least 3 seconds.
Push the “SELECT” button again to
start the oil change tripmeter; the dis-
play changes to the ODO mode.
Oil change indicator “7”
This indicator flashes at the initial
1000 km (600 mi), then at every 3000
km (1800 mi) thereafter to indicate
that the engine oil should be changed.
After changing the engine oil, reset
the oil change tripmeter.
If the engine oil is changed before
the oil change indicator flashes (i.e.
before the periodic oil change interval
has been reached), the oil change
tripmeter must be reset after the
oil change for the next periodic oil
change to be indicated at the correct
time.TIP●
If the oil change tripmeter is reset
before the initial 1000 km (600
mi), the next periodic oil change
4P9-F8199-E5_CS.indd 3-44P9-F8199-E5_CS.indd 3-4
2011/09/06 14:18:392011/09/06 14:18:39
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
3-5
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
interval will be at every 3000 km
(1800 mi) thereafter.
●
If the oil change tripmeter in-
dicates “-----”, have a Yamaha
dealer check the multi-function
display, as it may be faulty.
Clock
To set the clock:
1. Push the “SELECT” button and
“RESET” button together for at
least two seconds.
2. When the hour digits start flash-
ing, push the “SELECT” button to
set the hours.
3. Push the “RESET” button, and
the first minute digit will start
fl ashing.
4. Push the “SELECT” button to set
the fi rst minute digit.
5. Push the “RESET” button and
the second minute digit will start
fl ashing.
6. Push the “SELECT” button to set
the second minute digit.
7. Push the “RESET” button and
then release it to start the clock.Fuel meter
The fuel meter indicates the amount
of fuel in the fuel tank. The display
segments of the fuel meter disappear
towards “E” (Empty) as the fuel level
decreases. When “
” starts flashing,
refuel as soon as possible. When the
key is turned to “ON”, all of the display
segments of the fuel meter will appear
for a few seconds, and then shown
actual fuel level.
EAU12349
Handlebar switchesLeftZAUM00**
3 1
2
1. Dimmer switch “%/&”
2. Turn signal switch “4/6”
3. Horn switch “*”RightZAUM00**
1
1. Start switch “,”
4P9-F8199-E5_CS.indd 3-54P9-F8199-E5_CS.indd 3-5
2011/09/06 14:18:392011/09/06 14:18:39
Process BlackProcess Black