1
2
3
4
5
6
7
8
9
6-29
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENTRear turn signal light bulb
1. Remove the tail/brake light lens
by removing the screws.
2. Remove the turn signal light lens
by removing the screws.
3. Remove the burnt out bulb by
pushing it in and turning it coun-
terclockwise.
4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Install the turn signal light lens by
installing the screws.
6. Install the tail/brake light lens
by installing the screws.
NO-
TICE:
Do not overtighten the
screws, otherwise the lens may
break.[ECA10681]EAUT1963
Replacing an auxiliary light
bulbZAUM00**
12
1. Auxiliary light bulb
2. SocketThis model is equipped with two aux-
iliary lights. If an auxiliary light bulb
burns out, replace it as follows.
1. Remove panel B. (See page 6-7.)
2. Remove the auxiliary light socket
(together with the bulb) by turning
it counterclockwise.
3. Remove the burnt out bulb by
pulling it out.
4. Insert a new bulb into the socket.
5. Install the auxiliary light socket
(together with the bulb) by turning
it clockwise.
6. Install the panel.
EAU25861
TroubleshootingAlthough Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting chart
represents a quick and easy pro-
cedure for checking these vital sys-
tems yourself. However, should your
scooter require any repair, take it to a
Yamaha dealer, whose skilled techni-
cians have the necessary tools, expe-
rience, and know-how to service the
scooter properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
EWA15141
WARNING
When checking the fuel system, do
not smoke, and make sure there
are no open flames or sparks in
4P9-F8199-E5_CS.indd 6-294P9-F8199-E5_CS.indd 6-29
2011/09/06 14:18:412011/09/06 14:18:41
Process BlackProcess Black
1
2
3
4
5
6
7
8
9
8-1
SPECIFICATIONS SPECIFICATIONS
EAU50915
DimensionsOverall length
1855 mm (73.0 in)
Overall width
685 mm (27.0 in)
Overall height
1130 mm (44.5 in)
Seat height
785 mm (30.9 in)
Wheelbase
1295 mm (51.0 in)
Ground clearance
113 mm (4.45 in)
Minimum turning radius
1900 mm (74.8 in)WeightCurb weight
120 kg (265 lb)EngineEngine type
Air cooled 4-stroke, SOHC
Cylinder arrangement
Single cylinder
Displacement
125 cm
3
Bore x stroke
52.4 x 57.9 mm (2.06 x 2.28 in)
Compression ratio
10.00 :1
Starting system
Electric starter and kickstarter
Lubrication system
Wet sump
Engine oilRecommended brand
YAMALUBE
Type
SAE 10W-30, 10W-40, 10W-50, 15W-40,
20W-40 or 20W-50
–20 –10 0
1020 30 40 50 ˚C 10 30 50 70 90 110 0 130 ˚F
SAE 10W-30
SAE 15W-40SAE 20W-40SAE 20W-50
SAE 10W-40SAE 10W-50
Recommended engine oil grade
API service SG type or higher, JASO
standard MAEngine oil quantityPeriodic oil change
0.90 L (0.95 US qt, 0.79 Imp.qt)Final transmission oilType
SAE 10W-30 type SE motor oil
Quantity
0.11 L (0.12 US qt, 0.10 Imp.qt)Air lterAir fi lter element
Wet elementFuelRecommended fuel
Regular unleaded gasoline onlyFuel tank capacity
7.4 L (1.96 US gal, 1.63 Imp.gal)
Throttle bodyID mark
4P91 00
Manufacturer
MIKUNISpark plug(s)Manufacturer/model
NGK/CR7E
Spark plug gap
0.7-0.8 mm (0.028-0.031 in)ClutchClutch type
Dry, centrifugal automaticTransmissionPrimary reduction ratio
1.000
Secondary reduction ratio
9.744 (38/13 40/12)
Final drive
Gear
Transmission type
V-belt automaticChassisFrame type
Backbone
Caster angle
27.00 degree
Trail
90 mm (3.5 in)Front tireType
Tubeless
4P9-F8199-E5_CS.indd 8-14P9-F8199-E5_CS.indd 8-1
2011/09/06 14:18:412011/09/06 14:18:41
Process BlackProcess Black
