2012 SSANGYONG NEW ACTYON SPORTS ignition

05-10
9) Starting System
The engine electrical system includes the battery, the ignition, the starter, the generator, and all
the related wiring.
Diagnostic tables will aid in troubleshooting system faults. When a fault is traced to a particular
component, refer to that component section of the service manual.
The starting system circuit consists of the battery, the starter motor, the ignition switch, and all the
related electrical wiring.
All of these components are connected electrically.

12-10
4) Recovery of Set Speed (RESUME)
Even if the cruise control is cancelled, the previous set cruise speed can be recovered by pulling
up the cruise control lever when the current vehicle speed is over 36 km/h without an acceleration
intervention. But if you turn off the ignition switch, the memorized set speed is cleared and you
cannot recover the previous set speed.
But the driver should know the previous set speed to react to the changed vehicle speed
properly. If the vehicle speed increases abruptly, depress the brake pedal to adjust the vehicle
speed properly.

12-12
Do not move the shift lever to Neutral position while driving with the cruise control turned on.
Otherwise, it may result in system malfunction or accidents.
Always be prepared to use the brake or accelerator pedal for safe driving while the cruise
control system is running.
The actual speed can be different from the set speed momentarily when driving on a uphill
or downhill. So, it is recommended to disable the cruise control function on a uphill or
downhill. hen driving on a steep hill use the engine brake and foot brake properly to protect
the vehicle system and for a safe driving.
Ensure that the safe distance is maintained and use the brake pedal if needed. 1.
2.
3.
4.
(1) Abnormal Cancellation of the Cruise Control
When the rapid deceleration is applied without braking.
When the rapid acceleration is applied without acceleration pedal intervention.
When the cruise control lever is faulty.
When the brake switch and the brake light switch input signal are implausible. 1.
2.
3.
When the cruise control function is cancelled abnormally or intermittent problems occur, stop the
vehicle and turn off the ignition switch and remove the key to reset the system. After a while, turn
on the ignition switch again to operate the cruise control system.

02-38710-01
1. PERFORMANCE AND SPECIFICATIONS
1) Rated Load & Input Signals
Rated Load ▶
NO. Item Rated Load
1 Chime bell / Buzzer DC 12V 350 mA (Inductive load)
2 Front room lamp DC 12V 16W (Lamp load)
3 Rear room lamp DC 12V 8W (Lamp load)
4 Ignition key illumination DC 12V 1.2W (Lamp load)
5 Seat belt indicator DC 12V 1.2W (Lamp load)
6 Parking brake warning lamp DC 12V 1.2W (Lamp load)
7 Door ajar warning lamp DC 12V 1.2W (Lamp load)
8 Door lock relay DC 12V 200 mA (Inductive load)
9 Door unlock relay DC 12V 200 mA (Inductive load)
10 Horn relay DC 12V 260 mA
11 Tail lamp relay DC 12V 200 mA (Inductive load)
12 Hazard warning lamp relay DC 12V 200 mA (Inductive load)
13 Power window relay DC 12V 200 mA (Inductive load)
14 Rear defogger relay DC 12V 200 mA (Inductive load)
15 Wiper LOW relay DC 12V 200 mA (Inductive load)
16 Wiper HIGH relay DC 12V 200 mA (Inductive load)
17 Front washer motor DC 12V 1.5A
18 Head lamp relay DC 12V 750 mA (Inductive load)
19 Front defogger relay DC 12V 200 mA (Inductive load)
20 Mirror lock relay DC 12V 200 mA (Inductive load)
21 Mirror unlock relay DC 12V 200 mA (Inductive load)

02-8
2) Operation Logic
▶Wiper MIST and Front Washer Coupled Wiper
The wiper relay is turned on at 0.3 seconds after from the time when the washer switch is
turned on for 0.1 to 0.59 seconds with the ignition switch "ON".If the wiper parking
terminal gets off, the wiper relay is turned off. -
The wiper relay is turned on at 0.3 seconds after from the time when the washer switch is
turned on for more than 0.6 seconds with the ignition switch "ON". The wiper relay gets on
3 times immediately after turning off the washer switch. -

02-10
▶Auto Washer and Wiper Switch (AFW)
When the auto washer switch is turned on with the ignition switch "ON" and the INT switch
"OFF", the washer motor output gets ON for 1 second. If the system recognizes the output
signal, the wiper relay output gets ON during 4 cycles and the washer motor output gets
ON for 1 second. Then, the wiper relay output gets OFF after 3 cycles. -

02-138710-01
Rain sensing unit
(AUTO light integrated type)
▶INT Switch Auto Position Reminder (Power-Up Reminder Wiper)
When turning off and on the auto INT switch, the system drives the wiper motor through
LOW relay regardless of communication with rain sensor.
When turning the INT-AUTO switch from the "OFF" to "ON" position with the ignition switch
in the "ON" mode, the LOW relay operates to drive the wiper motor for 1 cycle, regardless
of the rain sensor communication.
After that, when turning the INT-AUTO switch from the "OFF" to "ON" position, the LO
W
relay operates to drive the wiper motor for 1 cycle only if data from the rain sensor
indicates rain drops. -
-
Multifunction wiper switch:
AUTO and sensitivity control
A sensor that emits infrared rays through LED
and then detects the amount of rain drops by
receiving reflected rays against sensing section
(rain sensor mounting section on the
windshield) with photodiode (auto light sensor
integrated type)AUTO: Wiper operates automatically by rain
sensor
FAST↔SLOW: Auto delay/Auto speed control. A
position that can control sensitivity against rains
on the windshield and transmits wiping demand
signal accordingly

02-14
▶Washer Coupled Wiper in Rain Sensing Mode
The washer coupled wiper is operated when receiving the washer switch input with the
ignition switch and the INT-AUTO switch "ON" in the rain sensing mode. At this moment,
the communication with the rain sensor is overridden. However, a washer input is overridden
if there is an output for continuous operation.
The operation data is sent to the rain sensor even during the washer coupled wiper's
operation. -
-