2012 SSANGYONG NEW ACTYON SPORTS ignition

02-498710-01
Automatic Hazard Warning Lamp Switch (SHP: Safety Hazard Protection) ▶
When the automatic hazard warning lamp switch is pressed for approx. 0.1 to 0.59
seconds, the hazard warning lamp blinks 3 times at an interval of 0.35 seconds.
When the automatic hazard warning lamp switch is pressed for approx. 0.6 seconds or
longer, the hazard warning lamp blinks 10 times at an interval of 0.35 seconds.
This function is only available when the ignition key is in the "ON" position.
If the ignition key is turned to the "OFF" position during this function is activated, this
function is immediately deactivated.
If the system receives signals for the turn signal lamp operation during this function is
activated, this function is immediately deactivated.
While the turn signal lamp signals are already inputted, pressing the automatic hazard
warning lamp switch does not activate the automatic hazard warning lamp function. 1.
2.
3.
4.
5.
6.
Automatic hazard warning lamp switch ▶
Press briefly (0.1 ~ 0.59 seconds): The hazard
warning lamp blinks three times.
Press and hold (more than 0.6 seconds): The
hazard warning lamp blinks ten times. ·
·

02-52
Specification of Receiver ▶
Operating requirements 1.
You should remove the ignition key. -
Code registration requirement 2.
You can register the code only using the diagnostic device. -
Transmitter code registration 3.
You can register up to 5 transmission codes to the remote control key.
The receiver does not output the received code during registration.
Connect the device to the diagnostic terminal.
The code can be registered only by the panic signal from the transmitter.
(Other switches (LOCK/UNLOCK/ESCORT) can't code.) a.
b.
c.
Remote Door Lock ▶
All doors are locked when briefly pressing the door LOCK burron on remote control key (less
than 0.5 seconds).
The system outputs LOCK signal immediately after receiving the door lock message from the
remote control key. The system activates the theft deterrent mode when all doors are locked
while they are fully closed (the hazard warning lamps blink twice.). 1.
2.

02-56
Outside rearview mirror folding/unfolding control ▶
If you press the folding/unfoling switch with the ignition switch in "ON" position, the outside
rearview mirror is folded or unfolded depending on the previous status. At this time,
folding/unfolding outputs are maintained for about 15 to 17 seconds.
Even though the ignition switch is turned to "OFF" position during folding/unfolding output,
the output continues on for remaining time.
When removing and refitting the battery, the first switch input folds the mirror.
If you turn the ignition switch to the "OFF" from "ON" position, operating time is extended by
60 seconds. Unlikely the previous model, opening the front door does not affect the
extension time. (i.e., opening/closing the front door is irrelevant)
If the unfolding input is received from the switch during folding output or the folding input is
received during unfolding output, the existing output stops and new output is activated after
the delay time of about 0.1 second.
When the vehilce speed is above 50 km/h with the mirror unfolded, even though the folding
signal is received it is overridden.
(folding is possible only at vehicle speed of less than 50 km/h ) 1.
2.
3.
4.
5.
6.

02-578710-01
STICS Outside Rearview Mirror Folding/Unfolding Control Circuit ▶
If you remove the ignition switch and open the driver's door with the sunroof open, the chime
buzzer sounds.
As soon as you close the driver's door or the sunrooof, the chime buzzer output stops.
However, when operating conditions in step (1) are met after the operation in step (2), the
chime buzzer will not sound again. If you turn the ignition swtich to the "ON" position again
and the operating contions in step (1) are met, the chime buzzer sounds again.
If the operating condtions for door ajar warning and sunroof open warning are met at the
same time, the sunroof open warning is activated preferentially. 1.
2.
3.
4. In order to prevent the driver from getting off the vehicle with the sunroof open, the reminder
function for the driver is added. This function is activated as follows:Sunroof open warning ▶

02-60
You can register up to 2 transmission codes to the remote control key.
The receiver does not output the received code during registration.
The remote control key should be coded using the diagnostic device. a.
b.
c.
1) Operating requirements
You should remove the ignition key.
2) Code registration requirement
You can register the code only using the diagnostic device.
3) Transmitter code registration
5. REKES Key Coding

02-618710-01
4) How to Code REKES Key
If you replace the REKES key or immobilizer & rechargeable key to new one, you should code the
REKES key using the diagnostic device. (maximum 5)
Connect the diagnostic device to the vehilce and select the vehicle type and system (RK-
STICS). When the following screen is displayed, select 'REMOCON CODING'. 1.
Remove the remote control key from the ignition key box and press 'Next'. Press the door
UNLOCK (PANIC) button on the remote control key once (for approx. 2 seconds or longer). 2.

02-630000-00
5) How to Register Transponder
Insert the ignition key into the key cylinder and turn it to the "ON" position.
Select the vehicle type and system (immobilizer) on the diagnosis program.
Select the Transponder registration menu and enter the password. (initial value is "0000") Select
"Next". 1.
2.
3.
Press "Next" with the first key in key box. 4.

03-4
2) System Diagram
The certification for the immobilizer is performed when turning the ignition switch to the "ON" position
after the CAN communication between the ECU and immobilizer is established.