2012 SSANGYONG KORANDO turn signal

04-18
(4) Remote keyless panic
When the SKM receives the panic signal with the ignition status OFF, ACC ON or IGN ON, the SKM
transmits the REKES panic signal through the BCAN. The SKM transmits the signals for [REKES panic] by the panic button of the smart key to the BCM.
Panic siren mode by REKES panic control ▶ The SKM receives the REKES panic signal 1 sec. after the panic button on the smart key is turned ON
with the ignition status OFF, ACC or IGN ON, and it transmits this signal through the BCAN.Remote keyless panic ▶

04-198712-03
4) Smart Key Verification Time Control
(1) Pre-verification timer
When the operation signal from the START switch is received, the START & power control functions can
be performed without smart key verification.
(2) Immobilizer verification timer
The immobilizer verification status indicates that it is possible to respond to the request message sent
from the EMS to deactivate the immobilizer. The SKM verified a smart key and the engine can be
started.
The 30-second immobilizer verification time is started when:
the ignition status is changed to IGN by the START switch while the pre-verification timer is activated.
the ignition status is changed to IGN by the smart key verification while the pre-verification timer is
stopped; the SKM verified a smart key by the brake switch signal while the immobilizer verification
timer is stopped or the ignition status is IGN ON.
the SKM verified a smart key successfully if the immobilizer verification timer is stopped with IGN
ON/immobilizer verification /brake switch ON. -
-
-
Condition SKM operation
- when door closed signal is input with - B+ or ACC ON
- when brake is applied with - B+ or ACC ON
- when START switch is operated with - B+
- when smart key is inserted into slot & brake switch is
operated or START switch is operated with - B+Once the vehicle interior verification
is completed, 30 sec. pre-verification
timer is started
when the ignition is turned OFF with IGN ON and engine
running 30 sec. pre-verification timer is
started without re-verification
Timer deactivation conditions: after 30 sec. has passed, IGN ON, Outside door handle switch ON,
entering theft deterrent mode when door condition is changed
IGN1 OFF
30 sec. has passed after immobilizer verification
Any door is opened and then closed when all doors are closed & smart key out
When the engine starts to run, the immobilizer verification status is determined, and the immobilizer will
not be deactivated until the ignition status is changed to IGN/ACC/OFF.
The immobilizer is not deactivated when the key out warning condition is met while the engine is
running. (when the RND is received by the EMS reset while the engine is running)
When attempting to start the engine without immobilizer verification, the system performs smart key
verification procedures, and sends the engine start request to EMS only when the verification result is
normal. -
-
-
*
*
*Entry conditions ▶
Deactivation condition ▶

04-22
When the ignition status is changed, the SKM communicates according to the body network
conditions as follows: 9.
OFF → ACC: Keep communicating for 5 sec.
OFF → IGN: Keep communicating
ACC → IGN: Keep communicating
IGN → Cranking: Keep communicating
Cranking→ IGN: Keep communicating
IGN → ACC: Keep communicating for 5 sec.
ACC → OFF: Keep communicating for 5 sec.
IGN → OFF: Keep communicating for 5 sec. -
-
-
-
-
-
-
-
(3) Engine start
When the START button is pressed with the brake pedal applied and gear selector lever in P or N
position, the SKM performs the immobilizer verification and sends the engine START request signal
to the EMS if a normal coded smart key is found.
When the .engine start request signal from the START switch is received, the SKM sends the start
request signal through the PCAN and the smart key location signal through the BCAN to crank the
engine.
The SKM cuts the power for IGN2 and ACC relays while the engine is cranking as cutting the electric
load is necessary.
The SKM receives the engine start status signal from the EMS through the PCAN.
The SKM turns on the ACC/IGN2 relays after the engine cranking and sends the signal for [IGN after
starting] through BCAN.
When the START button is pressed and engine cranking request1 signal is sent, the EMS cranks the
engine after checking the engine warming up. If the engine cranking request2 signal is sent, the EMS
cranks the engine without checking the engine warming up. 1.
2.
3.
4.
5.
6.
Engine cranking request1:
When the START switch is pressed briefly under a normal condition
Engine cranking request2:
When the START switch is pressed once again while the engine cranking request1 signal is sent,
OR When the START switch is pressed for 3 sec. or more -
-
Starting engine while driving 7.
The engine start request signal is sent when the START switch is pressed, provided that the
vehicle speed is less than 10 Km/h or no vehicle speed signal is input, the gear selector lever is in
N position and the brake switch is ON with IGN ON (30 sec. verification is not required).
The engine start request signal is sent regardless of the brake signal when the START switch is
pressed, provided that the vehicle speed is 10 Km/h or more and the gear selector lever is in N
position with IGN ON (30 sec. verification is not required). -
-

04-238712-03
(4) Engine stop
When the START button is pressed at the vehicle speed of 3 km/h or less, the SKM turns off the IGN
relay to stop the engine.
When the vehicle speed is 3 km/h or more or no speed signal is input, the SKM performs the
following functions: 1.
2.
When the START switch is pressed for 3 sec. or more at more than 3 km/h, the ignition status is
changed from IGN to ACC.
If the switch is pressed again, the ignition status is changed from ACC to IGN.
When the START switch is pressed for 3 sec. or more with no vehicle speed signal (CAN signal
timeout, abnormal signal), the ignition status is changed from IGN to ACC. If the switch is pressed
again, the ignition status is changed from ACC to OFF. -
-
When the START button is pressed and held with IGN ON, the ignition status is changed to OFF.
When the START button is pressed briefly, the ignition status is changed to ACC ON. 3.
(5) ACC ON/Power OFF
The SKM changes the ignition status to OFF from ACC ON when:
the engine START/STOP button is pressed with the brake pedal released after the ignition status is
changed from IGN ON to ACC ON.
the REKES LOCK or passive LOCK is operated with ACC ON.
the BCM sends the driver's door open signal.
12 minutes have passed with ACC ON. 1.
2.
3.
4.Except brake switch signal input
For the vehicles with A/T, when the START switch is pressed for 10 sec. or more, the ignition
status is changed to IGN ON and the engine start request signal is sent regardless of the brake
signal, provided that the initial ignition status is ACC ON and the gear selector lever is in P or N
position. *-

05-138010-01
Indicator
(amber)
ESP ▶
ESP OFF indicator ▶
Engine check warning lamp ▶
Indicator
(amber)
Indicator
(amber)
Indicator (red)
Battery charge warning lamp ▶
Indicator (red)
Engine oil level warning lamp ▶This lamp comes on if any sensor or device related to the engine control is
defective.
This lamp comes on when the start switch is ON or when the battery level is
low.
(For EEM, warning lamp is controlled according to CAN signal)
This lamp comes on when the ignition switch is turned to "ON" position,
and then goes off if the engine oil level is normal.
If the engine oil level warning lamp comes on while driving, check the
engine oil level and oil leakage. -
- This indicator comes on when the ESP system is faulty.
This indicator comes on when pressing the ESP OFF switch.

05-16
Indicator
(green)
Passenger seat belt reminder ▶
Left turn signal indicator ▶
Right turn signal indicator ▶
Indicator
(red)
Indicator
(green)
Indicator
(red)
Winter mode indicator(DSL only) ▶The right turn signal indicator blinks if the light switch is pushed up to the right,
and both turn signal indicators blink if the hazard warning flasher switch is
pressed.
When the mode switch is pressed, the winter mode is selected and the
winter mode indicator comes on on the instrument cluster. The winter
mode is used to start off on a slippery road with the 2nd gear. If the switch
is pressed again, the winter mode is deactivated and system returns to
standard mode.This indicator comes on when the ignition switch is turned to the "ON"
position and goes off when the passenger's seat belt is fastened.
The left turn signal indicator blinks if the light switch is pushed down to the
left, and both turn signal indicators blink if the hazard warning flasher switch
is pressed.
Smart key warning lamp ▶
Indicator
(amber)
This lamp comes on when the uncertified transponder or smart key is
detected,
SKM system is defective or there is no smart key in the vehicle.

05-258010-01
Operations for power supply in SVC ▶
When the ignition switch is turned to ON position, the message "WELCOME" is displayed for 2
seconds on the DOT LCD and the seat belt reminder comes on for 4 seconds. However, if a signal
with higher priority is received, the seat belt reminder comes on only for 2 seconds to display it.
The pre-warning (system check) indicator comes on for 4 seconds and goes off 0.4 seconds after
that the ignition is switched on.
All input signals can be input 4 seconds after the pre-warning (system check) indicator starts
illuminating.
Only the symbol and DOT LCD are illuminated initially, if the SKM (Smart Key Module) or door (B-
CAN) signal is received
while B+ power is supplied.
If the ignition is switched on with the LCD illuminated, the DOT LCD and the symbol follow
the side fascia panel.
When the step 1, 2 and 3 are performed after 4 seconds, the seat belt warning lamp is deactivated in
advance.
Dial light ON condition: Lights up gradually for 2 seconds when the ignition is switched on. 1.
2.
3.
4.
5.
6.
5) Illumination & Brightness
(1) Operations for Power Supply

05-318010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch to
ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.