2012 SSANGYONG KORANDO turn signal

05-338010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch
to ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.

05-44
Timeout processing time for buzzer interval after measuring distance/self diagnosis: 600 ms
- If timeout is reached, the PAS returns to undetected condition.
Process while re-inputting
After timeout, the process is performed normally if the signal required for display is received from
beginning to end.
(not detectable if the signal is received in the midst of process) 1.
2.Exception/error handling -Buzzer interval when measuring distance ▶

05-498010-01
Pin No.Message
Operating condition
Domestic Export
Winter mode
(SVC class)
Tire alignment
(applies to
vehicle with
EPS)
CAN scan(This message goes off when all the CAN signal inputs
are normal)
The message "SET WINTER MODE" is displayed
on the LCD display when the winter mode is
activated. The message "RELEASE WINTER
MODE" is displayed when it is deactivated.
The message "WINTER MODE" is displayed when
the vehicle starts off with the winter mode set. -
-
This message helps the driver to predict the driving
direction since the tire alignment is displayed on the
instrument cluster.
The images on the left show that the tires are
aligned to the left. When the tires are aligned to the
right, the image is symmetrical vertically.
Tire alignment is displayed between level 0 and
level 5 depending on the alignment degree when
the ignition switch is turned to "ON" position from
"OFF" position with the shift lever in "P" or "N"
position. While the images up to level 2 comes on
for 5 seconds, the images from level 3 stay on.
These messages are not displayed when the EPS
check message is displayed. -
-
-
-
Pin No. Message Operating condition

05-50
5. SELF DIAGNOSIS
1. Self diagnosis for gauge
Speedometer: Check the whole speed range (minimum to maximum).
Tachometer: Check the whole rpm range (minimum to maximum). -
-
2. Self diagnosis for symbols
All symbols ON
(except the wired type symbols: air bag, passenger air bag, turn signal indicators, hazard warning
lamp, high beam, front fog lamp) -
3. ETC
When entering into the self diagnosis mode, the instrument cluster illumination output will be 100%.
All the remaining segments are ON.
The spanner symbol goes off if CAN messages to the instrument cluster are OK. If not, it blinks.
The mode and illumination switch inputs are overridden. -
-
-
-
6. VARIANT CODING
The instrument cluster enables all functions by receiving the vehicle's variant codes through CAN
communication when turning the ignition switch to ON position.
The systems verified by variant code performs the pre-warning and time-out operation. If not
confirmed, all data for the systems, even exiting in CAN network, are overridden. -
- 4. Diagnosis mode deactivation condition
The diagnosis mode is deactivated when the ignition switch is turned to "OFF" position or the
engine is running. -

06-138510-00
Door lock/unlock control by central door lock switch ▶
When pressing the central door lock/unlock switch, BCM sends the LOCK or UNLOCK signal
according to the previous condition of driver door lock switch for 0.5 seconds.
The central door dock switch is not available when the system is in theft deterrent mode.
When turning the ignition off, all doors are automatically unlocked if any of the door lock (knob)
switches is in LOCK position.
When pressing the central door lock switch with any door open, the system unlocks the doors
immediately after locking them. 1.
2.
3.
4.

06-158510-00
The outside mirror folding switch is self return type and the aiming switch is seesaw and self return type.
Do not fold or unfold the outside rearview mirrors manually. It may cause a malfunction of the mirror
folding system.
Setting 1.
Set auto folding function: When pressing the mirror folding switch for over 3 seconds, the auto folding
function is set and the internal buzzer sounds once (ON: 0.1 sec, OFF: 0.2 sec).
Release auto folding function: When pressing the mirror folding switch for over 3 seconds, the auto
folding function is set and the internal buzzer sounds twice (ON: 0.1 sec, OFF: 0.2 sec). -
-
Auto folding: 2.
When receiving the LOCK signal from the REKES, the system operates in the sequence of "Door lock
<02e70047007b008f008c008d009b0047008b008c009b008c00990099008c0095009b004700940096008b008c00470088008a009b0090009d0088009b009000960095004702e700470074009000990099009600990047008d00960093008b00900095008e00
490047008d0096009900470069006a00740047009e0090009b>hout SKM.
When receiving the outside door handle switch signal or door lock signal from the smart key remote
control, the system o
perates in the seq<009c008c0095008a008c00470096008d0047006b009600960099004700930096008a0092004702e70047007b008f008c008d009b0047008b008c009b008c00990099008c0095009b004700940096008b008c00470088008a009b0090009d0088009b009000
960095004702e70047>
Mirror folding" for BCM with SKM. -
-
Auto unfolding sequence
When receiving the UNLOCK signal from the REKES, the system operates in the sequence of "Door
unlock → Theft deterrent mode deactivation → Mirror unfolding" for BCM without SKM.
When receiving the outside door handle switch signal or door unlock signal from the smart key remote
control, the system operates in the sequence of Door unlock → Theft deterrent mode
deactivation → Mirror unfolding" for BCM with SKM.
When the auto folding function is set, the automatic unfolding is not available if the mirrors have been
folded manually.
(The outside rearview mirror will be folded automatically if the auto folding function is set.)
The factory setting is the enabling the auto folding function. 3.
4.
5.Auto folding/unfolding control ▶

06-16
Operation curve ▶
Folding/unfolding control ▶
When pressing the mirror folding/unfolding switch with IGN ON, the mirrors are folded or unfolded
according to the mirror condition. If the outside rearview mirror was folded, the mirror should be
<009c0095008d00960093008b008c008b0053004700880095008b0047009d0090008a008c0047009d008c0099009a008800550047006d00960093008b00900095008e0056009c0095008d00960093008b00900095008e00470096009c009b0097009c009b00
470090009a00470088008a009b0090009d0088009b008c008b> for 16±6 seconds.
This operation time should be completed even when the ignition switch is turned to OFF position
during its operation.
At first time pressing the mirror folding/unfolding switch after reconnecting the battery, the mirror
folding operation is performed.
You can control the mirror position within the first 30 sec. after turning the ignition OFF. In other
words, this control must be available for 30 seconds (time lag period) after turning the ignition switch
to OFF position. Folding/unfolding is completed when time lag of 30 seconds elapse during
operation.
When receiving the folding/unfolding signal during the mirror folding/unfolding operation, the output
should be activated after having time lag of 0.1 second.
The folding/unfolding operation is performed regardless of the vehicle speed.
Manual operation
<005400470074009000990099009600990047009c0095008d00960093008b008c008b004702e700470074009000990099009600990047008d00960093008b00900095008e0056009c0095008d00960093008b00900095008e0047009a0090008e0095008800
930047008d0099009600940047009a009e0090009b008a008f> → Mirror folding
<005400470074009000990099009600990047008d00960093008b008c008b004702e700470074009000990099009600990047008d00960093008b00900095008e0056009c0095008d00960093008b00900095008e0047009a0090008e009500880093004700
8d0099009600940047009a009e0090009b008a008f004702e7> Mirror unfolding 1.
2.
3.
4.
5.

06-20
Temperature dial
In full AUTO mode, the FATC receives various signals
such as the indoor temperature, ambient temperature,
engine coolant temperature, sunlight, from different
sensors to control the A/C compressor, mode door, intake
actuator assembly, air mix door, blower motors, etc. to
keep indoor environments fresh.
Fan speed dial
In full AUTO mode, the blower
motor is controlled
automatically according to the
set temperature. The blower
motor speed can also be
controlled manually.Mode dial
You can choose a desired
mode from the 5 modes by
turning the mode as required.
The dial indicator for the
selected mode comes on to
inform the operator.
Air source mode switch
When you press this switch,
recirculation indicator comes on and
the system is changed into the
recirculation mode. (However, under
defroster
mode or defroster/floor mode, it stays
in the fresh air mode.)
A/C switch
When pressing this switch, the
air conditioner operates in
manual mode and A/C ON
indicator comes on.
The A/C starts automatically
when the defroster mode is
selected.