2012 RENAULT SCENIC replace battery

13B-170
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF249
PRESENT
OR
STOREDINJECTOR CONTROL
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault becomes present after:
– the ignition is switched on,
– the engine is started.
Priorities when dealing with a number of faults:
– DF046 Battery voltage,
– DF026 Cylinder 1 injector control circuit,
– DF027 Cylinder 2 injector control circuit,
– DF028 Cylinder 3 injector control circuit,
– DF029 Cylinder 4 injector control circuit.
Special notes:
If the fault is present:
– in certain cases, the level 2 warning light is lit and the engine is stopped.
Use bornier Elé.1681 for all operations on the engine management computer.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
This fault appears when the computer detects a fault on the injector control section.
Check the condition of the injector connectors (see Wiring Diagram Technical Note, Laguna II ph2, Vel Satis
ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component codes 193, 194, 195, 196).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
EDC16CP33_V18_DF249 / EDC16CP33_V1C_DF249 / EDC16CP33_V54_DF249 / EDC16CP33_V20_DF249 / EDC16CP33_V58_DF249 /
EDC16CP33_V5C_DF249 / EDC16CP33_V24_DF249 / EDC16CP33_V04_DF249 / EDC16CP33_V08_DF249 / EDC16CP33_V44_DF249 /
EDC16CP33_V4C_DF249 / EDC16CP33_V34_DF249 / EDC16CP33_V38_DF249 / EDC16CP33_V74_DF249 / EDC16CP33_V28_DF249 /
EDC16CP33_V62_DF249 / EDC16CP33_V26_DF249 / EDC16CP33_V60_DF249
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-212
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF364
PRESENT
OR
STOREDHEATING AND AIR CONDITIONING SYSTEM
CC.0: Short circuit to earth
CO.1: Open circuit or short circuit to +12 V
CC.0
CO.1
NOTESSpecial notes:
Use bornier Elé. 1681 for all operations on the engine
management computer connectors.
Use the Wiring Diagram Technical Note for Mégane II
ph2 or Scénic II ph2.
Check the heating and air conditioning circuit (see MR 364 (Mégane II ph2), 370 (Scénic II ph2) Mechanical,
62A, Air conditioning).
Check the condition of the refrigerant pressure sensor connector (see Wiring Diagram Technical Note,
Mégane II ph2 or Scénic II ph2, component code 1202).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2 or Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Disconnect the battery and the injection computer.
Check the insulation and continuity of the following connections:
•38Y between components 120 and 1202,
•38X between components 120 and 1202,
•38U between components 120 and 1202.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
EDC16CP33_V18_DF364 / EDC16CP33_V1C_DF364 / EDC16CP33_V54_DF364 / EDC16CP33_V20_DF364 / EDC16CP33_V58_DF364 /
EDC16CP33_V5C_DF364 / EDC16CP33_V24_DF364 / EDC16CP33_V04_DF364 / EDC16CP33_V08_DF364 / EDC16CP33_V44_DF364 /
EDC16CP33_V4C_DF364 / EDC16CP33_V34_DF364 / EDC16CP33_V38_DF364 / EDC16CP33_V74_DF364 / EDC16CP33_V28_DF364 /
EDC16CP33_V62_DF364 / EDC16CP33_V26_DF364 / EDC16CP33_V60_DF364
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-216
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF532
PRESENT
OR
STOREDALTERNATOR CHARGE SIGNAL
1.DEF: Internal electronic fault
2.DEF: Inconsistent signal
NOTESPriorities when dealing with a number of faults:
– DF046 Battery voltage.
Conditions for applying the fault finding procedure to a stored fault:
If the fault is declared present after:
– starting the engine,
– a road test.
Special notes:
Computer operating voltage: 6 V < operating voltage < 16.5 V.
Use bornier Elé.1681 for any operations on the injection computer connectors.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
Check the condition of the alternator connector (see Wiring Diagram Technical Note, Laguna II ph2, Vel Satis
ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 103).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
EDC16CP33_V18_DF532 / EDC16CP33_V1C_DF532 / EDC16CP33_V54_DF532 / EDC16CP33_V20_DF532 / EDC16CP33_V58_DF532 /
EDC16CP33_V5C_DF532 / EDC16CP33_V24_DF532 / EDC16CP33_V28_DF532 / EDC16CP33_V62_DF532 / EDC16CP33_V26_DF532 /
EDC16CP33_V60_DF532
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-221
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF645
PRESENT
OR
STOREDDAMPER VALVE POSITION REGULATION
1.DEF: Data inconsistency
2.DEF: Value outside permitted tolerance values
3.DEF: Damper valve jammed open
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– with the engine running,
– the battery voltage X > 8V.
Priorities when dealing with a number of faults:
– DF038 Computer,
– DF323 Damper valve,
– DF012 Sensor supply voltage no. 2,
– DF646 Damper valve position sensor.
Special notes:
If the fault is present:
–the level 1 warning light is lit (for Vdiag 20, 58, 24, 5C, 26, 28, 60 and 62),
– particle filter regeneration is inhibited.
Use bornier Elé. 1681 for all operations on the engine management computer
connector.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
Check the condition and connection of the damper valve connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1461).
Check the condition and connection of the engine management computer connector (see Wiring Diagram
Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code
120).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
EDC16CP33_V18_DF645 / EDC16CP33_V1C_DF645 / EDC16CP33_V54_DF645 / EDC16CP33_V20_DF645 / EDC16CP33_V58_DF645 /
EDC16CP33_V5C_DF645 / EDC16CP33_V24_DF645 / EDC16CP33_V04_DF645 / EDC16CP33_V08_DF645 / EDC16CP33_V44_DF645 /
EDC16CP33_V4C_DF645 / EDC16CP33_V34_DF645 / EDC16CP33_V38_DF645 / EDC16CP33_V74_DF645 / EDC16CP33_V28_DF645 /
EDC16CP33_V62_DF645 / EDC16CP33_V26_DF645 / EDC16CP33_V60_DF645
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-268V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET007
CONTINUED
"ACTIVE"
– Check the connection and condition of the preheating unit (see Wiring Diagram
Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2,
Scénic II ph2, component code 257).
If the connector or connectors are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
If the vehicle starts, postheating has ended and status ET007 remains ACTIVE
during the engine operating phase, refer to the interpretation of faults DF017
Preheating unit control circuit and DF025 Preheating unit diagnostic
connection.
"INACTIVE"If the vehicle does not start, the status remains INACTIVE and preheating does not
start when the ignition is switched on or during the starting phase.
Check the continuity and absence of interference resistance on the following
connections:
•3FY and 3FF between components 120 and 257.
Check the + 12 V battery supply to the preheating unit on the following connection:
•BP35 of component 257.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Conformity check with the engine running and engine coolant temperature > 80°C
"ACTIVE"
then
"INACTIVE"After the engine has been running for a certain period, the status changes from
ACTIVE to INACTIVE.
In the event of a fault, consult the interpretation of fault DF017 Preheating unit
control circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-442V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC031THERMOPLUNGER No. 3 RELAY
NOTESCheck that the computer is correctly configured using command LC056
Thermoplungers
There must be no present or stored faults:
Perform this fault finding procedure if there is a fault with the passenger compartment
heating - demisting.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
If the Thermoplunger no. 3 relay or the additional heater interface unit does not function when command
AC031 is run.
Check the condition of the thermoplunger 3 relay mounting on the engine fuse box or the additional heater
interface unit (see Wiring Diagram Technical Note, Vehicle, component code 1069 or 1550).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Vehicle, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
if the fault is still present, check as follows that this relay is controlled by the engine management computer:
Disconnect the thermoplunger no. 3 relay and fit a 50 Ω to 100Ω resistor on its mounting instead of the coil and
connect a voltmeter as follows:
– positive terminal to + 12 V battery,
– negative terminal to connection 3JAB of component 1069 or 1550.
Run command AC031.
If the voltmeter indicates the battery voltage (4 ON-OFF cycles of 10 seconds), replace the thermoplunger no. 3
relay.
If the voltmeter does not show the battery voltage (4 ON-OFF cycles of 10 seconds), contact the Techline.
EDC16CP33_V18_AC031 / EDC16CP33_V1C_AC031 / EDC16CP33_V54_AC031 / EDC16CP33_V20_AC031 / EDC16CP33_V58_AC031 /
EDC16CP33_V5C_AC031 / EDC16CP33_V24_AC031 / EDC16CP33_V04_AC031 / EDC16CP33_V08_AC031 / EDC16CP33_V44_AC031 /
EDC16CP33_V4C_AC031 / EDC16CP33_V34_AC031 / EDC16CP33_V38_AC031 / EDC16CP33_V74_AC031 / EDC16CP33_V28_AC031 /
EDC16CP33_V62_AC031 / EDC16CP33_V26_AC031 / EDC16CP33_V60_AC031
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-444V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC037PREHEATING RELAY
NOTESThis command is only run if fault DF025 Preheating unit diagnostic connection or
DF017 Preheating unit control circuit is present or stored and if no other fault is
present.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
IMPORTANT:
– Please observe the cleanliness guidelines and safety advice.
– Make sure the correct type of plug is fitted on the vehicle, slow or fast:
Slow plugs have a black ring
Quick plugs have a white ring.
For Vdiag 20, 24, 34, 38 and 74, if replacing heater plugs by plugs of a different type
(see Replacement of components and Replacing heater plugs).
Before applying the following fault finding procedure, check that the battery voltage is not below 12 V. Otherwise,
recharge the battery.
STEP 1:
Using a multimeter fitted with a current clamp, bring together the 4 heater plug supply wires.
Run command AC037 and measure the current consumed by the 4 heater plugs.
If the value of the current consumed is not between 60 A and 80 A, move on to step 2, otherwise end of fault
finding.
EDC16CP33_V18_AC037 / EDC16CP33_V1C_AC037 / EDC16CP33_V54_AC037 / EDC16CP33_V20_AC037 / EDC16CP33_V58_AC037 /
EDC16CP33_V5C_AC037 / EDC16CP33_V24_AC037 / EDC16CP33_V04_AC037 / EDC16CP33_V08_AC037 / EDC16CP33_V44_AC037 /
EDC16CP33_V4C_AC037 / EDC16CP33_V34_AC037 / EDC16CP33_V38_AC037 / EDC16CP33_V74_AC037 / EDC16CP33_V28_AC037 /
EDC16CP33_V62_AC037 / EDC16CP33_V26_AC037 / EDC16CP33_V60_AC037
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-445V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC037
CONTINUED
STEP 2:
Check the connections of the preheating unit, component code 257, the heater plugs, component codes 680, 681,
682 and 683 and the injection computer, component code 120.
Measure the resistance of the heater plugs. If the resistance value is > 2 Ω, replace the faulty plug or plugs,
making sure that the correct plug type, slow or fast, is fitted on the vehicle.
Check the continuity and absence of interference resistance of the following connections:
•37AB between components 257 and 683,
•37AA between components 257 and 680,
•37Z between components 257 and 681,
•37AC between components 257 and 682.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition of the preheating unit supply fuse (70 A) (see MR 364 (Mégane II ph2), MR 370 (Scénic II
ph2), MR 395 (Laguna II ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2) Mechanical, 81C, Fuses, Fuses: List
and location of components).
Check the + 12 V battery supply to the preheating unit on the following connection:
•BP35 of component 257.
Check the continuity and absence of interference resistance of the following connections:
•3FY between components120 and 257,
•3FF between components120 and 257.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the preheating unit.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.