2012 RENAULT PULSE heater


> (GLW    0RGHO .$2(0B5HQDXOW @
JVH0005XType B1. SOURCE select s\fitch
2. V\blume c\bntr\bl s\fitch
3. Tuning s\fitch
The audi\b system can be \bperated using the c\bntr\bls
\bn the steering \fheel.
SOURCE select s\fitch
Push the SOURCE select s\fitch t\b change the m\bde
t\b available audi\b s\burce.
V\blume c\bntr\bl s\fitch
Push up \br d\b\fn the v\blume c\bntr\bl s\fitch t\b increase
\br decrease the v\blume.
Tuning s\fitch
Memory change (radio):
Push the tuning s\fitch f\br less than 1.5 sec\bnds t\b
change the next \br previ\bus radi\b preset.
SEEK tuning (radio):
Push the tuning s\fitch f\br m\bre than 1.5 sec\bnds t\b
seek the next \br previ\bus radi\b stati\bn. APS (Automatic Program Search) FF, APS REW
(CD):
Push the tuning s\fitch f\br less than 1.5 sec\bnds t\b
return t\b the beginning \bf the present pr\bgram \br skip
t\b the next pr\bgram. Push several times t\b skip back \br
skip thr\bugh pr\bgrams.
This system searches f\br the blank intervals bet\feen
selecti\bns. If there is a blank interval \fithin \bne
pr\bgram \br there is n\b interval bet\feen pr\bgrams,
the system may n\bt st\bp in the desired \br expected
l\bcati\bn.
Type A:
JVH0007X
The USB/AUX c\bnnect\br is \bn the l\b\fer center \bf the
instrument panel.
F\br details, see the separately pr\bvided Navigati\bn
O\fner’s Manual.
Type B:
JVH0731X
The USB/AUX c\bnnect\br is l\bcated \bn the instrument
panel. F\br details, see “USB mem\bry device \bperati\bn”
(P.4-50) , “iP\bd player \bperati\bn” (P.4-50) \br “Audi\b
main \bperati\bn” (P.4-47) .
Heater and air conditioner, and audio system4-55
USB/AUX CONNECTOR (if
equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-56Heater and air conditioner, and audio system
When installing a CB, ham ra\fio or a car phone in \bour
vehicle, be sure to observe the following cautions,
otherwise the new equipment ma\b a\fversel\b affect the
Engine Control S\bstem an\f other electronic parts.
CAUTION:
.Keep the antenna as far away as possible
from the Electronic Control Module.
. Keep the antenna wire at least 20 cm (8 in)
away from the Engine Control harnesses. Do
not route the antenna wire next to any
harnesses.
. Adjust the antenna standing wave ratio as
recommended by the manufacturer.
. Connect the ground wire from the radio
chassis to the body.
. For details, consult a RENAULT dealer.
WARNING:
.Use a phone after stopping your vehicle in a
safe location. If you have to use a phone
while driving, exercise extreme caution at all
times so full attention may be given to
vehicle operation.
. If a conversation in a moving vehicle re-
quires you to take notes, pull off the road to
a safe location and stop your vehicle before
doing so.
CAUTION:
To avoid draining the vehicle battery, use a
phone after starting the engine.
For mo\fel with navigation s\bstem, see the separatel\b
provi\fe\f Navigation Owner’s Manual.
Your vehicle is equippe\f with the Bluetooth
ŠHan\fs-
Free Phone S\bstem. If \bou are an owner of a
Bluetooth
Šenable\f cellular phone, \bou can set up
the wireless connection between \bour cellular phone
an\f the in-vehicle phone mo\fule. With Bluetooth
Š
wireless technolog\b, \bou can make or receive a han\fs-
free telephone call with \bour cellular phone in the
vehicle.
Once \bour cellular phone is paire\f to the in-vehicle
phone mo\fule, no other phone connecting proce\fure
is require\f. Your phone is automaticall\b connecte\f with
the in-vehicle phone mo\fule when the ignition switch
is place\f in the “ON” position with the paire\f cellular
phone turne\f on an\f carrie\f in the vehicle.
You can register up to 5 \fifferent Bluetooth
Šcellular
phones to the in-vehicle phone mo\fule. However, \bou
can talk on onl\b one cellular phone at a time.
Before using the Bluetooth
ŠHan\fs-Free Phone S\bstem, refer to the following notes.
.
Set up the wireless connection between a cellular
phone an\f the in-vehicle phone mo\fule before
using the s\bstem.
. Some Bluetooth
Šenable\f cellular phones ma\b not
be recognize\f b\b the in-vehicle phone mo\fule.
. You will not be able to use a han\fs-free phone
un\fer the following con\fitions.
— Your vehicle is outsi\fe of the telephone service
area.
— Your vehicle is in an area where it is \fifficult to receive ra\fio waves; such as in a tunnel, in an
un\fergroun\f parking garage, near a tall buil\f-
ing or in a mountainous area.
— Your cellular phone is locke\f to prevent it from being \fiale\f.
When the ra\fio wave con\fition is not i\feal or ambient
soun\f is too lou\f, it ma\b be \fifficult for the other part\b
to hear \bour voice \furing a call. Please close the
win\fows if possible.
Do not place the cellular phone in an area surroun\fe\f
b\b metal or far awa\b from the in-vehicle phone mo\fule
to prevent tone qualit\b \fegra\fation an\f wireless
connection \fisruption.
While a cellular phone is connecte\f through the
Bluetooth
Šwireless connection, the batter\b power of
the cellular phone ma\b \fischarge quicker than usual.
The Bluetooth
ŠHan\fs-Free Phone S\bstem cannot
charge cellular phones.
Refer to the cellular phone Owner’s Manual regar\fing
the telephone charges, cellular phone antenna an\f
bo\f\b, etc.
This wireless han\fs-free s\bstem is base\f on Blue-
tooth
Štechnolog\b.
CAR PHONE OR CB RADIO Bluetooth
ŠHANDS-FREE PHONE
SYSTEM (if equipped for model
without navigation system)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
.Frequency: 2402 MHz - 2480 MHz
. Out\fut Power: 4\b14 dBm EIRP
. Modulation: FHSS GFSK 8DPSK, \f/4DQPSK
. Number of Channel: 79
. This wireless equi\fment cannot be used for any
services related to safety due to the \fossibility of
radio interference
REGULATORY INFORMATION
BluetoothŠis a trademark owned
by Bluetooth SIG, Inc\b and li-
censed to Clarion Co\b, Ltd\b and
Daewoo IS Cor\f\b
CE STATEMENT
Hereby “Yangfeng Visteon Automotive Electronics Co\b,
Ltd\b” and “Clarion Cor\foration” declares that this
Bluetooth car kit AV System is in com\fliance with the
essential requirements and other relevant \frovisions of
Directive 1999/5/EC\b
HANDS-FREE TELEPHONE OPERATION
(Ty\fe A)
JVH0006XFor Europe
JVH0046XFor South Africa1\b PHONE SEND button
2\b PHONE END/BACK button
3\b PHONE BOOK button
The following o\ftions can be selected:
. Paired list
. Pair \fhone
. Delete \fhone
. Bluetooth
Šconnection .
Delete \fhone book
. My number
Pairing \frocedure
If you wish to make a BluetoothŠconnection for the
first time between your mobile \fhone and the Blue-
tooth
Šsystem of the audio unit, \ferform the following
\fairing \frocedure\b
1\b Place the ignition switch in the “ACC” \fosition\b
2\b Switch on the audio system and your mobile \fhone\b
For the vehicle:
1\b Briefly \fush the MENU button\b
2\b Push the ENTER button\b
3\b Turn the MENU/VOL dial and select PAIR PHONE then \fush the ENTER button\b
4\b The dis\flay shows READY TO PAIR then PASS- CODE=1234\b
On the mobile \fhone:
1\b Activate the Bluetooth
Šconnection\b
2\b Activate the search mode for BluetoothŠequi\f-
ment\b Refer to the owner’s manual of your mobile
\fhone for further details\b If the search mode finds
the device, it will be shown on your mobile \fhone
dis\flay\b
3\b Select the device name MY CAR\b
4\b Enter the \fasscode number 1234 as shown on the dis\flay of the audio unit with the key\fad on
your mobile \fhone and then \fush the confirmation
button on your mobile \fhone\b
Heater and air conditioner, and audio system4-57
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-58Heater and air conditioner, and audio system
ActionScreen display
\fush brie\bly MENU button ; \fHONE SETU\f
\fush ENTER ;
Turn VOLUME dial \fAIR \fHONE ;
\fush ENTER READY TO \fAIR
\fASSCODE=1234
;
Your mobile phone setup:
select MY CAR then enter 1234
;
I\b success\bul \fAIRING OK
; CONNECT OK
Mobile 1 *1
\fAIR \fHONE
\fush
\bor the main
screen.
*1: Mobile name
Once the connection is \binalized, the audio unit will
automatically register the mobile phone and the audio
unit display shows \fAIRING OK and CONNECT OK. I\b
it \bails to register, the display shows \fAIRING FAIL
then start the procedure, previously described, again
or consult the owner’s manual o\b your mobile phone.
You can register up to 5 di\b\berent Bluetooth
Šmobile
phones. However, you can only use one mobile phone
at a time. I\b you have 5 di\b\berent Bluetooth
Šmobile
phones registered, a new mobile phone can only
replace one o\b the 5 existing paired phones. Use DEL
\fHONE to delete one o\b the existing paired phones.
\faired phone list
The paired phone list shows which phones have been
paired or registered with the BluetoothŠsystem. I\b the
list contains multiple phones then you can select the
appropriate phone to connect with the Bluetooth
Š
system.
Action Screen display
Brie\bly push MENU
; \fHONE SETU\f
\fush ENTER ; \fAIRED LIST
\fush ENTER ; Mobile 1
Turn MENU/ VOL dial Mobile 2
;
\fush ENTER \fLEASE WAIT
; CONNECT OK
CONNECT
FAIL
\fAIRED LIST
\fush
\bor
the main screen.
In the above example procedure, “Mobile 2” will be
connected.
Removing a paired phone
Deletes the connection between the BluetoothŠ
system and the registered mobile phone. Action Screen display
Brie\bly push MENU
; \fHONE SETU\f
\fush ENTER
;
Turn MENU/VOL dial
; DEL \fHONE
\fush ENTER
; Mobile 1
Turn MENU/VOL dial Mobile 2
;
\fush ENTER DELETE?
;
\fush ENTER * DELETED
; DEL \fHONE
\fush
\bor the main
screen.
*: For the “Mobile 2” connection the screen displays “DISCONNECTED”, \bollowed by “Mo-
bile 2”, then “DELETED”.
In the above example, “Mobile 2” will be deleted while
“Mobile 1” remains connected to the system.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
BluetoothŠactivation
Activates or deactivates the BluetoothŠfunction. You
\fill need to activate the BluetoothŠfunction in order to
enable your hands-free \bhone system (exce\bt in the
\bairing mode \fhen it \fill be activated automatically) .
Action Screen dis\blay
Push MENU ; PHONE SETUP
Push ENTER ;
Turn MENU/VOL dial BLUETOOTH ;
Push ENTER B’TOOTH ;
Turn MENU/VOL dial B’TOOTH ;
Push ENTER BLUETOOTH
Push
for the main
screen.
Dis\blaying MY NUMBER
If your mobile \bhone is equi\b\bed \fith the function, the
\bhone number of the active mobile \bhone \fill be
dis\blayed on the hands-free \bhone system.
Delete \bhone book list
To delete all the contacts from the \bhone book, \broceed as follo\fs:
Action Screen dis\blay
Briefly \bush MENU ; PHONE SETUP
Push ENTER
;
Turn MENU/VOL dial DEL P.BOOK
;
Push ENTER DEL ALL?
;
Turn MENU/VOL dial DEL ALL?
;
Push ENTER DELETING
DELETED
DEL P.BOOK
Push
for the main
screen.
Phone book
When the \bhone bookbutton is \bushed, the
follo\fing o\btions can be selected by turning the
MENU/VOL dial in either direction.
. SEARCH
. Names (contact names)
. S\beed dial mode [1Name (contact name)]
. DELETE NAME
. EDIT NAME
. ADD NAME
. Send name using Bluetooth
Štechnology [ADD NAME] .
Send all the \bhone book entries in the mobile
\bhone using Bluetooth
Štechnology [DOWNLOAD]
The \bhone book can store u\b to 250 names \fith
numbers and can be selected for calling. To add a
contact to the \bhone book \broceed as follo\fs:
Action Screen dis\blay
Push \fith a long \bush
button
; ADD NAME
Push ENTER
; ENTER NAME
Turn MENU/VOL dial ABC
;
Focus on “J” IJK
Push ENTER ;
Turn MENU/VOL dial Focus on “O” NOP
;
Push ENTER ;*1 *3 JO
Turn MENU/VOL dial OK
;
Push ENTER ; ENTER NUMBER
Push ENTER then turn MENU/ VOL dial 1
; *2 *3
Push ENTER 123456789
;
Turn MENU/VOL dial
Heater and air conditioner, and audio system4-59
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-60Heater and air conditioner, and audio system
;OK
Push ENTER SAVED
NOTE:
In the above example the contact name JO and
phone number 123456789 will be added. *\f: To i\bsert special characters select the followi\bg character optio\bs A: Alphabetic characters, \f/2:
Numerical characters, A ¨
: Lati\b characters a\bd
@: Symbol characters.
*2: Select the \bumber the\b co\bfirm your selectio\b by pushi\bg the ENTER butto\b, a\bd the\b proceed
likewise for every \bumber.
*3: To correct a\b e\btry, briefly push the
butto\b
the\b e\bter the correct details. To delete all
characters push the
butto\b for more tha\b \f
seco\bd.
NOTE:
You can also store the name and the phone
number in one of the six preset buttons on the
audio unit for frequently used phone numbers.
Transferring an entry to the phone book:
You ca\b also se\bd a \bame (co\btact) from a co\b\bected
mobile pho\be to the pho\be book usi\bg Bluetooth
Š
tech\bology. Actio\b
Scree\b display
Briefly push
butto\b
;
Tur\b MENU/VOL dial
ADD NAME
;
Push ENTER SEND NAME
; *\f *2 JOE
Push ENTER ;*3 0\f23456789
Push ENTER SAVED YES
;
Push ENTER SAVED
;
ADD NAME
Push
for the mai\b scree\b.
*\f: The Bluetooth
Šico\b will bli\bk for 2 mi\butes.
*2: Se\bd the \bame via the registered mobile pho\be withi\b the 2 mi\butes.
*3: Pho\be \bumber is displayed.
Transferring all phone book entries at the same
time:
If your mobile pho\be is equipped with the fu\bctio\b, you
ca\b dow\bload all the pho\be book e\btries i\b the mobile
pho\be to the ha\bds-free system at the same time. Actio\b
Scree\b display
Briefly push
butto\b
;
Tur\b MENU/VOL dial
DOWNLOAD
;
Push ENTER ; APPEND?
Tur\b MENU/VOL dial OVERWRITE? ;
Push ENTER DOWNLOAD-
ING...
DOWNLOAD OK
DOWNLOAD
Push
for the me\bu
scree\b.
NOTE:
. If you select APPEND, downloaded entries
will be saved in the available space without
deleting previously saved information in the
hands-free system. If there is not enough
space, the downloaded entries that exceed
the space available will not be saved and
MEMORY FULL appears on the display.
. If you select OVERWRITE , the downloaded
entries will be saved on top of the previously
saved information. (The previously saved
information will not be saved.) You can save
up to 250 entries. If you attempt to download
more than 250 entries, the remaining entries
will not be saved and MEMORY FULL
appears on the display.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Edit
You can edit a name or phone number stored in the
phone book.\fction Screen display
\bush
button
;
Turn MENU/VOL dial
; EDIT N\fME
\bush ENTER
;*1
Turn MENU/VOL dial JOE
;
\bush ENTER
; JOE OK <@OK\f>
Turn MENU/VOL dial
;Focus on “Y” JOE
\bush ENTER
;*2*3 JOEY
\bush
for more than
1.5 seconds to go to main screen.
*1: \flternatively use the SE\fRCH mode to select the appropriate entry to edit.
— SE\fRCH appears on the display then push the ENTER button.
— Select the first character of the name then push the ENTER button.
— The name should be displayed. If necessary, turn the MENU/VOL dial to select the correct name.
*2: When the
button is pushed briefly, the
cursor will move one step backwards and the last character will be deleted. To delete all
characters push the
button for more than 1
second.
*3: If necessary, you can edit the telephone number. \ffter editing the name, select OK then push the
ENTER button to confirm and edit the number as
described for name editing.
Delete a name:
To delete a name (contact) from the phone book,
proceed as follows:
1. Briefly push the
button.
2. Turn the MENU/VOL dial then select the DELETE N\fME.
3. \bush the ENTER button.
4. Turn the MENU/VOL dial to the name that needs to be deleted then push the ENTER button.
5. The display will show DELETE? YES. If applicable, turn the MENU/VOL dial to select DELETE? NO.
6. The display will show the message DELETED.
The search mode can also be performed as follows:
1. Briefly push the
button.
2. SE\fRCH appears on the display then push the ENTER button.
3. Select the first character of the name then push the ENTER button.
4. The display will now show the name(s) beginning with the corresponding character. If necessary,
turn the MENU/VOL dial to select the correct
name.
5. \bush the ENTER button and the display will show DELETE? YES. If applicable, turn the MENU/VOL
dial to select DELETE? NO. 6. To confirm the selection, push the ENTER button.
Speed dial buttons:
\ffter entering the names and phone numbers, you can
assign the six preset buttons to the most frequently
dialled phone numbers.
1. \bush the
button.
2. Select the name by turning the MENU/VOL dial or using the search name mode.
3. Once found, push the assigned preset button until a confirmation beep is heard. The name and phone
number are now stored under that button.
Hands-free telephone control
The hands-free mode can be operated using the
telephone button controls on the audio unit or on the
steering wheel.
Initiating a call:
\f call can be initiated using one of the following
methods:
.redial
. phone book
. voice tag
. speed dial (preset buttons)
NOTE:
During the active call you can adjust the micro-
phone volume by briefly pushing the MENU
button then adjusting the volume by turning
the MENU/VOL dial within the value range of í2
to +2. To confirm the entry, briefly push the
ENTER or
button or wait for 10 seconds to
return to the active call main screen.
Heater and air conditioner, and audio system4-61
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-62Heater and air conditioner, and audio system
Redial:
Use the redial mode to call the last num\fer that was
dialled.
1. \briefly push the
\futton.
2. Select REDIAL.
3. Push the ENTER or the
\futton to redial the
last num\fer.
Make a call from the phone book:
In order to dial a contact from the phone \fook, proceed
as follows:
1. Push the
\futton.
2. Turn the MENU/VOL dial and select the corre- spondent name.
3. Push the ENTER or the
\futton in order to dial
the num\fer.
Alternatively, you can use the search mode as follows:
1. \briefly push the
\futton.
2. SEARCH appears on the display then push the ENTER \futton.
3. Select the first character of the name then the ENTER \futton.
4. The name should \fe displayed. If necessary, turn the MENU/VOL dial to select the
correct name.
5. Push the ENTER or
\futton in order to dial the
num\fer.
Calling via voice tag:
If your mo\file phone supports voice recognition, it is
possi\fle to make a call via the voice tag instead of
manual selection, provided the name and num\fer of
your contact has \feen previously marked and stored in
the phone \fook of your mo\file phone. For details, see the mo\file phone manufacturer’s owner’s manual.
In order to dial via a voice tag, proceed as follows:
1. Push the
\futton for more than 2 seconds.
2. The display shows SPEAK NOW.
3. Give your voice tag. Say the voice tag clearly and normally in the
direction of the microphone (located near the map
light) .
4. If the voice tag is correct, the phone system will dial the corresponding num\fer.
Make a call via speed dial:
To make a speed dial call using one of the assigned
preset \futtons, proceed as follows:
1. \briefly push the
\futton.
2. Push the corresponding preset \futton (1-6) . Alternatively, you can select the corresponding
preset num\fer \fy turning the MENU/VOL dial
instead of pushing the preset \futton.
3. To confirm the selection, push the
\futton to
make the call.
Receiving a call
When receiving an incoming call, the display will show
the caller identification (or NO NUM\bER) and you can:
. answer the call \fy \friefly pushing the
\futton.
. end the call after the conversation \fy pushing the
\futton.
. reject the call \fy pushing the
\futton.
Steering wheel switch for \bluetoothŠ
SAA2594
The hands-free mode can \fe operated using the
controls on the steering wheel.
Volume control switch:
The volume control switch allows you to adjust the
volume of the speakers \fy pushing the + or í\futtons
*1.
Telephone button:
The
\futton*2allow you to:
. accept an incoming call \fy pushing the
\futton.
. reject an incoming call \fy pushing the
\futton
during the incoming call.
. end an active call \fy pushing the
\futton
once.
. redial the last outgoing call \fy pushing the
\futton twice.
. make a speed dial call \fy pushing the
\futton then push the scrolling (up/down) switch to
scroll through the preset \futtons for the stored
phone num\fers. To confirm the selection push the
\futton to make the call.
&RQGLWLRQ