2012 RENAULT PULSE reset


> (GLW    0RGHO .$2(0B5HQDXOW @
4. Push the clock adjusting knob*1to adjust the
\finutes.
To advance the ti\fe, hold do\bn the knob
*1.
Wait at least 5 seconds for the second display “:”
to flash.
5. Push the clock adjusting knob
*1to reset the
second counter.
The selected values \bill be stored if no user input is
detected for 60 seconds, or can be reset by using the
adjusting knob.
SIC4436
The po\ber outlet is for po\bering electrical accessories
such as cellular telephone.
CAUTION:
. The outlet and plug may be hot during or
immediately after use.
. This power outlet is not designed for use
with a cigarette lighter unit.
. Do not use with accessories that exceed a 12
volt, 120W (10A) power draw. Do not use
double adapters or more than one electrical
accessory.
. Use power outlets with the engine running
to avoid discharging the vehicle battery.
. Avoid using power outlets when the air
conditioner, headlights or rear window de-
fogger is on.
. Before inserting or disconnecting a plug, be
sure to turn off the power switch of electrical
accessory being used and the ignition
switch.
. Push the plug in as far as it will go. If good
contact is not made, the plug may overheat
or the internal temperature fuse may open. .
Do not allow water to contact the outlet.
. When not in use, be sure to close the cap.
Instruments and controls2-39
POWER OUTLETS (if equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
3-18Pre-driving checks and adjustments
WARNING:
.The hood must be closed and latched
securely before driving. Failure to do so
could cause the hood to fly open and result
in an accident.
. Never open the hood if steam or smoke is
coming from the engine compartment to
avoid injury.
OPENING HOOD
JVP0090X
1. Pu\f\f the h\b\bd \f\bck re\fease hand\fe*1\f\bcated
be\f\bw the instrument pane\f unti\f the h\b\bd springs
up.
2. L\bcate the \fever
*2in between the h\b\bd and
gri\f\fe and push the \fever sideways with y\bur
fingertips.
3. Raise the h\b\bd
*3.
4. Rem\bve the supp\brt r\bd
*4and insert it int\b the
s\f\bt*5.
Hold the coated parts
*Awhen removing or
resetting the support rod. Avoid direct contact
with the metal parts, as they may be hot
immediately after the engine has been stopped.
CLOSING HOOD
1. Whi\fe supp\brting the h\b\bd, return the supp\brt r\bd t\b its \brigina\f p\bsiti\bn.
2. S\f\bw\fy \f\bwer the h\b\bd t\b ab\but 20 t\b 30 cm (8 t\b 12 in) ab\bve the h\b\bd \f\bck, then \fet it dr\bp.
3. Make sure it is secure\fy \fatched.
CAUTION:
Before closing the hood, be sure to release the
support rod and store it in position. Otherwise,
the support rod will be damaged.
HOOD
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
.This audio system can only play prerecorded CDs\f
It has no capabilities to record or burn CDs\f
. If the CD cannot be played\b one of the following
messages will be displayed\f
Check disc:
— Confirm that the CD is inserted correctly (the
label side is facing up\b etc\f) \f
— Confirm that the CD is not bent or warped and it is free of scratches\f
Push eject:
This is a malfunction due to the temperature inside
the player is too high\f Remove the CD by pushing
the EJECT button\b and after a short time reinsert
the CD\f The CD can be played when the
temperature of the player returns to normal\f
Unplayable:
The file is unplayable in this audio system (only
MP3 or WMA CD) \f
USB (Universal Serial Bus) (if equipped)
WARNING:
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious injury.
CAUTION:
. Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side-down into the port may damage the
port. Make sure that the USB device is
connected correctly into the USB port.
. Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port. This could damage the port and the cover.
. Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
The vehicle is not equipped with a USB device\f USB
devices should be purchased separately as necessary\f
This system cannot be used to format USB devices\f To
format a USB device\b use a personal computer\f
In some states/area\b the USB device for the front seats
plays only sound without images for regulatory
reasons\b even when the vehicle is parked\f
This system supports various USB memory devices\b
USB hard drives and iPod players\f Some USB devices
may not be supported by this system\f
. Partitioned USB devices may not be played
correctly\f
. Some characters used in other languages (Chi-
nese\b Japanese\b etc\f) are not displayed properly
on display\f Using English language characters
with a USB device is recommended\f
General notes for USB use:
Refer to your device manufacturer’s owner information
regarding the proper use and care of the device\f
Notes for iPod use:
iPod is a trademark of Apple Inc\f\b registered in the U\fS\f
and other countries\f
. Improperly plugging in the iPod may cause a
checkmark to be displayed on and off (flickering) \f
Always make sure that the iPod is connected
properly\f
. An iPod nano (1st Generation) may remain in fast
forward or rewind mode if it is connected during a
seek operation\f In this case\b please manually reset
the iPod\f .
An iPod nano (2nd Generation) will continue to
fast-forward or rewind if it is disconnected during
a seek operation\f
. An incorrect song title may appear when the Play
Mode is changed while using an iPod nano (2nd
Generation)
. Audiobooks may not play in the same order as
they appear on an iPod\f
. Large video files cause slow responses in an iPod\f
The vehicle center display may momentarily black
out\b but will soon recover\f
. If an iPod automatically selects large video files
while in the shuffle mode\b the vehicle center
display may momentarily black out\b but will soon
recover\f
BluetoothŠAudio player (if equipped)
.Some BluetoothŠaudio devices may not be used
with this system\f For detailed information about
Bluetooth
Šaudio devices that are available for use
with this system\b contact a RENAULT dealer\f
. Before using a Bluetooth
Šaudio system\b the initial
registration process for the audio device is
necessary\f
. Operation of the Bluetooth
Šaudio system may
vary depending on the audio device that is
connected\f Confirm the operation procedure
before use\f
. The playback of Bluetooth
Šaudio will be paused
under the following conditions\f The playback will
be resumed after the following conditions are
completed\f
— while using a Hands-free phone
— while checking a connection with a cellular phone
Heater and air conditioner, and audio system4-9
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-16Heater and air conditioner, and audio system
FM-AM RADIO WITH COMPACT DISC (CD) P\fAYER (Ty\be A)
SAA3122
1. MUTE button
2. FM radio band select button
3. AM radio band select button
4. CD button
5. AUX button
6. CD EJECT button
7. MENU button
8. SEEK/TRACK button9. TUNE/FF (Forward)·REW (Rewind)/FO\fDER
button
10. SCAN button
11. RDM (Random) button
12. Power button/VO\f (Volume) control knob
13. AUX IN (auxiliary in\but) jack
14. RPT (Re\beat) button
15. AUTO.P (Automatic Preset) button 16. Radio memory buttons (1 - 6)
17. DISP (Dis\blay) button
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-20Heater and air conditioner, and audio system
3. The switch number \fnd frequenc\b will \fppe\fr onthe displ\f\b when the memor\b is stored properl\b.
4. Perform steps 1 - 3 for \fll other memor\b buttons.
Push \f memor\b button (1 - 6) to select \f desired
memor\b.
If the b\ftter\b c\fble is disconnected, or if the \fudio fuse
blows, the r\fdio memor\b will be er\fsed. In such \f c\fse,
reset the desired st\ftions.
(Automatic Preset) button:
The \fudio s\bstem c\fn store up to 6 FM st\ftion
frequencies \fnd 6 AM st\ftion frequencies.
To store the st\ftion frequenc\b \futom\ftic\fll\b, push \fnd
hold the
button until \f beep sounds. The st\ftion
will be \futom\ftic\fll\b stored in the “AUTO.P” memor\b.
The displ\f\b indic\ftes “AP-**”.
Push the
button to select \f desired memor\b.
MUTE button:
Press the
button to mute the sound. Press \fg\fin
to restore the sound.
FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (T\bpe B)
JVH0060X
1. MUTE button
2. FM r\fdio b\fnd select button
3. AM r\fdio b\fnd select button
4. CD button
5. AUX button
6. CD EJECT button
7. Sound preference button
8. SEEK/TRACK button 9. TUNE/FF (Forw\frd)·REW (Rewind)/FOLDER
button
10. SCAN button
11. RDM (R\fndom) button
12. Power button/VOL (Volume) control knob
13. AUX IN (\fuxili\fr\b input) j\fck
14. RPT (Repe\ft) button
15. AUTO.P (Autom\ftic Preset) button
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
WARNING:
.Depending on the external device, please
note that the volume may be louder or
quieter than that of the external device.
. When the AUX contacts with the plug of the
connector cable, noise may be heard.
. The connected exterior device cannot be
operated with the main audio system. The
volume and sound quality can be adjusted.
. The song title in the external device cannot
be displayed on the audio display.
. For the power source of the external device,
use the special battery. The external device
cannot be charged with the AUX terminal.
Noise may be heard if the CD, radio etc. is
operated while charging the battery with the
power socket of the vehicle.
FM-AM radio operation
JVH0002X
\fhe audio s\bstem operates when the ignition switch is
in the “ACC” or “ON” position.
/button:
When the
/button is pushed while the audio
s\bstem is off, the audio s\bstem will turn on and the
radio will turn on.
When the
/button is pushed while another
audio source is pla\bing, the another audio source will
turn off and the radio will turn on.
\fo change the radio bands, push the
/button
until the desired band (FM1, FM2, or AM) is displa\bed.
\fhe FM stereo indicator, “S\f” will displa\b during FM
stereo reception. When the stereo broadcast signal is
weak, the radio will automaticall\b change from stereo
to monaural reception.
TUNE/FF·REW/FOLDER button:
When adjusting the broadcasting station frequenc\b
manuall\b, push the
orbutton until the desired
frequenc\b is achieved.
When adjusting the broadcasting station frequenc\b
automaticall\b, push the
orbutton. When the
s\bstem detects a broadcasting station, it will stop at
the station.
SEEK UP/DOWN button:
When adjusting the broadcasting station frequenc\b
automaticall\b, push the
button. When the
s\bstem detects a broadcasting station, it will stop at
the station.
button:
When the
button is pushed, the s\bstem will seek
and stop at the detected broadcasting station for 5
seconds, and then it will start to seek for the next
broadcasting station.
Push the
button in this 5-second period to stop
seeking.
Radio memory button:
\fhe audio s\bstem can store up to 12 FM station
frequencies (for FM1 and FM2) and 6 AM station
frequencies.
\fo store the station frequenc\b:
1. \fune to the desired broadcasting station fre- quenc\b b\b using the
orbutton.
2. Push and hold a memor\b button (1 - 6) until a beep sounds.
3. \fhe switch number and frequenc\b will appear on the displa\b when the memor\b is stored properl\b.
4. Perform steps 1 - 3 for all other memor\b buttons.
Push a memor\b button (1 - 6) to select a desired
memor\b.
If the batter\b cable is disconnected, or if the audio fuse
blows, the radio memor\b will be erased. In such a case,
reset the desired stations.
(Automatic Preset) button:
\fhe audio s\bstem can store up to 6 FM station
frequencies and 6 AM station frequencies.
\fo store the station frequenc\b automaticall\b, push and
hold the
button until a beep sounds. \fhe station
will be automaticall\b stored in the “AU\fO.P” memor\b.
\fhe displa\b indicates “AP-**”.
Heater and air conditioner, and audio system4-23
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
16. Radio memory buttons
17. RP\f (Repeat)\bMIX (Mix play) button
Anti-theft system (if equipped)
\fhis unit can only be activated when the ignition switch
for Anti-\fheft System is in the “ACC” or “ON” position.
Each radio is uniquely matched to the vehicle’s
immobilizer and therefore cannot be transferred to
any other vehicle.
Audio main operation
\fhe audio system operates when the ignition switch is
in the “ACC” or “ON” position.
POWER ON/OFF button:
\fo turn on the audio system, push the POWER ON\b
OFF button.
.\fhe system will turn on in the mode, (radio or CD)
which was used immediately before the system
was turned off.
. If there is no CD loaded, the radio will be turned
on.
\fo turn off the audio system, push the POWER ON\b
OFF button.
Volume control:
\fo control the volume, turn the VOLUME control dial.
\furn the VOLUME control dial clockwise to make the
sound louder.
\furn the VOLUME control dial counterclockwise to
make the sound quieter.
Sound preference button:
\fo enter the audio mode (radio or CD) , push the
button. When no CD is loaded, the audio system will
automatically switch to the radio mode. \fo change the audio settings (BASS, \fREBLE,
FADER, BALANCE, EQ) , push the
button or
EN\fER button to select the mode.
BASS ?\fREBLE ?BALANCE ?FADER ?EQ ?
BASS
\fo adjust each audio setting, turn the VOL control dial
clockwise or counterclockwise.
BASS: (í) to decrease \b (+) to increase
\fREB(LE): (í) to decrease \b (+) to increase
BAL(ANCE): (R) to right balance \b (L) to left balance
FADE(R): (F) to front fade \b (R) to rear fade
EQ (Equalizer): Use this control to change the preset
sound mode for CD play.
\furn the MENU\bVOL dial clockwise or counterclock-
wise. \fhe mode will change as follows:
OFF ⇔ENHANCE
If the audio settings mode is unchanged for approxi-
mately 8 seconds, the audio settings mode will
automatically return to the normal mode.
MENU button:
\fo configure the SPEED volume and BEEP settings,
perform the following procedure:
1. Push the MENU button.
2. \furn the VOLUME dial clockwise or counter- clockwise. \fhe display message will change as
follows:
PHONE SE\fUP ⇔SPEED VOL⇔CLOCK ⇔
BEEP ⇔PHONE SE\fUP
. When SPEED VOL appears on the display, briefly
push on the EN\fER button then turn the VOLUME
dial clockwise or counterclockwise to adjust the
level of the volume. Adjusting the setting to 0 (zero) turns off the
speed volume feature. Increasing the speed
volume setting results in the audio volume
increasing more rapidly with vehicle speed. Push
the EN\fER button again to save the setting.
. When BEEP appears on the display, briefly push
the EN\fER button and then turn the VOLUME dial
clockwise or counterclockwise to switch the beep
sound on or off. Push the EN\fER button again to
save the setting.
\fo configure Alternative Frequency, Regional and
Language settings, perform the following procedure:
1. Push and hold the MENU button for at least 1.5 seconds.
2. \furn the VOLUME dial clockwise or counter- clockwise. \fhe display message will change as
follows:
AF⇔REG ⇔LANGUAGE ⇔AF
. \fo activate or deactivate the AF and REG mode,
briefly push on the EN\fER button when AF or
REG appears on the display and turn the
VOLUME dial clockwise or counterclockwise to
switch between the off or on position. After
selection, push the EN\fER button to confirm the
settings.
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes weak.
— When the REG mode is enabled, the audio unit will maintain and hold the station which is
broadcasting local (regional) programmes.
. \fo change the display language, briefly push the
EN\fER button when LANGUAGE appears on the
display then turn the VOLUME dial clockwise or
counterclockwise to select the appropriate lan-
guage setting.
Heater and air conditioner, and audio system4-25
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
RPT TRACK: The CD player plays the curre\ft track
co\fti\fuously\b
RPT ALL: All the tracks o\f the CD will be played i\f
seque\ftial order\b
MIX DISC: All the tracks o\f the CD will be played i\f a
ra\fdom order\b
CD EJECT button:
Whe\f the
butto\f is pushed while a CD is loaded,
the CD will be ejected\b
Whe\f the
butto\f is pushed twice, the CD will be
ejected further, a\fd the CD ca\f be removed with ease\b
If a CD is ejected by pushi\fg the
butto\f, a\fd it is
\fot take\f out from the loadi\fg slot, the CD will
automatically be reloaded to the slot to protect the CD\b
AUX button:
The AUX IN jack is located o\f the audio u\fit\b The AUX
IN audio i\fput jack accepts a\fy sta\fdard a\falog audio
i\fput such as from a portable cassette tape/CD player,
MP3 player, laptop computers, etc\b
Push the AUX butto\f to play a compatible device whe\f
it is plugged i\fto the AUX IN jack\b
CAUTION:
. Do not allow the cable or an external device
connected to the AUX terminal to affect your
driving.
. Connect a stereo mini-plug (3.5 mm in
diameter) cable to the AUX IN jack. If a
monaural mini-plug cable is used, the audio
will not output correctly.
WARNING:
.Depending on the external device, please
note that the volume may be louder or
quieter than that of the external device.
. When the AUX contacts with the plug of the
connector cable, noise may be heard.
. The connected exterior device cannot be
operated with the main audio system. The
volume and sound quality can be adjusted.
. The song title in the external device cannot
be displayed on the audio display.
. For the power source of the external device,
use the special battery. The external device
cannot be charged with the AUX terminal.
Noise may be heard if the CD, radio etc. is
operated while charging the battery with the
power socket of the vehicle.
FM-AM radio operatio\f
JVH0004X
The audio system operates whe\f the ig\fitio\f switch is
i\f the “ACC” or “ON” positio\f\b
FM-AM button:
Whe\f the
butto\f is pushed while the audio
system is off, the audio system will tur\f o\f a\fd the
radio will tur\f o\f\b Whe\f the
butto\f is pushed
while CD is already operati\fg, it will automatically tur\f
off, a\fd the radio will tur\f o\f\b
To cha\fge the radio ba\fds, push the
butto\f u\ftil
the desired ba\fd appears\b
FM 1 ?FM 2 ?FM T ?MW ?LW
Duri\fg FM receptio\f, whe\f the
butto\f is pushed
for lo\fger tha\f 1\b5 seco\fds, statio\fs are searched for
a\fd the 6 statio\fs of the FM T ba\fd\b The sou\fd is
muted u\ftil the auto store operatio\f is completed,
upo\f which preset cha\f\fel 1 is automatically tu\fed i\f\b
TUNE button:
Whe\f adjusti\fg the broadcasti\fg statio\f freque\fcy
ma\fually, push the
butto\f u\ftil the desired
freque\fcy is achieved\b
The freque\fcy cha\fges i\f steps of 100 kHz o\f the FM
ba\fd, 9 kHz o\f the MW ba\fd, a\fd 3 kHz o\f the LW
ba\fd\b
SEEK button:
Whe\f adjusti\fg the broadcasti\fg statio\f freque\fcy
automatically, push the
butto\f\b Whe\f the
system detects a broadcasti\fg statio\f, it will stop at
the statio\f\b
Heater and air conditioner, and audio system4-27
&RQGLWLRQ