2012 RENAULT PULSE change key battery


> (GLW    0RGHO .$2(0B5HQDXOW @
2-30Instruments and controls
position
Theposition turns on the headlights in addition to
the other lights\f
Headlight beam
\bIC3785
To turn on the high beam, push the lever towards the
front position*1\f
To turn off the high beam, return the lever to the neutral
position
*2\f
To flash the headlights, pull the lever towards the
rearmost position
*3\f The headlights can be flashed
even when the headlights are not on\f If equipped, when the lever is pulled towards the
rearmost position
*3after the ignition switch is
placed in the “OFF” or “LOCK” position, the headlight
will turn on and stay on for 30 seconds\f The lever can
be pulled 4 times for up to 2 minutes\f
Daytime light system (if equipped)
Even if the headlight switch is off, the daytime lights
will come on after starting the engine\f However, you
cannot change low beam to high beam when the light
switch is off\f
When the light switch is turned to the
position,
the headlight low beam will turn off\f
BATTERY \bAVER \bY\bTEM
The light reminder chime will sound if the driver’s door
is opened while the following improper operations
occur:
. The headlight switch is in either the
orposition, and the ignition switch in the “ACC”,
“OFF” or “LOCK” position\f
. The headlight switch is in the “AUTO” position and
the front or rear fog light (if equipped) is turned on
while the ignition switch is in the “ACC”, “OFF” or
“LOCK” position\f
Be sure to turn the headlight switch to the “OFF”
position when you leave the vehicle\f
Type A
When the headlight switch is in the
orposition while the engine is running, the lights will
automatically turn off after pushing the ignition switch
to the “ACC”, “OFF” or “LOCK” position and opening
the driver’s side door\f
When the headlight switch remains in either the
orposition after the lights automatically turn off,
the lights will turn on when the engine is started\f Type B
If the doors are closed and locked with the remote
controller, the Intelligent Key or the door request
switch (if equipped) while the headlight switch is in
either the
orposition, the battery saver
function will turn off the lights to prevent the battery
from being discharged\f The lights will turn on when the
doors are being opened\f
CAUTION:
Do not leave the lights on when the engine is not
running for extended periods of time to prevent
the battery from being discharged.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
3-10Pre-driving checks and adjustments
CAUTION:
.Do not allow the Intelligent Key, which
contains electrical components, to come
into contact with water or salt water. This
could affect the system function.
. Do not drop the Intelligent Key.
. Do not strike the Intelligent Key sharply
against another object.
. Do not change or modify the Intelligent Key.
. Wetting may damage the Intelligent Key. If
the Intelligent Key gets wet, immediately
wipe until it is completely dry.
. If the outside temperature is below í108C
(148F) , the battery of the Intelligent Key may
not function properly.
. Do not place the Intelligent Key for an
extended period in an area where tempera-
tures exceed 608C (1408F) .
. Do not attach the Intelligent Key with a key
holder that contains a magnet.
. Do not place the Intelligent Key near equip-
ment that produces a magnetic field, such as
a TV, audio equipment and personal compu-
ters or cellular phones.
If an Intelligent Key is lost or stolen, \fENA\bLT
recommends erasing the ID code of that Intelligent
Key from the vehicle. This may prevent the unauthor-
ized use of the Intelligent Key to operate the vehicle.
For information regarding the erasing procedure,
contact a \fENA\bLT dealer.
The Intelligent Key function can be disabled. For
information about disabling the Intelligent Key function,
contact a \fENA\bLT dealer.
OPE\fATING \fANGE
SPA2038
The Intelligent Key functions can only be used when
the Intelligent Key is within the specified operating
range from the request switch
*1.
When the Intelligent Key battery is discharged or
strong radio waves are present near the operating
location, the Intelligent Key system’s operating range
becomes narrower, and the Intelligent Key may not
function properly.
The operating range is within 80 cm (31.50 in) from
each request switch
*1.
If the Intelligent Key is too close to the door glass,
handle or rear bumper the request switches may not
function.
When the Intelligent Key is within the operating range,
it is possible for anyone, even someone who does not
carry the Intelligent Key, to push the request switch
and lock/unlock the doors.
\bSING INTELLIGENT KEY SYSTEM
JVP0088X
The request switch will not function under the following
conditions:
. When the Intelligent Key is left inside the vehicle
. When the Intelligent Key is not within the
operational range
. When any door is open or not closed securely
. When the Intelligent Key battery is discharged
. When the ignition switch is in the “ACC” or “ON”
position
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
.make a call via voice dialling by pushing thebutton \for more than 2 seconds then say
the voice tag clearly.
\bANDS-FREE TELEP\bONE OPERATION
(Type B)
JV\b0519X
Buttons:
1. Phone button
2. A-Z button
3. TUNE/MENU/ENTER dial
4. SETUP button
Microphone:
The microphone is located near the map light.
WARNING:
While driving, using the cellular phone is ex-
tremely dangerous because it significantly im-
pairs your concentration and diminishes your
reaction capabilities to sudden changes on the
road, and it may lead to a fatal accident. This
applies to all phone call situations such as when
receiving an incoming call, during a phone
conversation, when calling through the phone
book search, etc.
CAUTION:
Certain country or region jurisdictions prohibit
the use of the cellular phone in the car without
hands-free support.
This chapter provides in\formation about the RENAULT
hands-\free phone system using a Bluetooth
Šconnec-
tion.
Bluetooth
Šis a wireless radio communication stan-
dard. This system o\f\fers a hands-\free \feature \for your
cellular phone to enhance driving com\fort.
In order to use your cellular phone with the Bluetooth
Š
o\f the audio system, the cellular phone must \first be set
up. Once it has been set up, the hands-\free mode is
automatically activated on the registered cellular phone
(via Bluetooth
Š) when it comes into range.
A noti\fication message appears on the audio display
when the phone is connected, when an incoming call
is being received, as well as when a call is initiated.
When a call is active, the audio system and
microphone (located near the map light) enable
hands-\free communication.
I\f the audio system is in use at the time, the radio, CD,
or AUX source mode will be muted and will stay muted
until the active call has ended.
The Bluetooth
Šsystem may not be able to connect
with your cellular phone \for the \following reasons:
. The cellular phone is too \far away \from the vehicle.
. The Bluetooth
Šmode on the cellular phone has
not been activated.
. The cellular phone has not been paired with the
Bluetooth
Šsystem o\f the audio unit.
. The cellular phone does not support BluetoothŠ
technology (BT Core v1.2, \bands Free Pro\file v1.0
and Object Push Pro\file v1.0) . NOTE:
For details, see the cellular phone’s owner’s
manual.
\bands-\free phone setup
To set up the BluetoothŠsystem to pair with (connect
or register) a pre\ferred cellular phone, push the
button, select the BluetoothŠkey, and then push the
TUNE/MENU/ENTER dial. It is also possible to display
the set up menu directly by pushing the
button.
. Pair Device
Bluetooth
Šcellular phones can be paired with the
system. A maximum o\f 5 cellular phones can be
registered.
. Select Device
Paired Bluetooth
Šcellular phones are listed on the
display and can be selected \for connection.
. Delete Device
A registered Bluetooth
Šcellular phone can be
deleted.
. Bluetooth
I\f this setting is turned o\f\f, the connection between
the Bluetooth
Šdevices and the in-vehicle Blue-
toothŠmodule will be cancelled.
When success\fully paired, a noti\fication message will
be displayed. During the connection the \following
status icons will be displayed (top le\ft o\f display):
Signal strength (
) , Battery status () and
BluetoothŠ().
*: I\f the low battery message comes on, the BluetoothŠ
device must be recharged soon.
Heater and air conditioner, and audio system4-63
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-8Starting and driving
steering wheel slightly to the right and left.
(See “Vehicle information \fisplay\b (P.2-20) .)
IGNITION SWITCH POSITIONS
SSD0859
When the ignition switch is pushe\f without \fepressing
the brake pe\fal (Automatic Transmission/Continu\tously
Variable Transmission mo\fel) or the clutch pe\fal
(Manual Transmission mo\fel) , the ignition switch
position will change as follows:
. Push once to change to “ACC\b.
. Push two times to change to “ON\b.
. Push three times to change to “OFF\b.
. Push four times to return to “ACC\b.
. Open or close any \foor to return to “LOCK\b when
in the “OFF\b position.
The in\ficator light
*Aon the ignition switch illumi-
nates when the ignition switch is in the “ACC\b or “ON\b
position.
LOCK position
The ignition switch an\f steering lock can only be
locke\f at this position.
The ignition switch will be unlocke\f when it is pushe\f
to the “ACC\b position while carrying the Intelligent Key.
ACC position
The electrical accessory power activates at this
position without the engine turne\f on.
ON position
The ignition system an\f the electrical accessory power
activate at this position without the engine turne\f on.
OFF position
The engine is turne\f off with the steering wheel
unlocke\f.
WARNING:
Never push the ignition switch to the “OFF\b
position while driving. The steering wheel may
lock and cause the driver to lose control of the
vehicle, resulting in serious vehicle damage or
personal injury.
CAUTION:
Do not leave the vehicle for extended periods of
time when the ignition switch is in the “ACC” or
“ON” position and the engine is not running.
This can discharge the battery.
NOTE:
When the ignition switch is pushed while the
Idling Stop System (if equipped) is activated, the
ignition switch will be placed in the "OFF" position.
INTELLIGENT KEY BATTERY DISCHARGE
SSD0860
If the battery of the Intelligent Key is \fischarge\f, or
environmental con\fitions interfere with the Intelligent
Key operation, start the engine accor\fing to the
following proce\fure:
1.
Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the selector lever to the “P\b (Park) or “N\b
(Neutral) position.
Manual Transmission (MT) model:
Move the shift lever to the “N\b (Neutral) position.
2. Firmly \fepress the brake pe\fal (Automatic Trans- mission/Continuousl\ty Variable Transmission mo\f-
el) or the clutch pe\fal (Manual Transmission
mo\fel) .
3. Touch the ignition switch with the Intelligent Key as illustrate\f. (A chime will soun\f.)
4. Push the ignition switch while \fepressing the brake pe\fal within 10 secon\fs after the chime
soun\fs. The engine will start.
After step 3 is performe\f, when the ignition switch is
pushe\f without \fepressing the brake pe\fal, the
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
ignition switch position will change to “ACC”.
NOTE:
.When the ignition switch is pushed to the
“ACC” or“ON” position or the engine is
started by the above procedures, the Intel-
ligent Key battery discharge indicator ap-
pears (on the Vehicle information display) or
the Intelligent Key system warning light may
blink in yellow (on the meter) even if the
Intelligent Key is inside the vehicle. This is
not a malfunction. To stop the warning light
from blinking, touch the ignition switch with
the Intelligent Key again.
. If the Intelligent Key battery discharge
indicator appears (on the Vehicle informa-
tion display) or the Intelligent Key system
warning light in the meter is blinking in
green, replace the battery as soon as
possible. (See “Battery”(P.8-23) .)GA\fOLI\bE E\bGI\bE
1. Apply the parking brake.
2. Depress the foot brake pedal.
3.Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the selector lever to the “P” (Park) or “\b”
(\beutral) position.
The starter is designed to operate only when
the selector lever is in the proper position.
Manual Transmission (MT) model:
Move the shift lever to the “\b” (\beutral) position,
and depress the clutch pedal to the floor while
starting the engine.
The starter is designed to not operate unless
the clutch pedal is depressed.
4. Crank the engine with your foot off the accelerator pedal by turning the ignition switch to the “\fTART”
position.
5. Immediately release the ignition switch when the engine starts. If the engine starts, but fails to run,
repeat the above procedures.
If the engine is very hard to start in extremely cold
or hot weather, depress the accelerator pedal and
hold it to help start the engine.
CAUTION:
.Do not operate the starter for more than 15
seconds at a time. If the engine does not
start, turn the ignition switch off and wait 10
seconds before cranking the engine again.
Otherwise, the starter could be damaged.
. If it becomes necessary to start the engine
with a booster battery and jumper cables, the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
6. Allow the engine to idle for at least 30 seconds after starting the engine to warm-up. Drive at
moderate speeds for a short distance first,
especially in cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
DIE\fEL E\bGI\bE
1. Apply the parking brake.
2. Depress the foot brake pedal.
3. Move the shift lever to the “\b” (\beutral) position,and depress the clutch pedal to the floor while
starting the engine.
4. Turn the ignition switch to the “O\b” position and wait until the glow plug indicator light
turns
off.
5. Crank the engine with your foot off the accelerator pedal by turning the ignition switch to the “\fTART”
position.
6. Immediately release the ignition switch when the engine starts. If the engine starts, but fails to run,
repeat the above procedures.
CAUTION:
.Do not operate the starter for more than 20
seconds at a time. If the engine does not
start, turn the ignition switch off and wait 20
seconds before cranking the engine again.
Otherwise, the starter could be damaged.
Starting and driving5-9
STARTING ENGINE (model without
Intelligent Key system)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-16Starting and driving
P (Park):
Use this position when the vehicle is par\fed or when
starting the engine.Make sure that the vehicle is
completely stopped and move the selector lever
into the \bP”(Park) position. Apply the par\fing
bra\fe. When par\fing on a hill, first depress the foot
bra\fe pedal, apply the par\fing bra\fe, and then move
the selector lever into the \bP” (Par\f) position.
R (Reverse):
Use this position to bac\f up. Ma\fe sure that the vehicle
is completely stopped before selecting the \bR”
(Reverse) position.
N (Neutral):
Neither the forward nor reverse gear is engaged. The
engine can be started in this position. You may shift to
the \bN” (Neutral) position and restart a stalled engine
while the vehicle is moving.
D (Drive):
Use this position for all normal forward driving.
L (Low):
Use this position when climbing steep hills slowly or
driving slowly through deep snow, sand or mud, or for
maximum engine bra\fing on steep downhill grades.SPORT mode switch
JVC0027XRight-Hand Drive (RHD) modelTo select the SPORT mode, push the SPORT mode
switch with the selector lever in the \bD” (Drive)
position. The SPORT mode indicator light
in the
meter panel illuminates. To turn off the SPORT mode,
push the SPORT mode switch again. The SPORT
mode indicator light will turn off. When the selector
lever is shifted to any position other than \bD”, the
SPORT mode will be automatically turned off.
“OFF” position:
For normal driving and fuel economy, use the \bOFF”
position.
“ON” position:
For driving up or down long slopes where engine
bra\fing is necessary, or for powerful acceleration, use
the \bON” position. The transmission will automatically
select a different gear ratio, allowing the engine to
provide high output.
When driving conditions change, push the switch to
turn the SPORT mode off.
Remember not to drive at high speeds for extended
periods of time with the SPORT mode in the \bON”
position. This reduces fuel economy.
Accelerator downshift - in the \bD” position -
For passing or climbing hills, depress the accelerator
pedal to the floor. This shifts the transmission down
into a lower gear, depending on the vehicle speed.
Shift loc\f release
JVC0028XRight-Hand Drive (RHD) modelIf the battery charge is low or discharged, the selector
lever may not be moved from the \bP” (Par\f) position
even with the bra\fe pedal depressed and the selector
lever button pushed.
To move the selector lever, perform the following
procedure:
1. Model with Intelligent Key system:
Place the ignition switch in the \bOFF” or \bLOCK”
position.
Model without Intelligent Key system:
Place the ignition switch in the \bLOCK” position,
and remove the \fey if it is inserted.
2. Apply the par\fing bra\fe.
3. Depress the shift loc\f release button.
4. Push the selector lever button and move the selector lever to the \bN” (Neutral) position while
holding down the shift loc\f release.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
JVM0105X
To replace the battery\f
1. Remo\be the screw
*A.
2. Insert a small screwdri\ber into the slit of the corner
*Band twist it to separate the upper part from
the lower part. Use a cloth to protect the casing.
3. Replace the battery with a new one.
Recommended battery\f CR1620 or equi\balent
.Do not touch the internal circuit and electricterminals as doing so could cause a malfunc-
tion.
.Make sure that the + side faces the bottom ofthe case*C.
4. Close the lid and install the screw securely.
5. Operate the buttons to check its operation.
See a RENAULT dealer if you need assistance for
replacement.
FCC WARNING:
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions; (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interference
that may cause undesired operation of the
device.
INTELLIGENT KEY BATTERY
Battery replacement
CAUTION:
. Be careful not to allow children to swallow
the battery and removed parts.
. An improperly disposed battery can harm
the environment. Always confirm local reg-
ulations for battery disposal.
. When changing batteries, do not let dust or
oil get on the components.
. There is danger of explosion if lithium
battery is incorrectly replaced. Replace only
with the same or equivalent type.
SDI2451
To replace the battery\f
1. Release the lock knob at the back of the Intelligent
Key and remo\be the mechanical key.
2. Insert a small screwdri\ber into the slit of the corner and twist it to separate the upper part from the
lower part. Use a cloth to protect the casing.
3. Replace the battery with a new one.
.Recommended battery\f CR2025 or equi\balent.Do not touch the internal circuit and electric terminals as doing so could cause a malfunc-
tion.
Maintenance and do-it-yourself8-25
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
I
Idling Stop System ..................\9..................\9................. 5-19
Ignition s\fitchKey positions..................\9..................\9..................\9...... 5-\b
Ignition s\fitch (model \fithout intelligent
Key system) ..................\9..................\9.....................\9........... 5-5
Ignition s\fitch positions.........\9..................\9..................\9. 5-8
Indicator lights..................\9..................\9.....................\9..... 2-1\b
Injured persons..................\9..................\9..................\9........ 1-9
Inside rearvie\f mirror..................\9..................\9............. 3-20
Installing spare tire..................\9..................\9.................... \b-4
Instrument panel.............\9..................\9............................. 2-2
Intelligent Key..................\9..................\9............................. 3-3
Intelligent key battery..................\9..................\9.............. 8-25
Intelligent Key battery discharge..................\9............. 5-8
Intelligent Key battery discharge indicator............ 2-21
Intelligent Key system ..................\9..................\9..... 3-9, 5-\b Intelligent Key system \farning light................ 2-14
Interior lights..................\9..................\9................. 2-42, 8-29
J
Jump starting..................\9..................\9..................\9............ \b-8
K
Key..................\9..................\9..................\9.......................\9....... 3-2 Anti-Theft System* key..................\9..................\9....... 3-2
Ignition s\fitch (model \fithout intelligent
Key system) ..................\9..................\9.....................\9..... 5-5
Ignition s\fitch positions.........\9..................\9............. 5-8
Intelligent key battery..................\9..................\9....... 8-25
Intelligent Key battery discharge..................\9....... 5-8
Intelligent Key system ..................\9................. 3-9, 5-\b
Keys..................\9..................\9...............................\9......... 3-2
Locking \fith key..................\9..................\9.................. 3-5
Mechanical key ..................\9..................\9..................\9.. 3-4
Push-button ignition s\fitch
(model \fith Intelligent Key system)..................\9.. 5-\b
Remote keyless entry system..................\9............. 3-7 Using intelligent Key system ..................\9.. 3-7, 3-10
Using remote keyless entry function............... 3-15
Key positions..................\9..................\9..................\9............ 5-\b
L
Labels Air conditioner specification label..................\9..... 9-8
Engine serial number..................\9..................\9.......... 9-8
Vehicle identification number (VIN) ..................\9.. 9-7
Light Bulb replacement..................\9..................\9.... 8-2, 8-28
Exterior lights..................\9..................\9..................\9... 8-29
Fog light s\fitch..................\9..................\9................ 2-32
Front fog lights..................\9..................\9..................\9 2-32
Front map lights..................\9..................\9................ 2-42
Headlight aiming control ..................\9..................\9 2-31
Headlight and turn signal s\fitch ..................\9... 2-29
Headlight s\fitch..................\9..................\9............... 2-29
Headlights..................\9..................\9..................\9........ 8-28
Indicator lights..................\9..................\9................... 2-1\b
Interior lights..................\9..................\9........... 2-42, 8-29
Light locations..................\9..................\9................... 8-30
Replacement..................\9..................\9............. 8-2, 8-28
Room light..................\9..................\9..................\9........ 2-42
Warning lights..................\9..................\9................... 2-13
Lock Anti-lock Braking System (ABS) ..................\9... 5-37
Child safety rear door lock..................\9................. 3-7
Door locks..................\9..................\9..................\9........... 3-4
Locking \fith inside lock knob ..................\9........... 3-5
Locking \fith key..................\9..................\9.................. 3-5
Locking \fith po\fer door lock s\fitch................ 3-\b
Steering lock ..................\9..................\9............... 5-\b, 5-7
Vehicle speed sensing door
lock mechanism..................\9..................\9................... 3-\b
Lock, Back door lock..................\9..................\9............. 3-19
LW-MW-FM radio operation..................\9...... 4-37, 4-43
LW-MW-FM radio \fith compact disc (CD)
changer (Type F)..................\9..................\9..................\9... 4-40 LW-MW-FM radio \fith compact disc (CD)
player (Type E)..................\9..................\9..................\9....... 4-35
M
Maintenance
Battery..................\9..................\9........................ 8-3, 8-23
Explanation of general maintenance items ....... 8-2
General maintenance ..................\9..................\9......... 8-2
Indicators for maintenance (dot matrix).......... 2-24
Maintenance precautions..................\9..................\9.. 8-4
Maintenance requirements..................\9..................\9 8-2
Scheduled maintenance.......\9..................\9............... 8-2
Seat belt maintenance..................\9..................\9.... 1-13
Malfunction indicator light (MIL)..................\9............ 2-17
Manual air conditioner..................\9..................\9.............. 4-4
Manual transmission..................\9..................\9................. 5-5
Mechanical key ..................\9..................\9..................\9........ 3-4
Mechanical Key LOCK \farning..................\9............. 2-21
Meter display model..................\9..................\9............... 2-38
Meters and gauges..................\9..................\9................... 2-\b
Mirror Inside rearvie\f mirror..................\9..................\9...... 3-20
Mirrors..................\9..................\9...............................\9.. 3-20
Outside rearvie\f mirrors..................\9..................\9 3-21
Vanity mirrors..................\9..................\9..................\9... 3-23
N
Ne\f vehicle break-in..................\9..................\9................ 5-3
No key \farning..................\9..................\9..................\9...... 2-21
O
Odometer..................\9..................\9.....................\9............... 2-8
OilChanging engine oil and oil filter............\9......... 8-10
Checking engine oil level.............\9..................\9.... 8-10
Engine oil..................\9..................\9..........................\9.. 8-10
Engine oil replacement indicator..................\9.... 2-24
Oil filter replacement indicator ..................\9....... 2-24
10-3
&RQGLWLRQ