2012 RENAULT PULSE reset


> (GLW    0RGHO .$2(0B5HQDXOW @
2-26Instruments and controls
The display is updated every 30 se\fonds. \bt about the
first 500 m after a reset, the display shows “——”.
Speed:
The average speed mode shows the average vehi\fle
speed sin\fe the last reset. Resetting is done by
pushing the
swit\fh*Bfor longer than 1 se\fond.
(The average fuel \fonsumption is also reset at the
same time.)
The display is updated every 30 se\fonds. The first 30
se\fonds after a reset, the display shows “——”.
Elapsed time and trip odometer (km or
MILES)
JVI0033X
Elapsed time:
The elapsed time mode shows the time sin\fe the last
reset. The displayed time \fan be reset by pushing the
swit\fh*Bfor longer than 1 se\fond. (The trip
odometer is also reset at the same time.)
Trip odometer (if equipped) :
The trip odometer mode shows the distan\fe that the
vehi\fle has been driven sin\fe the last reset. Resetting
is done by pushing the
swit\fh*Bfor longer than
1 se\fond. (The elapsed time is also reset at the same
time.)
Distan\fe to empty (km or MILES)
JVI0010X
The distan\fe to empty (dte) mode provides you with an
estimation of the distan\fe that \fan be driven before
refueling. The dte is \fonstantly being \fal\fulated, based
on the amount of fuel in the fuel tank and the a\ftual fuel
\fonsumption.
The display is updated every 30 se\fonds.
The dte mode in\fludes a low range warning feature. If
the fuel level is low, the warning is displayed on the
s\freen.
When the fuel level drops even lower, the dte display
will \fhange to “——”.
. If the amount of fuel added is small, the
display just before the ignition switch is
pushed to the “OFF”position may continue
to be displayed.
. When driving uphill or rounding curves, the
fuel in the tank shifts, which may momenta-
rily change the display.
Outside air temperature (8C) (if equipped)
JVI0012X
The outside air temperature is displayed in 8C in the
range of í30 to 608C.
The outside air temperature mode in\fludes a low
temperature warning feature. If the outside air tem-
perature is 38 C or below, the warning “ICY” is
displayed on the s\freen.
The outside temperature sensor is lo\fated in front of
the radiator. The sensor may be affe\fted by road or
engine heat, wind dire\ftions and other driving \fondi-
tions. The display may differ from the a\ftual outside
temperature or the temperature displayed on various
signs or billboards.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Accumulated time and current saved fuel
consumption (ml (mililiter)) \fy Idling \btop
\bystem (if equipped for Thailand)
JVI0011XType A
JVC0021XType BTheswitch*Bis used in the setting mode to
select and decide a menu of Type A and B.
Accumulated time (Type A):
The Accumulated time mode shows the accumulated
time Idling \btop \bystem has \feen operated since the
last reset.
Resetting is done \fy pushing the
switch*Bfor
longer than 1 second. (The saved fuel is also reset at
the same time.) Current saved fuel consumption (Type A):
The Current saved fuel consumption mode shows the
current saved fuel consumption \fy Idling \btop \bystem
has \feen operated since the last reset.
Accumulated time (Type B):
The Accumulated time mode shows the accumulated
time Idling \btop \bystem has \feen operated since the
time the ignition switch was turned ON.
Resetting is done \fy pushing the
switch*Bfor
longer than 1 second. (The saved fuel is also reset at
the same time.)
Current saved fuel consumption (Type B):
The Current saved fuel consumption mode shows the
current saved fuel consumption \fy Idling \btop \bystem
has \feen operated since the time the ignition switch
was turned ON. \bee “Idling \btop \bystem (if equipped
for Thailand)” (P.5-19) .
\betting
JVI0013X
Setting cannot be made while driving. A mes-
sage “Setting can only be operated when
stopped” is also displayed on the vehicle
information display.
The
switch*Aandswitch*Bare used in the setting mode to select and set a menu.
SKIP:
Push the
switch*Ato move to the warning
check mode.
Push the
switch*Bto select other menus.
ALERT:
The alert menu can \fe set to notify the following items.
. TIMER
\belect this su\fmenu to specify when the "time to
rest" indicator activates.
. ICY
\belect this su\fmenu to display the low outside
temperature warning.
To return to the top page of the setting mode, select
“BACK”.
TIME SETTING (CURRENT TIME) :
. CURRENT TIME
Adjust the date and time (hour and minute) of the
clock on the meter.
TIME SETTING (Birthday and Anniversary):
The \firthday and anniversary message reminds you of
the anniversary or a \firthday the driver should
remem\fer.
. BIRTHDAY
\belect this su\fmenu to adjust the date of the
Birthday message.
. ANNIVER\bARY
\belect this su\fmenu to adjust the date of the
Anniversary message.
\belect the display image to set the desired display
image of the Anniversary message.
Instruments and controls2-27
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
2-28Instruments and controls
.WEDDING DAY
Select this s\fbmen\f t\b adj\fst the date \bf the
wedding day message.
MAINTENANCE:
The maintenance intervals \bf the f\bll\bwing items can
be set \br reset f\br the reminders.
. OIL
Select this s\fbmen\f t\b set \br reset the distance
f\br changing the engine \bil.
. FILTER
Select this s\fbmen\f t\b set \br reset the distance
f\br replacing the \bil filter.
. TIRE
Select this s\fbmen\f t\b set \br reset the distance
f\br replacing tires.
. OTHER
Select this s\fbmen\f and set \br reset the distance
f\br replacing items \bther than the engine \bil, \bil
filter and tires.
T\b ret\frn t\b the t\bp page \bf the setting m\bde, select
“BACK”.
OPTIONS (UNIT) (except for Hong Kong):
The \bpti\bn men\f bel\bw can be set t\b y\b\fr preference.
. UNIT
Select this s\fbmen\f t\b ch\b\bse the \fnit.
. LANGUAGE
Select this s\fbmen\f t\b ch\b\bse the display
lang\fage.
. STOP/START (if eq\fipped f\br E\fr\bpe)
Select this s\fbmen\f t\b ch\b\bse the CO2 savings
\br the engine st\bp time \fsing the St\bp/Start
System.
(See “St\bp/Start System (CO2 savings ) (if
eq\fipped f\br E\fr\bpe)” (P.2-28) .) T\b ret\frn t\b the t\bp page \bf the setting m\bde, select
“BACK”.
Warning check
JVI0014X
T\b see if there are any \bf the f\bll\bwing warnings and
c\brresp\bnding details, select this men\f.
.
Seat belt warning
. N\b key warning
. L\bw f\fel warning
. Parking brake release warning
. D\b\br/back d\b\br \bpen warning
SKIP:
P\fsh the
switch*At\b m\bve t\b the warning
check m\bde.
P\fsh the
switch*Bt\b select \bther men\fs.
ALERT:
This item is available \bnly when a warning is displayed.
Select this men\f t\b see the details \bf warnings.
Resetting displays
When the average f\fel c\bns\fmpti\bn, average speed,
elapsed time is displayed, p\fsh the trip c\bmp\fter
m\bde switch
*Af\br l\bnger than 3 sec\bnds. The
display \bf average f\fel c\bns\fmpti\bn, average speed,
elapsed time, trip \bd\bmeter, acc\fm\flated time (f\br
Idling St\bp System) and c\frrent saved f\fel c\bns\fmp-
ti\bn (f\br Idling St\bp System) will be reset at the same
time.
STOP/START SYSTEM (CO2 savings ) (if
eq\fipped f\br E\fr\bpe)
JVI0269XType A
JVI0270XType BThe CO2 savings and the engine st\bp time (f\br Type
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
B) using the Stop/Start System are kept in a su\fmenu.
Trip Saving \bType A)
The Trip Saving mode shows the estimated CO2
exhaust emissions prevented since last reset.
It is possi\fle to reset using the [RESET] su\fmenu then
push the
switch*Ato set to zero.
NOTE:
The [Trip Saving] value is the same information
that is displayed when the engine is automati-
cally stopped by the Stop/Start System.
Total Saving \bType B)
The Total Saving mode shows:
. The estimated CO2 exhaust emissions prevented.
. The time that the engine has \feen stopped \fy the
Stop/Start System.
NOTE:
The [Total Saving] values cannot be reset and
show accumulated Stop/Start System informa-
tion since the vehicle was built.
HEADLIGHT SWITCH
SIC3782Type A
SIC3783Type BRENAULT recommends that you consult the local
regulations concerning the use of lights.
AUTO position \bif equipped)
When the ignition switch is in the “ON” position and
the headlight switch is in the “AUTO” position, the
headlights, front clearance lights, instrument panel
lights, rear com\fination light, and other lights turn on
automatically depending on the \frightness of the
surroundings.
The headlights will turn on automatically at twilight or in rainy weather \bwhen the windshield wiper is operated
continuously) \bfor Hong Kong) .
When the ignition switch is turned to the “OFF”
position, the lights will turn off automatically.
JVI0023X
CAUTION:
Do not place any objects on top of the sensor*A. The sensor senses the brightness level and
controls the autolight function. If the sensor is
covered, it reacts as if it is dark, and the
headlights will illuminate.
position
Theposition turns on the front clearance lights,
instrument panel lights, rear com\fination lights and
other lights.
Instruments and controls2-29
HEADLIGHT AND TURN SIGNAL
SWITCH
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
HEADLIGHT AIMING CONTROL (if
equi\f\fed)
Ma\bual ty\fe
SIC2275
The headlight aimi\bg co\btrol o\ferates whe\b the
ig\bitio\b switch is i\b the “ON” \fositio\b a\bd the headlight
is o\b to allow the headlight axis to be adjusted
accordi\bg to the drivi\bg co\bditio\b.
Whe\b drivi\bg with \bo heavy load/luggage or drivi\bg o\b
a flat road, select the \bormal \fositio\b “0”.
If the \bumber of occu\fa\bts a\bd load/luggage i\b the
vehicle cha\bges, the headlight axis may become higher
tha\b \bormal.
If the vehicle is traveli\bg o\b a hilly road, the headlights
may directly shi\be o\b the rearview a\bd outside mirrors
of a vehicle ahead or the wi\bdshield of a\b o\bcomi\bg
vehicle, which may obscure other drivers’ visio\b.
To adjust to the \fro\fer aimi\bg height, tur\b the switch
accordi\bgly. The higher the \bumber, desig\bated o\b the
switch, the lower the headlight axis.
Select the switch \fositio\b by referri\bg to the followi\bg
sam\fles.
Switch \fo-sitio\b Number of
fro\bt seat
occu\fa\bts Number of
rear seat
occu\fa\bts Weight of load i\b lug-
gage com\fartme\bt
0 1 or 2 No occu-
\fa\bts No load
1 2 3 No load
22 3 A\f\froximately 48 kg
(106 lb)
31 No occu-
\fa\bts A\f\froximately 279 kg
(615 lb)
TURN SIGNAL SWITCH
SIC3786
CAUTION:
The turn signal switch will not be cancelled
automatically if the steering wheel turning angle
does not exceed the preset amount. After the
turn or lane change, make sure that the turn
signal switch is returned to its original position.
Tur\b sig\bal
To tur\b o\b the tur\b sig\bals, move the lever u\f*1or
dow\b*2towards the desired directio\b. Whe\b the
tur\b is com\fleted, the tur\b sig\bal ca\bcels automati-
cally.
La\be cha\bge sig\bal
To tur\b o\b the la\be cha\bge sig\bals, move the lever u\f*1or dow\b*2towards the desired directio\b.
If the lever is moved back right after movi\bg u\f
*1or
dow\b*2, the light will flash 3 times (if equi\f\fed) .
To ca\bcel the flashi\bg, move the lever to the o\f\fosite
directio\b.
Instruments and controls2-31
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Washer operation
To operate the washer, push the lever toward the front
of the vehi\fle*3until the desired amount of washer
fluid is spread on the rear window. The wiper will
automati\fally operate several times.
\bIC4127Type A
\bIC4145Type BThe rear window defogger swit\fh operates when the
ignition swit\fh is in the “ON” position.
The defogger is used to redu\fe the moisture, fog or
frost on the rear window surfa\fe and outside door
mirror surfa\fe (if equipped) to improve the rear view.
When the defogger swit\fh
*1is pushed, the indi\fator
light*2illuminates and the defogger operates for
approximately 15 minutes. After the preset time has
passed, the defogger will turn off automati\fally.
To turn off the defogger manually, push the defogger
swit\fh again.
CAUTION:
. When operating the defogger continuously,
be sure to start the engine. Otherwise, it may
cause the battery to discharge.
. When cleaning the inner side of the window,
be careful not to scratch or damage the
electrical conductors on the surface of the
window.
NOTE:
When the rear defogger is turned on, the Stop/
Start (Idling Stop) System (if equipped) will not
be activated.
Instruments and controls2-35
DEFOGGER SWITCH (if equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Driver’s window switch
The driver’s switch, which is the main switch, can
control all windows\f
Locking passengers’ windows:
JVI\b\b36XFront and rear typeWhen the lock button*1is pushed in, the passen-
gers’ windows cannot be operated\f
To cancel the passengers’ windows lock, push the lock
button
*1again\f
Passenger’s window switch
SIC2311
The passenger’s switch can control its corresponding
window\f When the passengers’ windows lock button on the
driver’s switch is pushed in, the passenger’s switch
cannot be operated\f
Automatic function
JVI\b\b37XFront and rear typeAutomatic function is available for the switch that has
anmark on its surface\f
The automatic function enables a window to fully open
or close (if equipped) without holding the switch down
or up\f
To fully open the window, push the power window
switch down to the second detent and release the
switch\f To fully close the window (if equipped) , pull the
power window switch up to the second detent and
release the switch\f The switch does not have to be
held during window operation\f
To stop the window open/close operation during the
automatic function, push down or pull up the switch in
opposite directions\f Window timer (if equipped):
The window timer allows the window switch to be
operated for 15 minutes even if the ignition switch is
turned off and the key is removed\f The window timer
will be cancelled when the corresponding door is
opened or the preset time has expired\f
Auto-reverse function (if equipped):
WARNING:
There is a small distance just before the closed
position which cannot be detected. Make sure
that all passengers have their hands, etc. inside
the vehicle before closing the windows.
The auto-reverse function enables a window to
automatically reverse when something is caught in
the window as it is closing by the automatic function\f
When the control unit detects an obstacle, the window
will be lowered immediately\f
Depending on the environment or driving conditions,
the auto-reverse function may activate if an impact or
load similar to something being caught in the window
occurs\f
When power window switch does not oper-
ate
Some power window functions (automatic close
function, auto-reverse function) will not operate as
described after the battery cable is disconnected and
the electrical supply is interrupted\f Perform the
following procedure to initialize the power window
functions\f
1\f Turn the ignition switch to the "ON" position\f
2\f If the driver’s window is closed, open it completely
by operating the driver’s window switch\f
Instruments and controls2-37
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
2-38Instruments and controls
3. Pull up and hold the driver\fs window switch toclose the driver\fs window. \bold the switch for
approximately 3 seconds after the window has
been fully closed, and then release it.
4. Check if the power window functions operate properly.
If you open or close the power window continuously, it
may cause the power window not to operate properly.
Perform the above procedure.
If the power window functions do not operate properly
after performing the above procedure, repeat the
steps. See a RENAULT dealer, if necessary, for
checking the power window system.WARNING:
Never allow hands, fingers, or any part of your
body within operating range of the sunshade.
You could be injured.
CAUTION:
. Do not place any heavy objects on the roof
glass or surrounding area.
. Do not hang from the sunshade and/or the
sunshade opening or hang any objects from
it. It may cause damage or deformation to
the sunshade.
. Close the sunshade when you leave the
vehicle for extended periods of time to
prevent the inside of the vehicle from reach-
ing high temperatures.
JVI0020X
To open or close the sunshade, operate the knob*A.
To open the sunshade, slide it toward the rear of the
vehicle
*1. To close, slide the sunshade toward the
front of the vehicle*2. If the battery cable is disconnected, the clock will reset
its time and the correct time will not be indicated.
Readjust the time.
For model with the vehicle information display, see
“Vehicle information display” (P.2-20)
For the clock adjustment in the audio unit (if equipped) .
See “Audio system” (P.4-8) .
ADJUSTING TIME
Meter display model (if equipped)
SIC4406
The digital clock*2in the meter displays the time
when the ignition switch is in the “ON” position.
To display the clock, push the adjusting knob
*1. To
adjust the time, perform the following procedure.
1. Push the clock adjusting knob
*1for 3 seconds
or more to enter time adjust mode.
The hours display will start to flash.
2. Push the clock adjusting knob
*1to adjust the
hour.
To advance the time, hold down the knob
*1.
3. Wait at least 5 seconds for the minute display to flash.
SUNSHADE (if equipped) CLOCK
&RQGLWLRQ