2012 MERCEDES-BENZ G-Class Owner's Manual

i
The notches
on the guide rod must be on
the left-hand side when viewed in the
direction of travel.
X Push the head restraint down until you hear
it engage in position.
Adjusting the luxury head restraints G
WARNING
When folding back the head restraint side
bolsters, do not put your hands between the
side bolster and the cushion holder. There is
a danger of becoming trapped. X
To adjust the side bolsters of the head
restraint: push or pull right and/or left-
hand side bolster : into the desired
position.
X To adjust the angle of the head
restraint: push

or pull the head restraint in
the direction of arrow ;. Adjusting the multicontour seat
You can

adjust the contour of the front seats
individually so as to provide optimum support
for your back and sides.
X Make sure that the SmartKey is in
position 1 in the ignition lock. :
To adjust the thigh cushion
; To adjust the backrest contour in the
lumbar region
= To adjust the backrest contour in the
upper back region
? To adjust the side bolsters of the seat
backrest Adjusting the four-way lumbar
support
You can adjust the contour of the front seat
backrests individually to provide optimum
support for your back. :
To raise the backrest contour
; To soften the backrest contour
= To lower the backrest contour
? To harden the backrest contour Seats
79
Seats, steering wheel and mirrors Z

Switching the seat heating on/off
General notes The red indicator lamps in the button indicate
the heating level you have selected.
i If the battery voltage is too low, the seat
heating may switch off.
One or more of the indicator lamps in the
seat heating button are flashing.
X Make sure that the SmartKey is in position
2 in the ignition lock.
Front-seat heating i
The system automatically switches down
from level 3 to level 2 after approximately
five minutes.
The system automatically switches down
from level 2 to level 1 after approximately
ten minutes.
The system automatically switches off
approximately 20 minutes after it is set to
level 1.
X To switch on: press button : repeatedly
until the desired heating level is set.
X To switch off: press button : repeatedly
until all the indicator lamps go out. Rear-seat heating
:
Level 1 (normal heating)
; Level 2 (rapid heating)
i The system automatically switches down
from level 2 (rapid heating) to level 1
(normal heating) after approximately five
minutes.
The system automatically switches off
approximately 30 minutes after it is set to
level 1.
X To select level 1: press the upper section
of button :.
An indicator lamp lights up.
X To deactivate level 1: press the upper
section of button :.
The indicator lamp goes out.
X To select level 2: press the lower section
of button ;.
Both indicator lamps light up.
X To deactivate level 2: press the lower
section of button ;.
Both indicator lamps go out. 80
Seats
Seats, steering wheel and mirrors

Problems with the seat heating
If one or all of the indicator lamps in the seat
heating button are flashing, the seat heating
has switched off automatically. The vehicle's
electrical system voltage is too low because
too many electrical consumers are switched
on.
X
Switch off electrical consumers which you
do not need, such as the rear window
defroster or interior lighting.
Once the
battery is sufficiently charged, the
seat heating will switch back on
automatically. Switching the seat ventilation on/off
Switching on/off Seat ventilation is only available for the front
seats.
The
three

blue indicator lamps in the buttons
indicate the ventilation level you have
selected.
i If the battery voltage is too low, the seat
ventilation may switch off. X
Make sure that the SmartKey is in position
2 in the ignition lock.
X To switch on: press button : repeatedly
until the desired ventilation level is set.
i If you open the side windows and the
sliding sunroof using the SmartKey
(Y page 69), the driver's seat ventilation
automatically switches

to the highest level.X
To switch off: press button : repeatedly
until all the indicator lamps go out.
Problems with the seat ventilation If one or all of the indicator lamps in the seat
ventilation button are flashing, the seat
ventilation has switched off automatically.
The vehicle's electrical system voltage is too
low because too many electrical consumers
are switched on.
X
Switch off electrical consumers that you do
not need, such as the rear window
defroster or interior lighting.
Once the

battery is sufficiently charged, the
seat ventilation will switch back on
automatically. Steering wheel
Important safety notes
You can

adjust the steering wheel electrically. G
WARNING
Do not adjust the steering wheel while driving.
Adjusting the steering wheel while driving
could cause the driver to lose control of the
vehicle.
The electrical steering wheel adjustment
feature can be operated at any time.
Therefore, do not leave children unattended
in the vehicle, or with access to an unlocked
vehicle. A child's unsupervised access to a
vehicle could result in an accident and/or
serious personal injury.
When you adjust the steering wheel, make
sure that:
R the steering wheel can be reached with
your arms slightly bent.
R you can move your legs freely.
R you can see all the displays in the
instrument cluster clearly. Steering wheel
81
Seats, steering wheel and mirrors Z

Adjusting the steering wheel
:
To adjust the steering wheel position
(fore-and-aft adjustment)
; To adjust the steering wheel height
X Make sure that the SmartKey is in position
1 or 2 in the ignition lock.
i If the driver's door is open, the steering
wheel can

be adjusted for up to 30 minutes
after the ignition has been switched off.
X Press the lever in the direction of
arrow : or ; until the steering wheel is
in the desired position.
You can find more information under:
R EASY-ENTRY/EXIT feature (

Y page 83)
R Storing settings ( Y page 85)Steering wheel heating
Switching on/off The steering-wheel heating heats the leather
areas of the steering wheel. :
To switch on the steering-wheel heating
; Indicator lamp
= To switch off the steering-wheel heating
X To switch on/off: make sure that the
SmartKey is

in position 1 or 2 in the ignition
lock.
X Turn the lever in the direction of arrow :
or =.
Indicator lamp ; lights up or goes out.
i The steering wheel heating does not
switch off automatically.
i The steering

wheel heating may switch off
temporarily if:
R the temperature of the vehicle interior is
above 86 ‡ (30 †).
R the temperature of the steering wheel is
above 95 ‡ (35 †).
Indicator lamp ; remains on.
i The steering wheel heating is deactivated
if you remove the SmartKey from the
ignition lock. 82
Steering wheel
Seats, steering wheel and mirrors

Problems with the steering wheel
heating
If steering wheel heating indicator lamp
; is
flashing, the steering wheel heating has
switched off automatically. The vehicle's
electrical system voltage is too low because
too many electrical consumers are switched
on.
X Switch off electrical consumers which you
do not need, such as the rear window
defroster or interior lighting.
Once the
battery is sufficiently charged, the
steering wheel heating will switch back on
automatically. Steering wheel EASY-ENTRY/EXIT
feature
General notes The EASY-ENTRY/EXIT feature makes getting
in and out of your vehicle easier.
You can activate and deactivate the EASY-
ENTRY/EXIT feature in the on-board
computer (Y page 161).
Important safety notes
G
WARNING
You must make sure no one can become
trapped or injured by the moving steering
wheel when the EASY-ENTRY/EXIT feature is
activated.
To stop steering maneuver do one of the
following:
R press the steering column adjustment
switch.
R press one of the memory function position
buttons.
R press the memory button.
Do not leave children unattended in the
vehicle, or

with access to an unlocked vehicle.
Children could open the driver's door and
unintentionally activate the EASY-ENTRY/ EXIT feature. This could result in an accident
and/or serious personal injury.
G
WARNING
Let the system complete the adjustment
procedure before setting the vehicle in
motion. All steering wheel adjustment must
be completed before setting the vehicle in
motion. Driving off with the steering wheel
still adjusting could cause the driver to lose
control of the vehicle.
! Do not activate the EASY-ENTRY/EXIT
feature, if

the seat backrest is reclined too
far backwards. This can damage the front
or rear seats. You must first move the
backrest to a vertical position.
Position of the steering wheel when the
EASY-ENTRY/EXIT feature is active The steering wheel moves upwards and
towards the dashboard if:
R
you remove

the SmartKey from the ignition
lock or
R you open the driver's door with the
SmartKey in position 0 or 1 in the ignition
lock.
i The steering wheel only moves upwards
and towards the dashboard if it has not
already reached the upper end stop.
Position of the steering wheel for
driving The steering wheel is moved to the last
selected position when:
R
the driver's door is closed.
R you insert the SmartKey into the ignition
lock
The last position of the steering wheel is
stored when you switch off the ignition or
when you store the setting with the memory
function ( Y page 85). Steering wheel
83
Seats, steering wheel and mirrors Z

Mirrors
Rear-view mirror
X Adjust the rear-view mirror by hand so you
have a good overview of the traffic
conditions. Exterior mirrors
Important safety notes G
WARNING
Exercise care when using the passenger-side
exterior rear view mirror. The mirror surface
is convex (outwardly curved surface for a
wider field of view). Objects in mirror are
closer than they appear. Check your interior
rear view mirror and glance over your
shoulder before changing lanes.
At low outside temperatures, the exterior
mirrors are heated automatically.
Adjusting the exterior mirrors The switches are located on the dashboard
on the left-hand side.
X
Make sure that the SmartKey is in position
1 or 2 in the ignition lock.
X Press button ;
for
the right-hand exterior
mirror or button = for the left-hand
exterior mirror.
X Press adjustment button : up, down, to
the right or to the left until the exterior mirror is set to a position that provides you
with a good overview of traffic conditions.
You will find further information in the
"Storing settings" section (

Y page 85).
Exterior mirror out of position If an exterior mirror has been pushed out of
position, proceed as follows:
X
Move the exterior mirror into the correct
position manually.
The mirror housing is engaged again and
you can

adjust the exterior mirrors as usual
(Y page 84). Automatic anti-glare mirrors
G
WARNING
The auto-dimming function does not react if
incoming light

is not aimed directly at sensors
in the interior rear view mirror.
The interior rear view mirror and the exterior
rear view mirror on the driver's side do not
react, for example, when transporting cargo
which covers the rear window.
Light hitting the mirror(s) at certain angles
(incident light) could blind you. As a result,
you may not be able to observe traffic
conditions and could cause an accident.
The rear-view mirror and the exterior mirror
on the driver's side automatically go into anti-
glare mode if the ignition is switched on and
incident light from headlamps strikes the
sensor in the rear-view mirror.
The mirrors do not go into anti-glare mode if
reverse gear is engaged or the interior lighting
is switched on. 84
Mirrors
Seats, steering wheel and mirrors

Parking position for the exterior
mirror on the front-passenger side
General notes To make it easier to park, you can store the
front-passenger side exterior mirror position
in
such
a way that you can see the rear wheel
on that side as soon as you engage reverse
gear R.
Using the memory buttons on the driver's
side, you can store three parking positions
per key.
Setting and storing the parking position :
Adjustment button
; Right-hand exterior mirror
= Left-hand exterior mirror
? Memory button
X Make
sure that the vehicle is stationary and
that the SmartKey is in position 1 or 2 in
the ignition lock.
X Press button ; for the exterior mirror on
the front-passenger side.
X Engage reverse gear R.
The exterior mirror on the front-passenger
side moves to the preset parking position.
X Use adjustment button : to adjust the
exterior mirror to a position which allows
you to see the rear wheel and the curb.
X Press memory button ? and adjustment
button : within three seconds.
The parking

position is stored if the exterior
mirror does not move. i
If the

mirror moves out of position, repeat
the steps.
i If you shift the transmission to another
position, the exterior mirror on the front-
passenger side returns to the driving
position.
Calling up a stored parking position
setting X
With the SmartKey in position
2 in the
ignition lock

and the exterior mirror on the
front-passenger side activated, engage
reverse gear.
The exterior mirror on the front-passenger
side moves to the stored parking position.
The exterior mirror on the front-passenger
side moves back to its original position:
R as soon as you exceed a speed of
10 km/h
R about ten seconds after you have
disengaged reverse gear R
R if you press button = for the exterior
mirror on the driver's side Memory functions
Storing settings
With the memory function, you can store up
to three different settings, e.g. for three
different people.
The following settings are stored as a single
memory preset:
R position of the seat, backrest and head
restraint
R driver's side: steering wheel position
R driver's side: position of the exterior
mirrors on

the driver's and front-passenger
sides G
WARNING
Do not activate the memory function while
driving. Activating

the memory function while
driving could cause the driver to lose control
of the vehicle. Memory functions
85
Seats, steering wheel and mirrors Z

The buttons are located on the door control
panel.
X
Make sure that the SmartKey is in position
2 or that the respective door is open.
X Adjust the seat ( Y page 76) and head
restraint ( Y page 77).
X On the driver's side, adjust the steering
wheel (Y
page 82) and the exterior mirrors
(Y page 84).
X Press memory button ;.
X Press one of memory buttons :1, 2 or 3
within three seconds.
The settings are stored in the selected
storage position. Calling up a stored setting
X Press and hold the relevant memory button
1, 2 or 3, until the seat, head restraints,
steering wheel

and mirrors are in the stored
position.
i The setting procedure is interrupted as
soon as you release the memory button.
! If you

want to move the seat from the fully
reclined position to a stored seat position,
first raise the backrest using the seat
switch. The seat could otherwise be
damaged. 86
Memory functions
Seats, steering wheel and mirrors