2012 LEXUS RX350 engine

Scheduled Maintenance l og
MAINTENANCE Scheduled Maintenance Log62 132 Months or 110,000 Miles❏ Replace engine oil with 0W-20 oil; replace
oil filter
❏ Reset maintenance reminder light
❏ Rotate tires
❏ Visually inspect brake pads, calipers and rotors
❏ Check installation of driver’s floor mat
❑ Inspect wiper blades
❏ Road-test vehicle
I f you drive primarily under any of
these special operating conditions,
perform these additional items:
D
riving off-road, on dirt roads or on
dusty roads:
❏ Inspect axle shaft boots
❏ Inspect ball joints and dust covers
❏ Inspect engine air filter
❏ Inspect steering linkage and boots
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Towing a trailer, using a car-top carrier
or heavy vehicle loading:
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Driving on roads on which road salt has
been applied:
❏ Re-torque nuts and bolts of drive shaft (AWD) 138 Months or 115,000 Miles
d ate: _______ Mileage: ________ d ate: _______ Mileage: ________❏ Inspect and adjust all fluid levels
❏ Inspect engine coolant (see page 70)
❏ Reset maintenance reminder light
❏ Rotate tires
❏ Visually inspect brake pads, calipers and rotors
❏ Check installation of driver’s floor mat
❑ Inspect wiper blades
❏ Road-test vehicle
Note : If 0W-20 oil was not used at last oil
change, or if you drive primarily under certain
special operating conditions, you should also
r
eplace the engine oil with 0W-20 oil and
replace the oil filter. See page 44 for conditions
that apply. Some conditions require additional
maintenance. See belo
w.
If you drive primarily under any of
these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
❏ Inspect axle shaft boots
❏ Inspect ball joints and dust covers
❏ Inspect engine air filter
❏ Inspect steering linkage and boots
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Towing a trailer, using a car-top carrier
or heavy vehicle loading:
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Driving on roads on which road salt has
been applied:
❏ Re-torque nuts and bolts of drive shaft (AWD)

Scheduled Maintenance l og
MAINTENANCE
Scheduled Maintenance Log 63144 Months or 120,000 Miles❏ Replace engine oil with 0W-20 oil; replace oil filter
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Replace cabin air filter
❏ Replace brake fluid
❏ Replace engine air filter
❏ Replace Smart Key battery
❏ Replace spark plugs (use Denso FK20HR11 plugs
or equivalent) 1

❏ Inspect the following:
__ Axle shaft boots
__ Ball joints and dust covers
__ Body
__ Brake lines and hoses
__ Brake rotor thickness and runout
__ Drive belt
__ Exhaust pipes and mountings
__ F uel lines and connections, fuel tank band

and fuel tank vapor vent system hoses
I
f you drive primarily under any of these special operating conditions, perform
these additional items:
D riving off-road, on dirt roads or on dusty roads:
❏ Tighten nuts and bolts on chassis
Towing a trailer, using a car-top carrier or heavy vehicle loading:
❏ Replace rear differential oil (AWD)
❏ Replace transfer case oil (AWD)
❏ Replace transmission fluid
❏ Tighten nuts and bolts on chassis __ Fuel tank cap gasket
__ Rack-and-pinion assembly
__ Rear differential oil (AWD)
__ Steering linkage and boots
__ Transfer case oil (AWD)
__ Transmission for signs of leakage
__ Wiper blades❏ Reset maintenance reminder light
❏ Rotate tires
❏ Visually inspect brake pads, calipers
and rotors
❏ Check installation of driver’s floor mat
❏ Road-test vehicle
1
Required under the terms of the Emission Control Warranty.d ate: __________________________ Mileage: __________________________

Scheduled Maintenance l og
MAINTENANCE Scheduled Maintenance Log64 150 Months or 125,000 Miles 156 Months or 130,000 Miles❏ Replace engine oil with 0W-20 oil; replace
oil filter
❏ Inspect engine coolant (see page 70)
❏ Reset maintenance reminder light
❏ Rotate tires
❏ Visually inspect brake pads, calipers and rotors
❏ Check installation of driver’s floor mat
❑ Inspect wiper blades
❏ Road-test vehicle
If you drive primarily under any of
these special operating conditions,
perform these additional items:
D
riving off-road, on dirt roads or on
dusty roads:
❏ Inspect axle shaft boots
❏ Inspect ball joints and dust covers
❏ Inspect engine air filter
❏ Inspect steering linkage and boots
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Towing a trailer, using a car-top carrier
or heavy vehicle loading:
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Driving on roads on which road salt has
been applied:
❏ Re-torque nuts and bolts of drive shaft (AWD)
d ate: _______ Mileage: ________ d ate: _______ Mileage: ________❏ Inspect and adjust all fluid levels
❏ Reset maintenance reminder light
❏ Rotate tires
❏ Visually inspect brake pads, calipers and rotors
❏ Check installation of driver’s floor mat
❑ Inspect wiper blades
❏ Road-test vehicle
Note: If 0W -20 oil was not used at last oil
change, or if you drive primarily under certain
special operating conditions, you should also
r
eplace the engine oil with 0W-20 oil and
replace the oil filter. See page 44 for conditions
that apply. Some conditions require additional
maintenance. See belo
w.
If you drive primarily under any of
these special operating conditions,
perform these additional items:
D
riving off-road, on dirt roads or on
dusty roads:
❏ Inspect axle shaft boots
❏ Inspect ball joints and dust covers
❏ Inspect engine air filter
❏ Inspect steering linkage and boots
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Towing a trailer, using a car-top carrier
or heavy vehicle loading:
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Driving on roads on which road salt has
been applied:
❏ Re-torque nuts and bolts of drive shaft (AWD)

Scheduled Maintenance l og
MAINTENANCE
Scheduled Maintenance Log 65162 Months or 135,000 Miles❏ Inspect and adjust all fluid levels
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Replace Smart Key battery
❏ Reset maintenance reminder light
❏ Rotate tires
❏ Visually inspect brake pads, calipers and rotors
❏ Check installation of driver’s floor mat
❏ Road-test vehicle
❏ Inspect the following:
__ Axle shaft boots
__ Ball joints and dust covers
__ Body
__ Brake lines and hoses
__ Drive belt
__ Exhaust pipes and mountings
Note: If 0W-20 oil was not used at last oil change, or if you drive primarily under certain special operat
-
ing conditions, you should also replace the engine oil with 0W-20 oil and replace the oil filter. See page
44 for conditions that apply
. Some conditions require additional maintenance. See below.
If you drive primarily under any of these special operating conditions, perform
these additional items:
D
riving off-road, on dirt roads or on dusty roads:
❏ Inspect engine air filter
❏ Tighten nuts and bolts on chassis
Towing a trailer, using a car-top carrier or heavy vehicle loading:
❏ Replace rear differential oil (AWD)
❏ Replace transfer case oil (AWD)
❏ Tighten nuts and bolts on chassis __ Rack-and-pinion assembly
__ Rear differential oil (AWD)
__ Steering linkage and boots
__ Transfer case oil (AWD)
__ Wiper blades
d ate: __________________________ Mileage: __________________________

Scheduled Maintenance l og
MAINTENANCE Scheduled Maintenance Log66 168 Months or 140,000 Miles❏ Replace engine oil with 0W-20 oil; replace
oil filter
❏ Reset maintenance reminder light
❏ Rotate tires
❏ Visually inspect brake pads, calipers and rotors
❏ Check installation of driver’s floor mat
❑ Inspect wiper blades
❏ Road-test vehicle
I f you drive primarily under any of
these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
❏ Inspect axle shaft boots
❏ Inspect ball joints and dust covers
❏ Inspect engine air filter
❏ Inspect steering linkage and boots
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Towing a trailer, using a car-top carrier
or heavy vehicle loading:
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Driving on roads on which road salt has
been applied:
❏ Re-torque nuts and bolts of drive shaft (AWD) 174 Months or 145,000 Miles
d ate: _______ Mileage: ________ d ate: _______ Mileage: ________❏ Inspect and adjust all fluid levels
❏ Inspect engine coolant (see page 70)
❏ Reset maintenance reminder light
❏ Rotate tires
❏ Visually inspect brake pads, calipers and rotors
❏ Check installation of driver’s floor mat
❑ Inspect wiper blades
❏ Road-test vehicle
Note: If 0W-20 oil was not used at last oil
change, or if you drive primarily under certain
special operating conditions, you should also
r
eplace the engine oil with 0W-20 oil and
replace the oil filter. See page 44 for conditions
that apply. Some conditions require additional
maintenance. See belo
w.
If you drive primarily under any of
these special operating conditions,
perform these additional items:
D
riving off-road, on dirt roads or on
dusty roads:
❏ Inspect axle shaft boots
❏ Inspect ball joints and dust covers
❏ Inspect engine air filter
❏ Inspect steering linkage and boots
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Towing a trailer, using a car-top carrier
or heavy vehicle loading:
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Tighten nuts and bolts on chassis
Driving on roads on which road salt has
been applied:
❏ Re-torque nuts and bolts of drive shaft (AWD)

Scheduled Maintenance l og
MAINTENANCE
Scheduled Maintenance Log 67180 Months or 150,000 Miles❏ Replace engine oil with 0W-20 oil; replace oil filter
❏ Re-torque nuts and bolts of drive shaft (AWD)
❏ Replace cabin air filter
❏ Replace brake fluid
❏ Replace engine air filter
❏ Replace engine coolant (see page 70)
❏ Replace Smart Key battery
❏ Inspect the following:
__ Axle shaft boots
__ Ball joints and dust covers
__ Body
__ Brake lines and hoses
__ Brake rotor thickness and runout
__ Drive belt
__ Exhaust pipes and mountings
__ F uel lines and connections, fuel tank band

and fuel tank vapor vent system hoses
I
f you drive primarily under any of these special operating conditions, perform
these additional items:
D riving off-road, on dirt roads or on dusty roads:
❏ Tighten nuts and bolts on chassis
Towing a trailer, using a car-top carrier or heavy vehicle loading:
❏ Replace rear differential oil (AWD)
❏ Replace transfer case oil (AWD)
❏ Tighten nuts and bolts on chassis __ Fuel tank cap gasket
__ Rack-and-pinion assembly
__ Rear differential oil (AWD)
__ Steering linkage and boots
__ Transfer case oil (AWD)
__ Transmission for signs of leakage
__ Wiper blades❏ Reset maintenance reminder light
❏ Rotate tires
❏ Visually inspect brake pads, calipers
and r otors
❏ Check installation of driver’s floor mat
❏ Road-test vehicle
d ate: __________________________ Mileage: __________________________

e xplanation of Maintenance i te MS
MAINTENANCE
Scheduled Maintenance Log 69Cabin Air Filter
Replace at specified intervals.
More frequent replacement may
be required when driving in dusty
conditions, heavy traffic areas, urban
areas, desert areas or dirt roads.
Refer to your Owner’s Manual for
service details.
Differential Oil
Check for correct oil level and
inspect each differential component
for signs of leakage. If you discover
any leakage, have it repaired
immediately by a qualified technician.
Refer to your Owner’s Manual for
fluid specifications.
Drive Belt
Inspect for cracks, excessive wear
and oiliness. Check the belt tension
and adjust if necessary. Replace the
belts if they are damaged. Drive Shaft
Re-torque the flange nuts and bolts.
A qualified technician should perform
this operation.
Driver’s Floor Mat
• Only use the driver’s floor mat
de si gned specifically for the
model and model year of your
vehicle, such as Lexus Genuine
floor mats.
• Always properly secure the
driver’s floor mat using the
retaining hooks.
• Never install another floor mat
on top of the existing driver’s
floor mat.
• Never install the driver’s floor
mat upside down.
Engine Air Filter
Check for excessive dirt, damage and
oiliness. Replace if necessary.

e xplanation of Maintenance i te MS
MAINTENANCE Scheduled Maintenance Log70 Engine Coolant
When inspecting, visually check
the level of the engine coolant on the
see-through reservoir. Add coolant
as necessary. When replacing, drain
the cooling system and refill with
coolant. Always use Genuine Toyota
Super Long-Life Coolant or similar
high-quality non-silicate, non-amine,
non-nitrate, non-borate ethylene-
glycol coolant with long-life hybrid
organic acid technology (i.e., a
combination of low phosphates and
organic acids). A qualified technician
should perform these operations.
Check the radiator and condenser
for blockage by leaves, dirt or insects
and clean if necessary. Also check
the hose connections for corrosion
and condition of installation.
n ote: Initial replacement of engine
coolant is at 120 months/100,000
miles. Replace every 60 months/
50,000 miles thereafter. Engine Oil and Oil Filter
Replace the oil filter and drain and
refill the engine oil at specified
intervals. SAE 0W-20 oil is the best
choice for good fuel economy and
good starting in cold weather. If SAE
0W-20 is not available, SAE 5W-20
may be used; however, it must be
replaced with SAE 0W-20 at the
next oil change. See your Lexus
dealer for oil specifically formulated
for your vehicle’s engine.
Your vehicle is equipped with a
replaceable oil-filter element and oil-
filter cap O-ring; replace both at each
oil change. For instructions on how to
reset the reminder light, refer to your
Owner’s Manual.
n ote: If you do the majority of your
driving under any of the special
operating conditions indicated on
page 44, you should replace the
engine oil and oil filter every six
months or 5,000 miles, regardless
of the oil used or the certification
of the vehicle.