2012 CHEVROLET MALIBU trunk

Black plate (32,1)Chevrolet Malibu Owner Manual - 2012
10-32 Vehicle Care
Back-Up Lamps
1. Open the trunk. SeeTrunk on
page 2‑9 for more information.
2. Remove the push pins holding
the trunk trim (B).
3. Move the trim aside far enough to gain access to the bulb
assembly (A).4. Turn the bulb socket (B)counterclockwise to remove it
from the lamp assembly.
5. Pull the bulb (A) from the socket (B).
6. Install the new bulb.
7. Reverse Steps 1 through 4 to reinstall.

Black plate (40,1)Chevrolet Malibu Owner Manual - 2012
10-40 Vehicle Care
Rear Compartment Fuse
Block
The rear compartment fuse block is
located in the trunk of the vehicle.
Access the fuse block through the
trunk panel on the driver side of the
rear cargo area.
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.Fuses Usage
1 Passenger Seat
Controls
2 Driver Seat Controls
3 Not Used
4 Not Used

Black plate (41,1)Chevrolet Malibu Owner Manual - 2012
Vehicle Care 10-41
FusesUsage
5 Emission 2, Canister
Vent Solenoid
6 Park Lamps,
Instrument Panel
Dimming
7 Not Used
8 Not Used
9 Not Used
10 Sunroof Controls
11 Not Used
12 Not Used
13 Audio Amplifier
14 Heated Seat Controls
15 Not Used
16 Remote Keyless
Entry (RKE) System,
XM™
Satellite Radio
(If Equipped) Fuses
Usage
17 Back-up Lamps
18 Not Used
19 Not Used
20 Auxiliary Power
Outlets
21 Not Used
22 Trunk Release
23 Rear Defog
24 Heated Mirrors
25 Fuel Pump
Relays Usage
26 Rear Window
Defogger
27 Park Lamps
28 Not Used
29 Not Used Relays
Usage
30 Not Used
31 Not Used
32 Not Used
33 Back-up Lamps
34 Not Used
35 Not Used
36 Trunk Release
37 Fuel Pump
38 (Diode) Cargo Lamp

Black plate (73,1)Chevrolet Malibu Owner Manual - 2012
Vehicle Care 10-73
Removal and Installation of the
Sealant Canister
To remove the sealant canister:
1. Remove the plastic cover.
2. Unscrew the connector (B) fromthe canister (A). 3. Pull up on the canister (A) to
remove it.
4. Replace with a new canister which is available from your
dealer.
5. Push the new canister into place.
6. Screw the connector (B) to the canister (A).
7. Slide the plastic cover back on.
Storing the Tire Sealant
and Compressor Kit
The tire sealant and compressor kit
is located in the trunk.
1. Open the trunk. See Trunk on
page 2‑9.
2. Lift the cover.
3. Turn the retainer clockwise and remove the tire sealant and
compressor kit.
To store the tire sealant and
compressor kit, reverse the steps.

Black plate (74,1)Chevrolet Malibu Owner Manual - 2012
10-74 Vehicle Care
Tire Changing
Removing the Spare Tire
and Tools
The equipment you will need is in
the trunk.
1. Open the trunk. SeeTrunk on
page 2‑9 for more information.
2. Remove the spare tire cover.
3. Turn the wing nut counterclockwise and remove it.
Then remove the compact spare
tire. See Compact Spare Tire on
page 10‑82 for more information. 4. Remove the wing nut holding the
jack in place.
5. Remove the jack and wheel wrench from the trunk.
Tire Changing Tools
A. Wheel Wrench
B. Jack
The tools you will be using include
the wheel wrench (A) and jack (B).
1. Turn the wing nutcounterclockwise to loosen
wheel wrench.
2. Unhook the wheel wrench from the jack.

Black plate (78,1)Chevrolet Malibu Owner Manual - 2012
10-78 Vehicle Care
12. Put the wheel nuts back onwith the rounded end toward
the wheel. Tighten each nut by
hand or with the wrench until
the wheel is held against
the hub.
13. Lower the vehicle by turningthe wrench counterclockwise.
Lower the jack completely.
{WARNING
Wheel nuts that are improperly or
incorrectly tightened can cause
the wheels to become loose or
come off. The wheel nuts should
be tightened with a torque wrench
to the proper torque specification
after replacing. Follow the torque
specification supplied by the
aftermarket manufacturer when
using accessory locking wheel
nuts. See Capacities and
Specifications on page 12‑2 for
original equipment wheel nut
torque specifications.
Notice: Improperly tightened
wheel nuts can lead to brake
pulsation and rotor damage.
To avoid expensive brake repairs,
evenly tighten the wheel nuts in
the proper sequence and to the
proper torque specification.
See Capacities and Specifications
on page 12‑2 for the wheel nut
torque specification.
14. Tighten the wheel nuts firmly in a crisscross sequence, as
shown, with the wheel wrench.
Notice: Wheel covers will not fit
on the vehicle's compact spare.
If you try to put a wheel cover on
the compact spare, the cover or
the spare could be damaged.
Do not try to put a wheel cover on
the compact spare tire. It will not fit.
Store the wheel cover and wheel
nut caps in the trunk until you have
the flat tire repaired or replaced.

Black plate (79,1)Chevrolet Malibu Owner Manual - 2012
Vehicle Care 10-79
Storing a Flat Tire and Tools
{WARNING
Storing a jack, a tire, or other
equipment in the passenger
compartment of the vehicle could
cause injury. In a sudden stop or
collision, loose equipment could
strike someone. Store all these in
the proper place.
To store the flat tire and jack in the
compact spare tire compartment:
1. Open the trunk. See Trunk on
page 2‑9.
2. Remove the bolt extension (in the yellow sleeve) from the
jack and remove the center cap
from the wheel.
3. Collapse the wrench using thesame button used to extend it.
4. Attach the wrench to the jack by placing the tab on the wrench
into the hole on the side of the
jack. Then place the wrench
handle over the tab on the side
of the jack.5. Raise the jack to the heightshown and lock the wrench onto
the jack.

Black plate (81,1)Chevrolet Malibu Owner Manual - 2012
Vehicle Care 10-81
The compact spare is for temporary
use only. Replace the compact
spare tire with a full-size tire as
soon as you can. SeeCompact
Spare Tire on page 10‑82.
Storing the Spare Tire and
Tools
{WARNING
Storing a jack, a tire, or other
equipment in the passenger
compartment of the vehicle could
cause injury. In a sudden stop or
collision, loose equipment could
strike someone. Store all these in
the proper place.
1. Open the trunk. See Trunk on
page 2‑9.
2. Collapse the wrench using the same button used to extend it.
3. Attach the wrench to the jack by placing the tab on the wrench
into the hole on the side of the
jack. Then place the wrench
handle over the tab on the side
of the jack.4. Raise the jack to the heightshown and lock the wrench onto
the jack.