2011 Seat Alhambra Owner's Manual

55
Cockpit
Depending upon the equipment fitted in the vehicle, instead of a warning
lamp , sometime
s a symbol may be displayed on the instrument panel.
When certain control and warning lamps are lit, an audible warning is also
heard.
Red symbols Symbol Meaning ⇒  See
 
Do not continue driving!
The el ectr

onic parking brake is on, the brake
fluid level is too low or the brake system is faul-
ty. ⇒ page 183
 
Do not continue driving!
F au

lt in the engine cooling system. ⇒ page 283
 
Do not continue driving!
En gine oi

l pressure too low. ⇒ page 279
 
Do not continue driving!
At l

east one of the vehicles doors is open, or is
not correctly closed. ⇒ page 80
 
Do not continue driving!
The t ai

lgate is open or is incorrectly closed. ⇒ page 84
 
Do not continue driving!
F au

lt in the steering. ⇒ page 167
 Engine cannot be started again!
"AdBlue" lev
el

too low. ⇒ page 271
 Driver or passenger has not fastened seat belt. ⇒ page 21
 Use the foot brake! Change
⇒ pag
e 174
Br

ake
⇒ page 183  Faulty generator. ⇒ page 288 Yellow symbols
 Front brake pads worn.
⇒ page 183 lights: ESC (ESP) faulty or off
flashes: ESC (ESP) operating
 ASR (TCS) manually deactivated.
 ABS faulty or does not work.
 Electronic parking brake faulty. ⇒ page 183
 Rear fog light switched on. ⇒ page 95
 lights: Driving light totally or partially faulty. ⇒ page 326
flashes: Fault in the adaptive light system. ⇒ page 95
 Fault in catalytic converter.
⇒ page 228 lights: pre-ignition of diesel engine.
flashes: Fault in engine management.
 Fault in engine management.
 Diesel particulate filter blocked
 Fault in the steering system. ⇒ page 167
 Tyre pressure too low. ⇒ page 293
Fault in the tyre pressure gauge. ⇒ page 221
 Level of windscreen washer fluid too low. ⇒ page 105
 Fuel tank almost empty. ⇒ page 264
Safety First Operating instructions Practical tips Technical Data

56
Cockpit  flashes: Engine oil sensor faulty.
⇒ page 279
lights: Insufficient engine oil.
 Fault in airbag system and seat belt tensioners. ⇒ page 31

 Passenger front airbag is off (
PASSENGER AIR-
BAG  ). ⇒ page 31
 Top up "AdBlue", or there is a fault in the "AdBl-
ue" system.
⇒ page 271
 Fuel tank not closed correctly. ⇒ page 264
 Lane Assist is connected, but not active. ⇒ page 216
Green symbols
Symbol Meaning ⇒  See

 Left or right turn signal. ⇒ page 95
Hazard warning lights on. ⇒ page 312
 Use the foot brake! Change
⇒ page 174
Br ak
e
⇒ page 183  Cruise control operating. ⇒ page 212
 Lane Assist is connected and active. ⇒ page 216 Blue symbols
Symbol Meaning
⇒  See
 Headlight on or flasher on.
⇒ 
page 95  Headlight adjustment (Light Assist) on.
Colourless symbols
Symbol Meaning ⇒  See
 Electronic immobiliser active. ⇒ page 170
 Service interval display ⇒ page 61
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
● Never ignore the warning lamps or text messages.
● Stop the vehicle safely as soon as possible.
● Park the vehicle away from the traffic, ensuring that there are no easi-
ly inflammable materials under the vehicle which could come into contact
with the exhaust system (e.g. dry grass, fuel).
● A faulty vehicle represents a risk of accident for the driver and for oth-
er road users. If necessary, switch on the hazard warning lamps and put
out the warning triangle to advise other drivers.
● Before opening the bonnet, switch off the engine and allow it to cool.
● In any vehicle, the engine compartment is a hazardous area and could
cause severe injury ⇒ page 275. CAUTION
Failure to heed the warning lamps and text messages when they appear
may result in faults in the vehicle. 

57
Cockpit
Instruments Introduction Additional information and warnings:
●
Indicator lamps ⇒ pag e 54
● Gear engaged display (automatic gearbox) ⇒ pag
e 174.
● Instructions for inspection intervals ⇒ Booklet
Maintenance Programme WARNING
Any distraction may lead to an accident, with the risk of injury.
● Do not handle the instrument panel controls when driving. 
View of instrument panel Fig. 35 Instrument panel, on dash panel.
Details of the instruments ⇒ fig. 35: 1)
Depending on the vehicle equipment, it is also possible to set the time using the settings
menu on the in
strument panel display ⇒ page 67.Safety First Operating instructions Practical tips Technical Data

58
Cockpit
Clock set button 1)
.
– Pre s
s button  to select the hour or minute display.
– To c ontinue settin

g the time, press button 0.0 / SET
7 . Hold button
down t o s

croll through the numbers quickly.
– Press button  again to end the clock setting.
Rev c

ounter (with the engine running, in thousands of revolutions per
minute).
The beginning of the red zone of the rev counter indicates the maxi-
mum speed in any gear after running-in and with the engine hot. How-
ever, it is advisable to change up a gear or move the selector lever to D
(or lift your foot off the accelerator) before the needle reaches the red
zone ⇒  .
Engine c oo

lant temperature display  ⇒ page 283.
Displays on the screen ⇒ page 58.
Fuel reserve display ⇒ page 264.
Speedometer.
Reset knob for trip recorder (trip).
– Press button 0.0 / SET to reset to zero.
CAUTION
To prevent damage to the engine, the rev counter needle should only re-
main in the r ed

zone for a short period of time. For the sake of the environment
Changing up a gear in time reduces fuel consumption and noise. 
Displays on screen A variety of information can be viewed on the instrument panel display
⇒ 
fig. 35 4 , depending on the vehicle equipment:
1
2
3
4
5
6
7 ●
Warning and information texts
● Mil

eage
● Time
● Ambient temperature
● Compass
● Selector lever positions ⇒ page 174
● R

ecommended gear (manual gearbox) ⇒ page 174
● M

ultifunction display (MFI) and menus for different setting options
⇒ page 62
● Ser

vice interval display ⇒ page 61
● Sec

ond speed display (menu Configuration
) ⇒ page 62
● Start/Stop operation indicator ⇒ pag
e 59
Warning and information texts
The system runs a check on certain components and functions when the ig-
nition is switched on and while the vehicle is moving. Faults in the opera-
tion are displayed on the screen using red and yellow symbols and messag-
es on the instrument panel display ( ⇒ page 54) and, in some cases, with
audible warnings. The display may vary according to the type of instrument
panel fitted. 

59
Cockpit Type of mes-
sag
e Symbol
co lour Meanings
Priority 1
warnin
g. Red Symbol flashing or lit; partly combined with
audibl
e w
arnings.
 Stop the vehicle! It is dangerous ⇒  !
Check the f

unction which is faulty and repair.
If necessary, request assistance from special-
ised personnel. Priority 2
warnin
g. Yellow Symbol flashing or lit; partly combined with
audibl
e w

arnings.
A faulty function, or fluids which are below
the correct levels may cause damage to the
vehicle! ⇒  Check the faulty function as soon as possible.
If nec
e

ssary, request assistance from special-
ised personnel. Informative
te
xt

. – Information relating to different vehicle pro-
ce
s
ses. Mileage
The odometer
r

egisters the total distance travelled by the car.
The trip recorder (trip) shows the distance travelled since the last trip re- corder reset. The last digit of the trip recorder indicates distances of 100
metres or tenths of a mile.
Outside temperature display
When the outside temperature is below +4°C (+39°F), the symbol “ice crys-
tal” (warning of risk of freezing) is also displayed next to the temperature.
At first this symbol flashes and then it remains lit until the outside tempera-
ture rises above +6°C (+43°F) ⇒  .
When the v ehic

le is at a standstill, with the auxiliary heating on
(⇒ page 163), or when travelling at very low speeds, the temperature dis-
played may be higher than the true outside temperature, as a result of the
heat produced by the engine. The temperatures measured range from -40°C to +50°C (-40°F to +122°F).
Compa

ss
With the ignition on and the navigation system on, the cardinal point corre-
sponding to the vehicle's direction of travel is displayed on the instrument
panel ⇒ page 60.
Selector lever positions
The range of engaged gears of the selector lever is shown on the side of the
lever, and on the instrument panel display. In positions D and S, and with
the Tiptronic, the corresponding gear is also displayed.
Recommended gear (manual gearbox)
The recommended gear to save fuel is displayed on the instrument panel
while you are driving ⇒ page 174.
Second speed display (mph or km/h)
In addition to the speedometer, the speed can also be displayed in a differ-
ent unit of measurement (in miles or in km per hour). To change the units, in
the Settings menu, select the option Second speed ⇒ page 62.
Vehicles without menu display on the instrument panel
● Switch on the engine.
● Press button  three times. The odometer display flashes on the instru-
ment p anel

display.
● Press button 0.0 / SET once. “mph” or “km/h” is displayed briefly in-
st e

ad of the odometer.
● This activates the second speed display. To switch it off, repeat the pro-
cedure.
Thi

s option cannot be disconnected in models destined for countries in
which the second speed must always be visible.
Start/Stop operating display
Updated information relating to the status is displayed on the instrument
panel ⇒ page 194. Safety First Operating instructions Practical tips Technical Data

60
Cockpit WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or m a
y cause accidents and severe injuries.
● Never ignore the warning lamps or text messages.
● Stop the vehicle safely as soon as possible.
● A faulty vehicle represents a risk of accident for the driver and for oth-
er roa
d users. If necessary, switch on the hazard warning lamps and put
out the warning triangle to advise other drivers.
● Park the vehicle away from the traffic, ensuring that there are no easi-
ly inflamm
able materials under the vehicle which could come into contact
with the exhaust system (e.g. dry grass, fuel). WARNING
Although the outside temperature is above freezing, some roads and
bridge s

may be frozen.
● At an outside temperature of above +4°C (+39°F), even when the “ice
cry

stal” is not visible, there may still be ice on the road.
● Never rely totally on the outside temperature display! CAUTION
Failure to heed the warning lamps and text messages when they appear
ma y

result in faults in the vehicle. Note
● Different versions of the instrument panel are available and therefore
the v

ersions and instructions on the display may vary. In the case of dis-
plays without warning or information texts, faults are indicated exclusively
by the warning lamps.
● When several warnings are active at the same time, the symbols are
shown suc
cessively for a few seconds. The symbols will stay on until the
fault is rectified. Compass*
Fig. 36 Magnetic zones.
The comp a

ss does not require calibration in vehicles for which the naviga-
tion system was mounted at the factory. The option compass disappears.
The compass in vehicles in which the navigation system was not mounted
at the factory, is permanently and automatically calibrated. If electronic or
metal accessories (mobile phone, television) are subsequently mounted in
the vehicle, the compass should be recalibrated manually.
Adjusting the magnetic zone
● Switch the ignition on.
● Select the Settings
menu followed by the option Compass and Zone.
● Select the magnetic zone corresponding to the position of the vehicle
⇒  fig. 36.
● Adjust and confirm the magnetic zone ( 1-15).

61
Cockpit
Calibrating compass
To c alibr
ate the compass you must be in one of the valid magnetic zones
with sufficient space to be able to trace a circumference with the vehicle.
● Switch the ignition on.
● Select the Settings
menu followed by the option Compass and Calibrate.
● Confirm the message Des
cribe a complete circumference to calibrate the
compass with OK and then trace a complete circumference driving at ap-
pro x
imately 10 km/h (6 mph).
When the corresponding cardinal point is displayed, the calibration is com-
plete. 
Service interval display The inspection display appears on the instrument panel
⇒ fig. 35 4 .
SEA T m

akes a difference between services with engine oil change (Mainte-
nance Service) and services without engine oil change (Inspection Service).
The service interval display only gives information for service dates which
involve an engine oil change. The dates of the remaining services (for exam-
ple, the next Inspection Service or change of brake fluid) are listed on the
label attached to the door strut, or even in the Maintenance Programme.
In vehicles with Services established by time or mileage , the service inter-
vals are already pre-defined.
In vehicles with LongLife Service , the intervals are determined individually.
Technical progress has made it possible to considerably reduce servicing re-
quirements. The technology used by SEAT ensures that your vehicle only
has an maintenance service when it is necessary. To establish when the
Maintenance Service is due (max. 2 years), the vehicle's conditions of use
and individual driving styles are considered. The service pre-warning first
appears 20 days before the date established for the corresponding service.
The kilometres remaining until the next service are always rounded up to the nearest 100 km and the remaining time is given in complete days. The
current

service message cannot be viewed until 500 km after the last serv-
ice. Prior to this only lines are visible on the display.
Inspection reminder
When the Service date is approaching, when the ignition is switched on a
Service reminder is displayed.
In vehicles without text messages , a spanner is displayed on the instrument
panel  with a figure given in km. The number of kilometres shown is the
maximum number that may be driven until the next service. After a few sec-
onds,the display mode changes. A clock symbol appears and the number of
days until the next service appointment is due.
In vehicles with text messages , Service in --- km or --- days is displayed on
the instrument panel.
Service due
After the service date, an audible warning is given when the ignition is
switched on and the spanner displayed on the screen flashes for a few sec-
onds. In vehicles with text messages , Service in --- km or --- days is dis-
played on the instrument panel.
Reading a service notification
With the ignition switched on, the engine off and the vehicle at a standstill,
the current service notification can be read:
● Press the button  on the instrument panel several times until the
sp anner symbo

l is displayed .
● ALTERNATIVELY: select the Settin
gs menu.
● From the Servic
e submenu, select the option Info.
When the service date has past , a minus sign is displayed in front of the
number of kilometres or days. In vehicles with text messages the following
is displayed: Service --- km or --- days ago . Safety First Operating instructions Practical tips Technical Data

62
Cockpit
The service interval display is reset
If the ser v
ice was not carried out by a Technical Service, the display can be
reset as follows: In vehicles with text messages:
Select the
Settings
menu.In the submenu Serv
ic
e, select the option Reset.Confirm with
OK when requested to do so by the system.
In vehicles without text messages:
Switch the ignition off.
Press and hold the
0.0 / S
ET button.
Switch the ignition back on.
Release the
0.0 / S
ET button and, press
 for the next 20 seconds.
Do not reset the indicator to zero between two intervals, otherwise the dis-
p l

ay will be incorrect.
If, while the LongLife service is valid, the service interval display is reset to
zero, the “service will be activated by time or mileage”. The service interval
is no longer calculated individually ⇒ Booklet Maintenance Programme.Note
● The service message disappears after a few seconds, when the engine is
s t

arted or when OK is pressed.
● In vehicles with the LongLife system in which the battery has been dis-
connect ed f

or a long period of time, it is not possible to calculate the date
of the next service. Therefore the service interval display may not be correct.
In this case, please check the maximum permitted service intervals ⇒ Book-
let Maintenance Programme. SEAT information system
Introduction With the ignition switched on, it is possible to read the different functions of
the dis
p

lay by scrolling through the menus.
In vehicles with a multifunction steering wheel, there are no buttons on the
windscreen wiper lever. The multifunction display can only be controlled
from the buttons on the multifunction steering wheel.
The number of menus displayed on the instrument panel will vary according
to the vehicle electronics and equipment.
A specialised dealer will be able to programme or modify additional func-
tions, according to the vehicle equipment. SEAT recommends visiting a
Technical Service.
Some menu options can only be read when the vehicle is at a standstill.
As long as a priority 1 warning is displayed, it will not be possible to read
the menus. To display the menus, confirm the warning by pressing OK .
Addition a

l information and warnings:
● Exterior mirrors ⇒ pag
e 110
● Auxiliary heating ⇒ pag
e 163 WARNING
Any distraction may lead to an accident, with the risk of injury.
● Do not read the instrument panel menus when driving. 