2011 RENAULT SCENIC Engine And Peripherals Workshop Manual

13B-137
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET703 CRUISE CONTROL/SPEED LIMITER BUTTONS
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system programming
functions.
INACTIVEStatus ET703 becomes INACTIVE when none of the cruise control - speed limiter
buttons are pressed. These buttons are located on the steering wheel.
To remove the driver's airbag to perform the checks in complete safety.
(see 88C, Airbag and pretensioners)
If status ET703 does not display INACTIVE,
• check the condition of the cruise control/speed limiter +/- button and the condition
of its connector.
• check the condition of the cruise control/speed limiter R/0 button and the condition
of its connector.
Repair if necessary.
DDCR_V44_ET703/DDCR_V48_ET703

13B-138
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET703
CONTINUED 1
INCREASE
Status ET703 becomes PLUS when the cruise control / speed limiter + button is
pressed. This button is on the steering wheel, on the left-hand side.
To remove the driver's airbag to perform the checks in complete safety.
(see 88C, Airbag and pretensioners)
If status ET703 does not display INCREASE, check the condition of the cruise control
- speed limiter +/- button and the condition of its connector. Repair if necessary.
Measure the resistance on the following connections while pressing
the + button (on the button tracks):
• Connection code 86G of component 331.
• Connection code 86M of component 331.
If the resistance is not approximately 300 Ωcheck the continuity of the connection
when the button is not pressed. If there is continuity, replace the +/- control button.
(see MR 364 (Mégane II), MR 370 (Scénic II), Mechanical, 83D, Cruise control,
Steering wheel switch: Removal - Refitting).
DECREASEStatus ET703 becomes DECREASE when the - button of the cruise control/speed
limiter is pressed. This button is on the steering wheel, on the left-hand side.
To remove the driver's airbag to perform the checks in complete safety.
(see 88C, Airbag and pretensioners)
If status ET703 does not change to MINUS, check the condition of the cruise control
/ speed limiter +/- button, and the condition of its connector. Repair if necessary.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of the following connections while pressing the "-"
button (on the button tracks):
• Connection code 86G of component 331.
• Connection code 86M of component 331.
If the resistance is not approximately 100 Ωcheck the continuity of the connection
when the button is not pressed. If there is continuity, replace the +/- control button.
(see MR 364 (Mégane II), MR 370 (Scénic II), Mechanical, 83D, Cruise control,
Steering wheel switch: Removal - Refitting).

13B-139
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET703
CONTINUED 2
SUSPEND
Status ET703 becomes SUSPEND when the cruise control / speed limiter 0 button is
pressed. This button is located on the steering wheel, to the right.
To remove the driver's airbag to perform the checks in complete safety.
(see 88C, Airbag and pretensioners)
If status ET703 does not become SUSPEND, check the condition of the cruise control
- speed limiter R/0 button and the condition of its connector.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of the following connection whilst pressing the 0 button
(on the button tracks):
• Connection code 86G of component 331.
• Connection code 86M of component 331.
If the resistance is not approximately 0 Ω, replace the R/0 control button.
If there is continuity, replace the R/0 control button (see MR 364 (Mégane II), MR 370
(Scénic II), Mechanical, 83D, Cruise control, Steering wheel switch: Removal -
Refitting).

13B-140
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET703
CONTINUED 3
RESUME
Status ET703 becomes RESUME when the R button of the cruise control/speed
limiter is pressed. This button is located on the steering wheel, to the right.
To remove the driver's airbag to perform the checks in complete safety.
(see 88C, Airbag and pretensioners)
If status ET703 does not change to RESUME, check the condition of the cruise
control / speed limiter R/0 button, and the condition of its connector. Repair if
necessary.
If there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Measure the resistance on the following connection while pressing
the R button (on the button tracks):
• Connection code 86G of component 331.
• Connection code 86M of component 331.
If the resistance is not approximately 900 Ω, check the continuity of the connection
when the button is not pressed. If there is continuity, replace the R/0 control button
(see MR 364 (Mégane II), MR 370 (Scénic II), Mechanical, 83D, Cruise control,
Steering wheel switch: Removal - Refitting).

13B-141
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET704
ET705BRAKE SWITCH NO. 1
BRAKE SWITCH NO. 2
NOTESNone.
Note:
Statuses ET704 and ET705 should change status at the same time. In the event of inconsistency, refer to
the interpretation of fault DF050 Brake switch circuit.
DDCR_V44_ET704/DDCR_V48_ET704 / DDCR_V44_ET705/DDCR_V48_ET705

13B-142
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET704
ET705
CONTINUED
ACTIVE
OR
INACTIVE
If the brake lights are working:
check the continuity and the absence of interference resistance on the following
connection:
– connection code 5A between components 160 and 120, 645, 119.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the brake lights are not operational, check:
– the condition and fitting of the brake switch,
– the condition and conformity of the brake light fuse,
– the conformity of the values in the following table:
disconnect the switch and carry out the following checks:
for MEGANE II and SCENIC II with ESP
Continuity between
connectionsInsulation between
connections
Switch engaged
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal depressed)65G and SP17 5A and BPT
For MEGANE II and SCENIC II without ESP
Continuity between
connectionsInsulation between
connections
Switch engaged
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal depressed)65G and SP17 5A and BPT
Replace the switch if the values obtained are not correct.

13B-143V4 MR-372-J84-13B000$100.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
* Heat.: HeatingTool parameter DIAGNOSTIC TOOL DESCRIPTION
PR005 EGR valve opening setpoint
PR008 Rail pressure set point
PR009 Turbocharging pressure setpoint
PR010 Idle speed regulation setpoint
PR017 Fuel flow
PR073 Air flowmeter supply voltage
PR028 Pedal position (gang 1)
PR029 Pedal position (gang 2)
PR030 Accelerator pedal position
PR032 Inlet pressure
PR035 Atmospheric pressure
PR037 Refrigerant pressure
PR038 Rail pressure
PR051 EGR valve position feedbac
PR055 Engine speed
PR059 Inlet air temperature (invalid in K9K 728)
PR061 External air temperature
PR063 Fuel temperature
PR064 Coolant temperature
PR074 Battery voltage
PR077 EGR valve position sensor voltage
PR080 Rail pressure sensor voltage
PR081 Inlet temperature sensor voltage
PR088 Pedal potentiometer gang 2 voltage
PR089 Vehicle speed
PR125 Power absorbed by air conditioning compressor
PR127 Heat.* resistor maximum authorised power
PR130 Cruise control setpoint
PR132 Air flow
DIESEL INJECTION
Fault finding – Parameter summary table

13B-144V4 MR-372-J84-13B000$110.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
PR059 INLET AIR TEMPERATURE
NOTESSpecial notes:
This parameter is invalid and set at -50°C for K9K 728 engines.
Check the condition of the air temperature - pressure sensor connections.
If necessary replace the sensor.
Measure the resistance between tracks 1 and 2 of the air temperature - pressure sensor.
Theoretical values:
8950 to 9901 Ω at -10°C
7054 to 7784 Ω at -5°C
5605 to 6169 Ω at 0°C
3618 to 3964 Ω at 10°C
2400 to 2620 Ω at 20°C
1645 to 1787 Ω at 30°C
Replace the air temperature - pressure sensor if it is not in order.
DDCR_V44_PR059/DDCR_V48_PR059
DIESEL INJECTION
Fault finding – Interpretation of parameters
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.