2011 RENAULT SCENIC cruise control

13B-306V9 MR-372-J84-13B450$152.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR130CRUISE CONTROL SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the cruise control setpoint.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults must be present.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– or after a customer complaint (lack of power, smoke etc.).
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
Indicates the cruise control cruising speed.
Cruise control can only be activated for a speed.
V > 18 mph (30 km/h)
EDC16C36_V44_PR130/EDC16C36_V4C_PR130/EDC16C36_V48_PR130/EDC16C36_V50_PR130/EDC16C36_V54_PR130/
EDC16C36_V58_PR130
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-350V9 MR-372-J84-13B450$160.mif
13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Tool
commandDiagnostic tool title comments
SC001Write saved data See Interpretation of commands.
SC002Enter injector codes See Interpretation of commands.
SC003Save computer data See Interpretation of commands.
SC017Particle filter regeneration See Interpretation of commands.
SC031Operational fault finding of cylinders See Interpretation of commands.
SC035High pressure fuel circuit fault finding See Interpretation of commands.
SC036Reinitialise programming See Interpretation of commands.
RZ001Fault memory See Interpretation of commands.
RZ005Programming See Interpretation of commands.
RZ034Computer memory See Interpretation of commands.
LC009Air conditioning See configuration and programming.
LC056Heating elements See configuration and programming.
LC065Water in diesel fuel sensor See configuration and programming.
LC120Cruise control See configuration and programming.
LC121Speed limiter See configuration and programming.
AC004Turbocharging solenoid valve See Interpretation of commands.
AC011Rail pressure regulator See Interpretation of commands.
AC012Damper valve See Interpretation of commands.
AC037Preheating relay See Interpretation of commands.
AC038Low speed GMV relay See Interpretation of commands.
AC039High speed GMV relay See Interpretation of commands.
AC103EGR by-pass See Interpretation of commands.
AC231Richness ratio sensor heating See Interpretation of commands.
VP010Write VIN See Interpretation of commands.
VP036Fuel supply inhibited See
Interpretation of commands.
VP037Lift fuel supply inhibition See Interpretation of commands.
DIESEL INJECTION
Fault finding – Command summary table

13B-365
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
RZ005PROGRAMMING
NOTESThis command enables you to reinitialise the entire computer configuration according
to the vehicle.
Ignition on and engine stopped.
Command RZ005 reconfigures the computer.
if the computer has no configuration data,
run command RZ005 to enter the options fitted on the vehicle:
– air conditioning,
– cruise control/speed limiter.
These options are detected by the computer even if command RZ005 is not used.
the computer is configured as soon as the one of the vehicle's optional system components is operated.
EDC16C36_V44_RZ005/EDC16C36_V4C_RZ005/EDC16C36_V48_RZ005/EDC16C36_V50_RZ005/EDC16C36_V54_RZ005/
EDC16C36_V58_RZ005EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58