2011 RENAULT SCENIC cruise control

13B-221V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 4
SPEED LIMITER
MEGANE II:
When the driver presses the main speed limiter switch, status ET042 becomes
SPEED LIMITER.
If CRUISE CONTROL or INACTIVE appears although the switch was pressed in the
speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition on the switch connector.
– Connection code AP43 of component 1081.
Disconnect the main switch, and when it is in the rest position, check the insulation
between:
– Connection codes AP43 and 3FX of component 1081.
– Connection codes AP43 and 3PD of component 1081.
Check the continuity between connections AP43 and 3PD of component 1081 in
the speed limiter position.
Check the continuity between connections AP43 and 3FX of component 1081 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the continuity, insulation and the absence of interference resistance on
the following connections:
– Connection code 3FX,
– Connection code 3PD,
between components 1081 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-222V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 5
SPEED LIMITER
SCENIC II:
When the driver presses the main speed limiter switch, status ET042 becomes
SPEED LIMITER.
If CRUISE CONTROL or INACTIVE appears although the switch was pressed in the
speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition on the switch connector.
– Connection code AP43 of component 1546.
Disconnect the main switch, and when it is in the rest position, check the insulation
between:
– Connection codes AP43 and 3FX of component 1546.
– Connection codes AP43 and 3PD of component 1546.
Check the continuity between connections AP43 and 3PD of component 1546 in
the speed limiter position.
Check the continuity between connections AP43 and 3FX of component 1546 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the continuity, insulation and the absence of interference resistance on
the following connections:
– Connection code 3FX,
– Connection code 3PD,
between components 1546 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-223V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 6
CRUISE
CONTROL
MEGANE II:
When the driver presses the main cruise control button, status ET042 becomes
CRUISE CONTROL.
If SPEED LIMITER or INACTIVE appears although the driver pressed the switch in
the cruise control position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition on the switch connector.
– Connection code AP43 of component 1081.
Disconnect the main switch, and when it is in the rest position, check the insulation
between:
– Connection codes AP43 and 3FX, of component 1081.
– Connection codes AP43 and 3PD of component 1081.
Check the continuity between connections AP43 and 3PD of component 1081 in
the speed limiter position.
Check the continuity between connections AP43 and 3FX of component 1081 in
the cruise control position.
If these checks show incorrect values, replace the switch.
Check the continuity, insulation and the absence of interference resistance on
the following connections:
– Connection code 3FX,
– Connection code 3PD,
between components 1081 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-224V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 7
CRUISE
CONTROL
SCENIC II:
When the driver presses the main cruise control button, status ET042 becomes
CRUISE CONTROL.
If SPEED LIMITER or INACTIVE appears although the driver pressed the switch in
the cruise control position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
After ignition, check for +12 V on the switch connector.
– Connection code AP43 of component 1546.
Disconnect the main switch, and when it is in the rest position, check the insulation
between:
– Connection codes AP43 and 3FX of component 1546.
– Connection codes AP43 and 3PD of component 1546.
Check the continuity between connections AP43 and 3PD of component 1546 in
the speed limiter position.
Check the continuity between connections AP43 and 3FX of component 1546 in
the cruise control position.
If these checks show incorrect values, replace the switch.
Check the continuity, insulation and the absence of interference resistance on
the following connections:
– Connection code 3FX,
– Connection code 3PD,
Between components 1546 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-240V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415CRUISE CONTROL/SPEED LIMITER DEACTIVATION
STATUS DEFINITIONThis status varies according to engine specifications.
NOTESSpecial notes:
Apply the conformity check to see if the statuses are inconsistent with the operating
programs of the system.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
STATUS 1Traction control request.
STATUS 2Brake pedal depressed.
STATUS 3Clutch pedal depressed.
STATUS 4Suspend button pressed.
STATUS 5Cruise control or speed limiter monitoring.
STATUS 6Inconsistency between the request and the vehicle speed. Gear lever in neutral
(manual gearbox) or the neutral position (automatic gearbox).
EDC16C36_V44_ET415/EDC16C36_V4C_ET415/EDC16C36_V48_ET415/EDC16C36_V50_ET415/EDC16C36_V54_ET415/
EDC16C36_V58_ET415
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-241V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 1
STATUS 7
Inconsistency between the request and the vehicle speed.
STATUS 8Automatic transmission in defect mode.
STATUS 9Vehicle speed monitoring.
STATUS 10Monitoring by the injection computer.
Sensor electrical conformity
Note:
Cruise control can be activated when the vehicle speed exceeds 18 mph (30 km/h).
Status ET415 displays the various reasons for deactivation of the cruise control/speed limiter function, due to a
driver request or the external environment (e.g. STATUS 1).
IMPORTANT
Clear the fault memory by running command RZ001 Fault memory to reset this status to NONE.
WITHOUT
This status is present on the diagnostic tool if:
the computer has been reinitialised,
the computer has been reprogrammed.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-242V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 2
STATUS 1
Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving with the cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and traction control is
requested.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 1 with no traction control request (see 38C, Anti-
lock Braking System).
STATUS 2Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2, when driving, with cruise control active (ET042
Cruise control/Speed limiter: CRUISE CONTROL) and the brake pedal depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult the
interpretation of statuses ET704 and ET705 Brake switch No. 1 and No. 2.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-243V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 3
STATUS 3
Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is no longer coupled to
the engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active
(ET042 Cruise control/speed limiter: CRUISE CONTROL) and the clutch pedal is
depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed,
consult the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with an automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation
to the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, Multiplexing).
STATUS 4Cancel button pressed
The cruise control/speed limiter function is deactivated whenever the suspend button
is pressed.
Status ET415 becomes STATUS 4, when driving when:
– Either the cruise control is active, or
– the speed limiter is active
– and when the "0" button is pressed by the driver.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703 Cruise control/speed limiter buttons and run fault-
finding on the R/0 control button located on the steering wheel, to the right.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58