13B-11V9 MR-372-J84-13B450$030.mif
DIESEL INJECTION
Fault finding – List and location of components13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Refrigerant pressure sensor:
This sensor is located on the coolant circuit.
Engine coolant temperature sensor:
This sensor is located on the cylinder head near the engine water chamber.
Air temperature sensor:
The air temperature sensor is located at the air circuit inlet, integrated into the air flowmeter.
Turbocharging pressure sensor solenoid valve:
This solenoid valve is located on the turbocharger.
Catalytic converter:
The catalytic converter is located downstream of the turbocharger.
Fuel temperature sensor:
This sensor is located near the injection pump and injector return.
Cruise control/speed limiter on/off switch:
This switch is located in the passenger compartment to the left of the steering wheel near the lighting dimmer.
Fan unit relay:
The relay is located on the cooling radiator.
Accelerator potentiometer:
The potentiometer is located on the accelerator pedal.
Clutch pedal switch:
The switch is located on the clutch pedal.
Heater plugs:
The heater plugs are located on the cylinder head.
The richness ratio sensor:
The richness ratio sensor is mounted in the turbo outlet.
The turbocharger cooling pump:
This pump is located next to the turbocharger.
Particle filter downstream temperature sensor:
The sensor is located after the particle filter (only on certain F9Q816 engines in Vdiag 48).
Particle filter upstream temperature sensor:
The sensor is located before the particle filter (only on engine type F9Q816).
Particle filter differential pressure sensor:
The sensor is located on the particle filter (only on engine type F9Q816).
13B-13V9 MR-372-J84-13B450$040.mif
DIESEL INJECTION
Fault finding – Role of components13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Particle filter:
The particle filter retains the particles for destruction during regeneration, preventing these particles from being
discharged into the atmosphere (engine type F9Q816 only).
TDC sensor:
The angular position is measured using a magneto-inductive sensor triggered by the machined teeth on the engine
flywheel. This sensor gives the engine speed as well as the position of the crankshaft for injection.
Camshaft sensor:
This sensor provides a signal to perform the injection cycle.
When the piston for cylinder 1 is at top dead centre (TDC), it may be either at the end of the compression stroke or
at the end of the exhaust stroke. The camshaft sensor makes the distinction between these two states.
Electric coolant pump:
The electric water pump is activated if the coolant temperature has reached a significant temperature threshold
when the engine has stopped.
Role: to cool the turbocharger when the engine is stopped.
Refrigerant pressure sensor:
Its role is to measure the refrigerant pressure in the air conditioning circuit.
Heating elements:
The heating elements heat the engine coolant to improve user comfort (only on certain types of F9Q816 engine
in Vdiag 48).
Engine coolant temperature sensor:
The engine coolant temperature sensor informs the computer of the engine coolant temperature.
Air temperature sensor:
The air temperature sensor is fitted inside the inlet manifold and informs the computer of the temperature of the air
taken in by the engine.
Turbocharging pressure sensor solenoid valve:
This solenoid valve operates the turbocharger wastegate pneumatic circuit to lower the turbocharging pressure.
Catalytic converter:
The role of the catalytic converter is to convert pollutant gases into harmless gases.
Fan unit relay:
This relay controls the activation of the engine cooling fan assembly when a temperature threshold has been
exceeded.
Accelerator potentiometer:
The accelerator potentiometer informs the computer of the position of the accelerator pedal (engine load).
