2011 RENAULT SCENIC fuel

13B-362
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC035
CONTINUED
Explanation of results interpretation:
Check 1:
– Use scenario SC031: Operational fault finding of cylinders.
–For VDiag 44, run Test 10 Poor injector operation.
–Apply ALP6 Fuel circuit external leaks.
–Run Test 3 Low pressure circuit check.
– Replace the high pressure pump.
Check 2:
– Use scenario SC031: Operational fault finding of cylinders.
–For VDiag 44, run Test 10 Poor injector operation.
–Apply ALP6 Fuel circuit external leaks.
– Run the part of Test 3 Low pressure circuit check which concerns the fuel filter.
– Replace the high pressure pump.
– Check the injector return flow and the injectors, run Test 10 Poor injector operation.
– Check the rail pressure regulator by running command AC011 “Rail pressure regulator”.
Check 3:
– Use scenario SC031: Operational fault finding of cylinders.
–For VDiag 44, run Test 10 Poor injector operation.
–Apply ALP6 Fuel circuit external leaks.
–Run Test 3 Low pressure circuit check.
– Replace the high pressure pump.
Check 4:
Replace the high pressure pump.
Check 5:
– Check the injector return flow and the injectors (run Test 10 Poor injector operation).
– Check the rail pressure regulator by running command AC011 “Rail pressure regulator”.
Consult the repair manual for the various checks (from 1 to 5), see MR 364 (Mégane II ph2), MR 370 (Scénic II
ph2), Mechanical, 13B, Diesel injection, Injector rail, Removal - Refitting.
Repair if necessary.
EDC16 C36
Program No.: 91
Vdiag No.: 4C, 48, 50,
54, 58

13B-370
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC011
CONTINUED
Step 2
In the event of rail overpressure:
Check that there are no air bubbles in the diesel fuel low pressure circuit.
Check that the rail pressure sensor is operating correctly.
Consult the interpretation of parameter PR038 Rail pressure.
If these checks reveal no irregularities, replace the regulator.
in the event of rail underpressure:
Check that the rail pressure sensor is operating correctly.
Consult the interpretation of parameter PR038 Rail pressure.
Check the low pressure diesel circuit priming.
Check the conformity of the diesel filter connections.
Check the condition of the filter (clogging and water saturation).
Check that there are no air bubbles between the filter and the high pressure pump.
Check the sealing of the low and high pressure diesel fuel systems: use ALP6 Fuel circuit leaks (visual
inspections, touch tests, odours, etc.) on:
pump body, pressure release valve, pipes, rail and injectors unions, injector wells, etc.
Check the conformity of the seal fitting on the pressure regulator.
Check the operation of the injectors, run Test 10 Poor injector operation.
Carry out the necessary repairs.
If the engine starts:
Clear any faults.
Check the pressure regulator by applying (see ALP7 Rough idle).
With the engine warm, leave it to idle for a few minutes (3 to 5 minutes):
– If it stalls and the fault reappears, replace the regulator.
– If it does not stall, stabilise the engine speed at 2000 rpm(1 minute) then accelerate at full load until it cuts out.
If the engine stalls, contact the Techline
If the engine does not startor there is no timing:
first, replace the regulator and if the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-378
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
VP036INHIBIT FUEL SUPPLY
NOTESThis command enables you to disable the supply to the injectors.
This command is carried out with the engine switched off, and ignition on.
This command allows the injectors to be locked, so that starting is not possible.
Command VP036 allows the engine compressions to be checked in complete safety without disconnecting the
injector connectors or the TDC sensor.
Procedure to follow: (cylinder no. 1 is located on the flywheel end).
– Remove all the heater plugs, connect the compression gauge.
– Position the gear lever in neutral (manual gearbox) or on position P (automatic gearbox).
– Depress the brake pedal and maintain this position.
– Activate command VP036.
– Try to start the vehicle.
– Check the engine compressions.
Start the procedure again on another cylinder.
WARNING
Keep the brake pedal depressed for the length of the test.
Re-establish control of the injectors using command VP037 Stop fuel supply inhibition.
EDC16C36_V44_VP036/EDC16C36_V4C_VP036/EDC16C36_V48_VP036/EDC16C36_V50_VP036/EDC16C36_V54_VP036/
EDC16C36_V58_VP036EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-379
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
VP037CANCEL FUEL SUPPLY INHIBITION
NOTESThis command restores the fuel supply to the injectors.
This command is carried out with the engine switched off, and ignition on.
The command allows the supply to the injectors to be re-established, following an engine compression test.
Run command VP037, and try to start the vehicle.
If the vehicle does not start, start the procedure again.
EDC16C36_V44_VP037/EDC16C36_V4C_VP037/EDC16C36_V48_VP037/EDC16C36_V50_VP037/EDC16C36_V54_VP037/
EDC16C36_V58_VP037EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-380V9 MR-372-J84-13B450$180.mif
13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
NOTESOnly refer to these customer complaints after a complete check with the diagnostic
tool.
No dialogue with engine management computer ALP1
Starting difficult or impossibleALP2
Poor performanceALP4
Irregular engine operationALP5
External leaks from the fuel circuit ALP6
Rough idleALP7
Oil leaks from the turbocharger ALP8
Noises of the turbochargerALP9
Exhaust fumesALP10
Particle filter warning light comes on too often ALP11
DIESEL INJECTION
Fault finding – Customer complaints

13B-383
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP2 Starting difficult (or impossible)
NOTESBefore analysing this customer complaint, check that there are no faults, and the
conformity (or otherwise) of the parameters and statuses, using the diagnostic
tool.
If the customer complaint is not eliminated, perform the following checks.
Is it difficult or impossible to start the engine?
PART A:
Check the engine earths.
If the engine speed is less than 200 rpm, refer to Technical Note 6014A, Checking the charging circuit, Starter
fault finding, Starter.
If an engine speed of 200 rpm is achieved with starter motor in operation, PR055 Engine speed.
If the engine speed shown on CLIP is zero and the engine is running, check the resistance of the engine speed
sensor between the following connections:
– Connection code 3BG,
– Connection code 3BL,
of component 149.
Replace the sensor if the resistance is not between 200 Ω and 270 Ω at 20°C.
Check the continuity and insulation of the following connections:
– Connection code 3BG,
– Connection code 3BL,
between components 120 and 149.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: precautions for repairs), repair the wiring; otherwise replace the wiring.
Check the conformity of the engine earths (oxidation, tightness, etc.).
Check the mounting and condition (overheating) of the sensor.
Replace if necessary.
Check the synchronisation of the camshaft sensors and the engine speed sensors with the display of ET238
Synchronisation. If synchronisation is not active, refer to the checks described in DF195 Camshaft/engine
speed consistency.
Check the fuel circuit for leaks using test 3 Low pressure circuit check.
If test 3: Low pressure circuit check is correct.
PART
B
Impossible
Difficult
EDC16C36_V44_ALP02/EDC16C36_V4C_ALP02/EDC16C36_V48_ALP02/EDC16C36_V50_ALP02/EDC16C36_V54_ALP02/
EDC16C36_V58_ALP02EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-384
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP2
CONTINUED 1
Test the high pressure fuel circuit:
Run the scenario SC035 High pressure fuel circuit fault finding (see Interpretation of commands).
Check that the heater plugs are actuated using the AC037 Preheating relay command.
Check the tightness and the condition of the inlet circuit: run test 4: Turbocharged air inlet circuit check and
follow the procedure.
Check that the exhaust is not blocked, run test 1 Exhaust system check and follow the procedure.
Check the consistency of the signal from the engine coolant temperature sensor.
Check the operation of the rail pressure regulator (DRV) using command AC011 Rail pressure regulator.
Check the timing setting.
End of part A
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-385
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP2
CONTINUED 2
Is there diesel fuel in the fuel tank?Fill the tank with diesel fuel.
Bleed the low and high pressure diesel circuit.
Does the starter motor work properly?
Ensure that the engine speed reaches PR055
Engine speed > ~ 200 rpm with the starter in
operation, Consult Technical Note 6014A, Checking the
charging circuit, 16A, Starter fault finding,
Starter.
Using the diagnostic tool, check the conformity of the immobiliser: ET003 Immobiliser must be INACTIVE.
ET003 not
in order, or
immobiliser warning light
permanently onET003 correct
(immobiliser code
warning light off)
Consult the fault finding procedure for the
immobiliser.Continue the fault finding procedure with Part A
of this fault finding chart.
PART
B
NO
YES
NO
YES
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58