2011 RENAULT SCENIC fuel

13B-36V9 MR-372-J84-13B450$090.mif
DIESEL INJECTION
Fault finding – Fault summary table13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
FaultDTC code in
hexadecimalLevel 1 fault
warning light
(orange
SERVICE
warning light)Level 2 fault
warning light
(red STOP
warning light)No fault
warning
light litOBD
warning
light lit
DF060 Misfiring on cylinder 2 302 - - 1.DEF -
DF061 Misfiring on cylinder 3 303 - - 1.DEF -
DF062 Misfiring on cylinder 4 304 - - 1.DEF -
DF065 Combustion misfire 300 - - 1.DEF -
DF069 Impact detected signal 1620 - 1.DEF - -
DF086 Coolant pump relay
control circuit2600CC.1/CC.0/
CO/ 1.DEF---
DF091 Vehicle speed signal 500 - - 1.DEF -
DF098 Fuel temperature
sensor circuit180 - - CC.0/CO.1 -
DF107 Computer memory 62F 1.DEF - - 1.DEF
DF119 Camshaft sensor
signal340 1.DEF/2.DEF - - -
DF120 Engine speed sensor
signal335 - 1.DEF/2.DEF - -
DF151 Main relay circuit 685 1.DEF/2.DEF - - -
DF165 Accelerator pedal
position sensor circuit2299 - 1.DEF/2.DEF 3.DEF -
DF195 Camshaft/engine
speed sensor consistency16 - - 1.DEF -
DF196 Pedal sensor circuit
gang 1225CO.0/CC.1/
1.DEF---
DF198 Pedal sensor circuit
gang 22120CO.0/CC.1/
1.DEF---

13B-37V9 MR-372-J84-13B450$090.mif
DIESEL INJECTION
Fault finding – Fault summary table13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Management of instrument panel warning lights according to the faults notified.
*temp: temperatureFaultDTC code in
hexadecimalLevel 1 fault
warning light
(orange
SERVICE
warning light)Level 2 fault
warning light
(red STOP
warning light)No fault
warning
light litOBD
warning
light lit
DF200 Atmospheric pressure
sensor2226 1.DEF/2.DEF - -1.DEF/
2.DEF
DF209 EGR valve position
sensor circuit409 - - CC.1/CO.0CC.1/
CO.0
DF221 Clutch contact signal 830 - - 1.DEF -
DF226 Damper valve circuit 120CO/CC.0/CC.1/
CC/1.DEF/
2.DEF-3.DEF-
DF228 Brake signal 571 - -1.DEF/
2.DEF-
DF232 Coolant pressure
sensor circuit530 - - CC.0/CO.1CC.0/
CO.1
DF249 Injector control 62B - 1.DEF - -
DF272 EGR valve control
circuit487 - -CO/CC.1/
CC.0/CCCO/CC.1/
CC.0/CC
DF276 Injector code
programming611 1.DEF/2.DEF - - -
DF293 Water in diesel fuel
detector2269 - - 1.DEF -
DF308 Clogged particle filter 242F X - - -
DF309 Particle filter
downstream temp* sensor242A - - CO.1/CC.0 -
DF310 Particle filter upstream
temp* sensor2031 CO.1/CC.0 - -CO.1/
CC.0
DF311 Number of failed
regenerations exceeded1435 X - - -

13B-51V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF007
CONTINUED 3
1.DEF
2.DEFNOTESThe fault is declared present or stored after an attempt to
start or after starting, with the engine cold, several hours
after the last trip (the difference in the coolant temperature
from the last engine stop and the present attempt to start
must be at least 60°C).
The level 1 warning light is on.
Check the condition of the rail pressure sensor connector (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, component code 1032).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check that there are no external diesel leaks from the high pressure fuel circuit.
Check the continuity and for the absence of interference resistance on the following connections:
– connection code 3LZ between components 120 and 1032,
– connection code 3LX between components 120 and 1032,
– connection code 3LY between components 120 and 1032.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
With the ignition on and the engine stopped for over 1 minute:
View parameter PR038 Rail pressure.
– If the pressure is below 90 bar, the sensor is in order.
– If the pressure is above 90 bar, contact the Techline.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-108V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF065
CONTINUED
DF065 appears on the diagnostic tool when the engine management computer has detected a fault during the
combustion phase several times in succession.
Several components may be responsible:
– the piston rings,
– the piston,
– the valves,
– the injector,
– the heater plug sealing.
Check that the stored injector codes are consistent with those engraved on each injector. If not, run command
SC002 Enter injector codes, and follow the procedure.
When dealing with a number of misfiring faults, check the fuel conformity by running test 11 Diesel fuel
conformity check.
Check the engine compressions.
Carry out the necessary repairs.
If the fault is still present, apply test 10: Incorrect injector operation.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-113V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF098
PRESENT
OR
STOREDFUEL TEMPERATURE SENSOR CIRCUIT
CC.0: Short circuit to earth
CO.1: Open circuit or short circuit to +12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the ignition is switched on.
– Engine running
Special notes:
If the fault is present:
– the fuel temperature safe value PR063 Fuel temperature = 100°C.
Use bornier Elé. 1681 for all operations on the engine management computer
connectors.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
CC.0
NOTESNone.
Check the condition of the fuel temperature sensor connector (see Wiring Diagram Technical Note, Mégane II
ph2, Scénic II ph2, component code 1066).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Measure the resistance of the fuel temperature sensor between the following connections:
– Connection code 3FAB of component 1066.
– Connection code 3LD of component 1066.
Replace the sensor if resistance is less than 85Ω or greater than 50 kΩ.
EDC16C36_V44_DF098/EDC16C36_V4C_DF098/EDC16C36_V48_DF098/EDC16C36_V50_DF098/EDC16C36_V54_DF098/
EDC16C36_V58_DF098
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-114V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF098
CONTINUED
Check the insulation to earth of the following connection:
– Connection code 3FAB between components 1066 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the wiring of the particle filter downstream temperature sensor, component code 1288, is present (with or without
the sensor being present), check the electrical insulation in relation to + 12 V between the following connections:
•3XU between components 120 and 1288,
•3TG between components 120 and 1288.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
CO.1
NOTESNone.
Check the condition of the fuel temperature sensor connector (see Wiring Diagram Technical Note, Mégane II
ph2, Scénic II ph2, component code 1066).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
Measure the resistance of the fuel temperature sensor between the following connections:
– Connection code 3FAB of component 1066.
– Connection code 3LD of component 1066.
Replace the sensor if resistance is less than 85Ω or greater than 50 kΩ.
Check the continuity and insulation to + 12 V on the following connections:
– Connection code 3FAB between components 1066 and 120.
– Connection code 3LD between components 1066 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-125
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF165
PRESENT
OR
STOREDACCELERATOR PEDAL POSITION SENSOR CIRCUIT
1.DEF: No signal
2.DEF: Accelerator pedal sensor locked
3.DEF: Detection of accelerator pedal depressed at same time as brake pedal.
1.DEF
2.DEF
NOTESPriorities when dealing with a number of faults:
Deal with fault DF012 Sensor supply no. 2 voltage first, if
it is present or stored.
Conditions for applying the fault finding procedure to a
stored fault:
The fault occurs if the brake pedal and the accelerator pedal
are depressed simultaneously for more than 1 second.
Special notes:
If the fault is present,
–the level 2 warning light illuminates if 1.DEF or 2.DEF is
present,
– turbocharging and cruise control are not authorised,
– the engine speed is fixed at 1400 rpm,
– cruise control/speed limiter function unusable,
– limitation of the quantity of fuel injected.
Use bornier Elé.1681 for any operations on the computer
connectors.
Use Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2.
EDC16C36_V44_DF165/EDC16C36_V4C_DF165/EDC16C36_V48_DF165/EDC16C36_V50_DF165/EDC16C36_V54_DF165/
EDC16C36_V58_DF165EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-159
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF293
PRESENT
OR
STOREDWATER IN DIESEL FUEL SENSOR
1.DEF: Open circuit on the line or water present in the diesel fuel
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the ignition is switched on,
– a road test.
Special notes:
If the fault is present,
– risk of engine destruction if fault DF293 not taken into account,
– water in diesel warning light on.
Use bornier Ele. 1681 for all operations on the engine management computer
connector.
IMPORTANT
Please observe the cleanliness guidelines and safety advice.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF293/EDC16C36_V4C_DF293/EDC16C36_V48_DF293/EDC16C36_V50_DF293/EDC16C36_V54_DF293/
EDC16C36_V58_DF293EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58