2011 RENAULT SCENIC check engine

13B-359
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC031OPERATIONAL FAULT FINDING OF CYLINDERS
NOTESThis command is used to run fault finding on the performance of each cylinder and
each injector.
To run this command, select scenario SC031 on the diagnostic tool.
Reminder: cylinder no. 1 is located at the timing end.
Procedure to be followed:
– select scenario SC031,
– once the conditions have been met, press the confirm button; the test will take approximately 5 minutes,
– the tool displays “cylinder no. 1 cut-off” and there will be a perceptible engine speed variation when the
cylinder is cut off; then the same procedure for the other three cylinders,
–the diagnostic tool displays the results,
– end of test.
Interpretation of correct results:
– If the displayed results are “VALID”, it means that the entire cylinder and injector assembly is in order. There is
no need for any operation.
Results Interpretation of results
Cylinder 1 VALID No operation
Cylinder 2 VALID No operation
Cylinder 3 VALID No operation
Cylinder 4 VALID No operation
– If a displayed result is “INVALID”, it means the cylinder or injector is not correct.
Difference compared to average Results Interpretation of results
Cylinder XNegative number or
Positive numberINVALIDCarry out the checks
described below.
EDC16C36_V4C_SC031/EDC16C36_V48_SC031/EDC16C36_V50_SC031/EDC16C36_V54_SC031/EDC16C36_V58_SC031 EDC16 C36
Program No.: 91
Vdiag No.: 4C, 48, 50,
54, 58

13B-360
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC031
CONTINUED
If the result of scenario SC031 is not confirmed, check the engine compressions:
Use a compression gauge and run command VP036 Fuel supply inhibition (see Interpretation of commands).
Run compressions on all cylinders.
Are the compressions correct?
Check the cylinder block.Check the fitting of the injector and repair if necessary.
Otherwise change the injector concerned.
After replacing the injector, follow the injector code programming
procedure (see Replacement of components), run SC036
Reinitialise programming, and select the number of the injector
replaced.
IMPORTANT
When removing and refitting an injector, follow the cleanliness guidelines and safety advice (see MR 364
(Mégane II) or 370 (Scénic II), Mechanical, 13B, Diesel injection, Diesel injector: Removal - Refitting).
NOYES
EDC16 C36
Program No.: 91
Vdiag No.: 4C, 48, 50,
54, 58

13B-361
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC035HIGH PRESSURE FUEL CIRCUIT FAULT FINDING
NOTESThis command is used to interpret the state of the high pressure fuel circuit (high
pressure pump, rail, injectors and high pressure supply pipes).
To run this command, select scenario SC035 on the diagnostic tool.
Procedure to be followed:
– select scenario SC035 High pressure fuel circuit fault finding,
– follow the instructions then “confirm”,
– with the command in progress: do not operate on the vehicle,
– switch off the engine at the end of the test,
– the tool displays the results,
– end of test.
Interpretation of correct results:
– If the results displayed are OK, the entire high pressure fuel circuit is in order. There is no need for any operation.
Stage X
(X is the variable from 1 to 4)Rising time
Rail pressureDrop off time
Rail pressureInterpretation of results
Stage X OK OK No operation
Stage 5 OK No operation
Interpretation of incorrect results:
– Is one of the value definitions for the various displayed stages is “TOO SLOW” or “TOO FAST”, see the
following table:
Stage X
(X is the variable from 1 to 4)Rising time
Rail pressureDrop off time
Rail pressureInterpretation of results
Stage X TOO SLOW TOO SLOW Check 1
Stage X TOO SLOW TOO FAST Check 2
Stage X TOO SLOW OK Check 3
Stage X OK TOO SLOW Check 4
Stage X OK TOO FAST Check 5
Stage 5 TOO FAST Check 5
EDC16C36_V4C_SC035/EDC16C36_V48_SC035/EDC16C36_V50_SC035/EDC16C36_V54_SC035/EDC16C36_V58_SC035 EDC16 C36
Program No.: 91
Vdiag No.: 4C, 48, 50,
54, 58

13B-363
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC036REINITIALISE PROGRAMMING
NOTESThis command is used to reset the computer parameters according to the type of
operation or component repaired or replaced from the following list:
– the injectors
– the EGR valve,
– the damper valve,
– after particle filter replacement (Vdiag 48, 50 only),
– after particle filter regeneration with the diagnostic tool (VDiag 48, 50 only),
– after replacing the injection computer with no save option (VDiag 48, 50 only).
Ignition on and engine stopped.
To run this command, in the CLIP tool, select scenario SC036 Reinitialise programming.
Procedure to be followed:
– on the main screen, select the component to reinitialise after a mechanical operation (removal - refitting or
replacement of component),
–select YES then OK to begin reinitialisation,
–select end on the configuration completed screen to return to the main screen,
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16 C36, check the tool connection and the computer supply. before switching on
the ignition again.
End of procedure.
EDC16C36_V44_SC036/EDC16C36_V4C_SC036/EDC16C36_V48_SC036/EDC16C36_V50_SC036/EDC16C36_V54_SC036/
EDC16C36_V58_SC036EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-365
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
RZ005PROGRAMMING
NOTESThis command enables you to reinitialise the entire computer configuration according
to the vehicle.
Ignition on and engine stopped.
Command RZ005 reconfigures the computer.
if the computer has no configuration data,
run command RZ005 to enter the options fitted on the vehicle:
– air conditioning,
– cruise control/speed limiter.
These options are detected by the computer even if command RZ005 is not used.
the computer is configured as soon as the one of the vehicle's optional system components is operated.
EDC16C36_V44_RZ005/EDC16C36_V4C_RZ005/EDC16C36_V48_RZ005/EDC16C36_V50_RZ005/EDC16C36_V54_RZ005/
EDC16C36_V58_RZ005EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-366
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
RZ034COMPUTER MEMORY
NOTESIMPORTANT
Only use this command if DF107 Computer Memory is Present.
Ignition on and engine stopped.
Command RZ034 reinitialises the computer memory.
With the ignition on:
– Use command RZ034.
– Switch off the ignition and wait for the message Communication lost with computer.
– Switch on the ignition again.
– Configure the injector codes using command SC002 Enter injector codes
– Run the programming commands (see configuration and programming).
– Switch off the ignition and wait for the message Communication lost with computer.
Perform a road test to reinitialise the vehicle parameters.
EDC16C36_V44_RZ034/EDC16C36_V4C_RZ034/EDC16C36_V48_RZ034/EDC16C36_V50_RZ034/EDC16C36_V54_RZ034/
EDC16C36_V58_RZ034EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-367
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC004TURBOCHARGING SOLENOID VALVE
NOTESPerform this fault finding procedure:
– following interpretation of an unresolved fault or
– after processing the interpretation of PR041 Turbocharging pressure or
– after a customer complaint (loss of power, smoke etc.).
Ignition on and engine stopped.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
1. The following procedure is for checking that the turbocharger and its control circuit are working
properly.
Check the sealing of the high pressure air circuit, run test 3 Low pressure circuit check
Pipe not joined or pierced, pressure sensor disconnected or poorly fitted (seal present), exchanger pierced.
To test the exchanger: stabilise the engine speed between 3500 and 4000 rpm with the vehicle stopped and check
that there are no leaks.
Measure the resistance of the turbocharging pressure solenoid valve between the following connections:
– Connection code 3MG,
– Connection code 3FB,
of component 1475.
Replace the solenoid valve if its resistance is not: 20 Ω ± 2 at +23°C.
Check the continuity, insulation, and the absence of interference resistance on the following connections:
– Connection code 3MG between components 1475 and 120.
– Connection code 3FB between components 1475 and 983.
Run command AC004, if a faint whistling noise is heard along with a clicking from the solenoid valve, go to step
2, otherwise check the operation of the computer output stage:
Vehicle under + after ignition feed, clear the faults displayed by the diagnostic tool.
With the voltmeter in the direct current position:
With the turbocharging solenoid valve connected, connect the voltmeter earth lead to connection 3MG of
component 1475 and the positive lead to connection3FB.
Run command AC004, the voltmeter should display four successive voltages of 2.4 V ± 0.2 V.
If the measurement is not correct, contact the Techline.
EDC16C36_V44_AC004/EDC16C36_V4C_AC004/EDC16C36_V48_AC004/EDC16C36_V50_AC004/EDC16C36_V54_AC004/
EDC16C36_V58_AC004EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-368
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC004
CONTINUED
2. Turbocharger control circuit check:
– With the engine stopped, make sure that the control rod is in the resting position.
– Start the engine and make sure that the control rod actuates to the upper stop.
(when the engine is switched off, the control rod should return to the rest position)
If the control rod does not move correctly, carry out the following checks:
1) Control vacuum check:
– Disconnect the solenoid valve inlet hose and connect it to a pressure gauge.
– Start the engine and run it at a stable idle speed.
– If the vacuum does not reach 400 mbar ± 150: check the vacuum pressure circuit from the vacuum pump.
– Stop the engine, reconnect the intake hose and go to step no. 2.
2) Solenoid valve control check:
– Disconnect the solenoid valve outlet hose.
– Start the engine and run it at a stable idle speed.
– Place your hand on the solenoid valve and block the outlet union with your thumb.
– If there is no perceptible vibration of the solenoid valve, contact the Techline.
3) Solenoid valve operation check:
– Connect the pressure gauge to the solenoid valve outlet union.
– Start the engine and run it at a stable idle speed.
If the vacuum does not reach 400 mbar ± 150, replace the solenoid valve.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58