2011 RENAULT SCENIC wiring

13B-376
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC039
CONTINUED
–Check for +12 V on connection BP71 of component 188 and on connection 49B of component 262.
–Check for earth on connection 49A of component 188 and on connection MAS of component 262.
If the tests are ok, replace the defective fan.
If not, carry out the following operations:
Check the continuity, insulation and the absence of interference resistance on the following connections:
– Connection code 49B between components 262 and 335.
– Connection code MAS between components 262 and MAS.
– Connection code 49A between components 188 and 337.
– Connection code BP71 between components 188 and 597.
– Connection code BP71 between components 335 and 597.
– Connection code 3FB,
– Connection code 3JP,
between components 335 and 120.
– Connection code MAS between components 337 and MAS.
– Connection code 3FB,
– Connection code 3JP,
between components 337 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-377
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC103EGR BY-PASS
NOTESCarry out this fault finding procedure when the interpretation of fault DF304 EGR
bypass circuit has not been resolved.
Ignition on and engine stopped.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
Measure the resistance of the EGR bypass solenoid valve between the following connections:
– Connection code 3TP,
– Connection code 3FB,
of component 1301.
43 Ω to 49 Ω at +25°C.
32 Ω to 37 Ω at -40°C
If the resistance is not correct, replace the EGR by-pass solenoid valve.
Check the continuity, insulation and absence of interference resistance on the following connections:
– Connection code 3TP between components 1301 and 120.
– Connection code 3FB between components 1301 and 983.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If you notice no valve movement when running command AC103, ensure that the computer output stage is
functioning:
Vehicle under + after ignition feed, clear the faults displayed by the diagnostic tool.
With the voltmeter in the direct current position:
With the EGR BY-PASS solenoid valve connected, connect the voltmeter earth lead to connection3TP of
component1301 and the positive lead to connection3FB.
Run command AC103, the voltmeter should display four successive readings which are approximately equal to
the 12 V battery voltage.
If the voltmeter indicates no control or a continuous voltage, contact the Techline.
If activation has run correctly, check the control vacuum:
– Disconnect the solenoid valve inlet hose and connect it to a pressure gauge.
– Start the engine and run it at a stable idle speed.
– If the vacuum pressure does not reach 800 mbar ± 100: check the vacuum pressure circuit from the vacuum
pump.
Repair if necessary.
EDC16C36_V44_AC103/EDC16C36_V4C_AC103/EDC16C36_V48_AC103/EDC16C36_V50_AC103/EDC16C36_V54_AC103/
EDC16C36_V58_AC103EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-381
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
13B
ALP1 No dialogue with engine management computer
STEP 1
Check the conformity of the vehicle type and the domain selected on the tool.
Check that the tool is not faulty by trying to establish dialogue with a computer on another vehicle.
Check the supply to the diagnostic socket:
+ Before ignition.
+ After ignition.
Earth.
Check (according to wiring diagram and equipment):
– The conformity of the after ignition fuse.
– The conformity of the injection relay mounting.
The conformity of the injection relay:
65 Ω ± 5 between the following connections:
– Connection code BP37 of component 983.
– Connection code 3AA of component 983.
infinite resistance between connections (open contact):
– Connection code BP37 of component 983.
– Connection code 3FB of component 983.
resistance < 0.2 Ω between the following connections (contact closed):
– Connection code BP37 of component 983.
– Connection code3FB of component983.
Disconnect the engine management computer and check that there are no conducting parts on the computer
studs. If this reveals any kind of impurity, rectify it and try to establish dialogue.
If the fault is still present, place the bornier Elé. 1681 on the engine harness:
Check for continuity and absence of interference resistance on the following multiplex connections:
– Connection code 133B between components 120 and 225.
– Connection code 133C between components 120 and 225.
Check for + 12 V on connections 3FB and AP29 of component 120.
Check for earth on connections NT of component 120.
A
EDC16C36_V44_ALP01/EDC16C36_V4C_ALP01/EDC16C36_V48_ALP01/EDC16C36_V50_ALP01/EDC16C36_V54_ALP01/
EDC16C36_V58_ALP01
DIESEL INJECTION
Fault finding – Fault Finding Chart
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-383
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP2 Starting difficult (or impossible)
NOTESBefore analysing this customer complaint, check that there are no faults, and the
conformity (or otherwise) of the parameters and statuses, using the diagnostic
tool.
If the customer complaint is not eliminated, perform the following checks.
Is it difficult or impossible to start the engine?
PART A:
Check the engine earths.
If the engine speed is less than 200 rpm, refer to Technical Note 6014A, Checking the charging circuit, Starter
fault finding, Starter.
If an engine speed of 200 rpm is achieved with starter motor in operation, PR055 Engine speed.
If the engine speed shown on CLIP is zero and the engine is running, check the resistance of the engine speed
sensor between the following connections:
– Connection code 3BG,
– Connection code 3BL,
of component 149.
Replace the sensor if the resistance is not between 200 Ω and 270 Ω at 20°C.
Check the continuity and insulation of the following connections:
– Connection code 3BG,
– Connection code 3BL,
between components 120 and 149.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: precautions for repairs), repair the wiring; otherwise replace the wiring.
Check the conformity of the engine earths (oxidation, tightness, etc.).
Check the mounting and condition (overheating) of the sensor.
Replace if necessary.
Check the synchronisation of the camshaft sensors and the engine speed sensors with the display of ET238
Synchronisation. If synchronisation is not active, refer to the checks described in DF195 Camshaft/engine
speed consistency.
Check the fuel circuit for leaks using test 3 Low pressure circuit check.
If test 3: Low pressure circuit check is correct.
PART
B
Impossible
Difficult
EDC16C36_V44_ALP02/EDC16C36_V4C_ALP02/EDC16C36_V48_ALP02/EDC16C36_V50_ALP02/EDC16C36_V54_ALP02/
EDC16C36_V58_ALP02EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-391
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP7 Rough idle
NOTESBefore analysing this customer complaint, check that there are no faults, and the
conformity (or otherwise) of the parameters and statuses, using the diagnostic
tool.
If the customer complaint is not eliminated, perform the following checks.
Check the sealing and condition of the inlet circuit by running Test 4 Turbocharged air circuit check.
Check the low pressure circuit
check the engine parameters:
– Check the update of the engine management computer calibration (last calibration).
– Check the conformity of the IMA codes (using the Identification screen on the Clip diagnostic tool).
– Check the charging circuit (see Technical Note 6014A Checking the charging circuit)
– To check the conformity of the engine speed signal, check:
– The wiring.
– The flywheel position and the condition of the flywheel teeth.
– The position and tightness of the engine speed sensor.
– Check the fuel flow correction from station to station, run Test 10 Poor injector operation.
Check the connections and wiring of the injectors.
Check the connections and wiring of the engine management computer to the injectors.
Repair if necessary.
A
EDC16C36_V44_ALP07/EDC16C36_V4C_ALP07/EDC16C36_V48_ALP07/EDC16C36_V50_ALP07/EDC16C36_V54_ALP07/
EDC16C36_V58_ALP07EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-416V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST10 Incorrect injector operation
Part A: Fuel regulation balance check for each injector (individual correction):
– In the CLIP diagnostic tool, choose the Fuel circuit sub-function.
– With the engine idling and the fuel temperature > 50°C, view the flow correction values of each injector (individual
correction), i.e.:
– PR364 Cylinder no. 1 fuel flow correction.
– PR405 Cylinder no. 2 fuel flow correction.
– PR406 Cylinder no. 3 fuel flow correction.
– PR365 Cylinder no. 4 fuel flow correction.
The flow correction range by injector is between -5 mg/st and +5 mg/st without reaching these values.
If this has not already been carried out, check the injector connections and wiring.
– Check the connections and wiring of the engine management computer to the injectors.
– Repair if necessary.
–Check the IMA injector codes, comparing the IMA codes on the injectors (the IMA codes must be read from left
to right) and the IMA codes read in the CLIP diagnostic tool.
– If the IMA codes are correct, continue the fault finding procedure,
– If not, enter the incorrect IMA codes using command SC002 Enter injector codes (see Interpretation of
commands).
To validate the repair, consult the Part B Confirmation of flow correction fault finding for each injector
(individual correction).
CASE No. 1: If at least one of the values is greater than or equal to + 5 mg/st
– Check the valve clearance.
– Check the status of the engine and the compressions (using the CLIP diagnostic tool or using a compression
gauge).
– If the compression test reveals a cylinder fault, carry out the necessary repairs.
– If the compression is correct, check the fitting conformity of the injector (see MR 364 (Mégane II) or 370 (Scénic
II), 13B, Diesel injection, Diesel injector: Removal - Refitting)
Ensure that each injector has only one heat protection washer.
Check the fuel regulation again for each injector (individual correction).
– Otherwise, replace the injector and check the presence of the sealing washer. Modify the IMA code using the
command SC002 Enter injector codes (see Interpretation of commands).
–Apply the Part B Confirmation of flow correction fault finding for each injector (individual correction) to
confirm the fault finding.
EDC16C36_V44_TEST10/EDC16C36_V4C_TEST10/EDC16C36_V48_TEST10/EDC16C36_V50_TEST10/EDC16C36_V54_TEST10/
EDC16C36_V58_TEST10
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58