2011 RENAULT SCENIC wheel torque

13B-66V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF026
PRESENT
OR
STOREDCYLINDER 1 INJECTOR CONTROL CIRCUIT
CO: Open circuit
CC: Short circuit
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after:
– with the engine running,
– a road test.
Special notes:
If the fault is present:
– engine torque limited for CO,
– engine stops for CO on more than one injector,
–the level 2 warning light comes on for CC and 1.DEF,
–the level 1 warning light comes on for CO,
–the European On Board Diagnostic warning light is lit.
– engine cut-off for CC and 1.DEF.
Use bornier Elé.1681 for all operations on the engine management computer.
After replacing an injector, run commands SC002 Enter injector codes and SC036
Reinitialisation of programming, follow the described procedures.
IMPORTANT
Cylinder no. 1 is located on the engine flywheel end.
Please observe the cleanliness guidelines and safety advice.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This test enables the condition and the conformity of the engine wiring harness to be
checked.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF026/EDC16C36_V4C_DF026/EDC16C36_V48_DF026/EDC16C36_V50_DF026/EDC16C36_V54_DF026/
EDC16C36_V58_DF026
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-68V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF027
PRESENT
OR
STOREDINJECTOR CYLINDER 2 CONTROL CIRCUIT
CO: Open circuit
CC: Short circuit
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after:
– with the engine running,
– a road test.
Special notes:
If the fault is present:
– engine torque limited for CO,
– engine stops for CO on more than one injector,
–the level 2 warning light comes on for CC and 1.DEF,
–the level 1 warning light comes on for CO,
–the European On Board Diagnostic warning light is lit.
– engine cut-off for CC and 1.DEF.
Use bornier Elé.1681 for all operations on the engine management computer.
After replacing an injector, run commands SC002 Enter injector codes and SC036
Reinitialisation of programming, follow the described procedures.
IMPORTANT
Cylinder no. 1 is located on the engine flywheel end.
Please observe the cleanliness guidelines and safety advice.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This test enables the condition and the conformity of the engine wiring harness to be
checked.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF027/EDC16C36_V4C_DF027/EDC16C36_V48_DF027/EDC16C36_V50_DF027/EDC16C36_V54_DF027/
EDC16C36_V58_DF027
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-70V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF028
PRESENT
OR
STOREDCYLINDER 3 INJECTOR CONTROL CIRCUIT
CO: Open circuit
CC: Short circuit
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after:
– with the engine running,
– a road test.
Special notes:
If the fault is present:
– engine torque limited for CO,
– engine stops for CO on more than one injector,
–the level 2 warning light comes on for CC and 1.DEF,
–the level 1 warning light comes on for CO,
–the European On Board Diagnostic warning light is lit.
– engine cut-off for CC and 1.DEF.
Use bornier Elé.1681 for all operations on the engine management computer.
After replacing an injector, run commands SC002 Enter injector codes and SC036
Reinitialisation of programming, follow the described procedures.
IMPORTANT
Cylinder no. 1 is located on the engine flywheel end.
Please observe the cleanliness guidelines and safety advice.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This test enables the condition and the conformity of the engine wiring harness to be
checked.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF028/EDC16C36_V4C_DF028/EDC16C36_V48_DF028/EDC16C36_V50_DF028/EDC16C36_V54_DF028/
EDC16C36_V58_DF028
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-72V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF029
PRESENT
OR
STOREDCYLINDER 4 INJECTOR CONTROL CIRCUIT
CO: Open circuit
CC: Short circuit
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after:
– with the engine running,
– a road test.
Special notes:
If the fault is present:
– engine torque limited for CO,
– engine stops for CO on more than one injector,
–the level 2 warning light comes on for CC and 1.DEF,
–the level 1 warning light comes on for CO,
–the European On Board Diagnostic warning light is lit.
– engine cut-off for CC and 1.DEF.
Use bornier Elé.1681 for all operations on the engine management computer.
After replacing an injector, run commands SC002 Enter injector codes and SC036
Reinitialisation of programming, follow the described procedures.
IMPORTANT
Cylinder no. 1 is located on the engine flywheel end.
Please observe the cleanliness guidelines and safety advice.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF029/EDC16C36_V4C_DF029/EDC16C36_V48_DF029/EDC16C36_V50_DF029/EDC16C36_V54_DF029/
EDC16C36_V58_DF029
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58