2011 RENAULT SCENIC Engine And Peripherals EDC16 Workshop Manual

13B-329
MR-372-J84-13B200$828.mif
V13
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP 8
CONTINUED 1
Is an oil leak present only at the casing of the compressor section?
YES NO
The turbocharger is not faulty. The oil leak is from another engine
component and the oil is flowing onto the turbocharger.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-330
MR-372-J84-13B200$828.mif
V13
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP 8
CONTINUED 2
Is an oil leak present at the turbocharger oil supply inlet or outlet?
YESNO
Check the turbocharger oil supply inlet and outlet
Check for a loose interface (inlet or outlet) that is the cause of the
oil leak.
Is the suspected interface properly tightened?
YES
Replace only the seal or the pipe of the section concerned (see MR 364 (Mégane II), 370 (Scénic II) or
395 (Laguna II), Mechanical, 12B, Turbocharging).
Is an oil leak present at the interfaces of the turbine casing and the exhaust pipes?
YES NO
The turbocharger is not faulty. There is probably another fault in the engine.
Mark the component that is the source of the leak and refer to the repair manual (see MR 364 (Mégane II), 370
(Scénic II) or 395 (Laguna II), 10A Engine and peripherals).
NO
Tighten the pipe concerned.
end of the procedure
End of procedure.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-331
MR-372-J84-13B200$828.mif
V13
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP 9 Particle filter warning light comes on too often
NOTESBefore dealing with this customer complaint, check that there are no faults
except DF312 Speed request and the conformity (or otherwise) of the
"parameters" and "status" using the diagnostic tool. Deal with the other faults
first.
If the customer complaint is not eliminated, perform the following checks.
Have the last 10 regeneration attempts failed?
Is the distance of PR412 Distance of last
successful regeneration less than all the
parameters of group 2? (PR794 to PR803
Regeneration failure record no. 1 to no. 10).
NO
Is at least one status for group 1 = STATUS4?
YES
YESAre all the regeneration
failures linked to engine cut-
off?
See parameter for the group
(ET706 Engine status record
no. 1 to ET715 Engine status
record no. 10)
(E.g.: ET706 STOPPED)
NO
Symptom
not
confirmed
YESOutput 1
NO
Check that there are
no leaks or
blockages in the
exhaust pipe,
Repair if necessary.
Carry out an After-
Sales regeneration if
not already
performed. To do
this, see SC017
Particle filter
regeneration in
Interpretation of
commands.
Output 2
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16_V50_ALP9/EDC16_V58_ALP9/EDC16_V5C_ALP9/EDC16_V18_ALP9/EDC16_V1C_ALP9/EDC16_V20_ALP9
A
B

13B-332
MR-372-J84-13B200$828.mif
V13
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP 9
CONTINUED 1
Recognition of parameters corresponding to the start of successful
regenerations.
Make adjustments to align the parameter groups.
Group 1 Regeneration start record no. 1 to 10
And
Group 2 Regeneration failure record no. 1 to 10
For each parameter in group 1, if there is no parameter in group 2 in the next
30 miles (50 km), note this down as a successful regeneration (R). If there is
one, this means a failure (e).
Note group 1 here:
PR816: ____ ET742 ___
PR817: ____ ET743 ___
PR818: ____ ET744 ___
PR819: ____ ET745 ___
PR820: ____ ET746 ___
PR821: ____ ET747 ___
PR822: ____ ET748 ___
PR823: ____ ET749 ___
PR824: ____ ET750 ___
PR825: ____ ET751 ___Note group 2 here
PR794: _________
PR795: _________
PR796: _________
PR797: _________
PR798: _________
PR799: _________
PR800: _________
PR801: _________
PR802: _________
PR803: _________Type of regeneration
PR816: R E
PR817: R E
PR818: R E
PR819: R E
PR820: R E
PR821: R E
PR822: R E
PR823: R E
PR824: R E
PR825: R E
A
YES
CD
B

13B-333
MR-372-J84-13B200$828.mif
V13
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP 9
CONTINUED 2
vdiag 5c and 20 vdiag 50, 58, 18 and 1C
Has a parameter from group 1 reached
19.661 miles (32.768 km)?YES
NO
For each successful regeneration (R), look in group 1 for the next parameter in order of
distance whose status is STATUS4. is there at least one status?
YES
note down the 2 identified parameters and calculate
the interval between the 2 using the formula in the
table.
Is the calculated interval less than 198 miles
(330 km)?
YES
CD
E
E
NOOutput 3
NOOutput 4
(To be calculated for each successful regeneration)
Parameter PR412 = _________
Next parameter at STATUS 4 = __________
Interval = Next parameter at STATUS 4 – PR412
= ________ - _________
= _________
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-334
MR-372-J84-13B200$828.mif
V13
DIESEL INJECTION
Fault finding – Fault Finding Chart
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
ALP 9
CONTINUED 3
– Check the consistency between the IMA codes entered and the codes engraved on the injector bodies.
– Check that the particle filter differential pressure sensor is correctly positioned and connected (see MR 364
(Mégane II), 370 (Scénic II) or 395 (Laguna II), Mechanical, 19B Exhaust, Particle filter pressure sensor:
Removal – Refitting).
– Check the exhaust pipe (see test 1 Exhaust pipe check).
– Check the air inlet circuit (see test 4 Turbocharged air inlet circuit check).
– Check the air flowmeter (see test 5 Air flowmeter).
– Check the turbocharger (see test 2 Air line at the turbocharger, test 6 Turbocharger control solenoid
valve check and test 7 Turbocharger).
– Check the injectors (see test 9 Poor injector operation).
– Check the cylinder compression rates
If the fault has not been located and the customer complaint is still present, contact the Techline.
E
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-335
MR-372-J84-13B200$828.mif
V13
DIESEL INJECTION
Fault finding – Fault Finding Chart
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
Analysis of output for ALP9 Particle filter warning light comes on too frequently
ALP 9
CONTINUED 4
Output
no. Output conditionCause – type of
drivingRegeneratio
n frequencyWhat to tell the
customer?
Output 1The last 10 regeneration
attempts have failed due to
the engine cutting out.Regeneration failures
caused by engine cut-
off.No
regeneration
frequency
analysis.Explain to the customer
the need to wait until the
end of regeneration
(warning light goes out)
before switching off the
engine.
Output 2The last 10 regeneration
attempts have failed but not
because of the engine cutting
out.Inappropriate driving
profile…No
regeneration
frequency
analysis.Explain again to the
customer the driving
criteria for when the
warning light comes on.
Output 3After successful
regenerations stored in the
memory, the warning light did
not come on. The interval
cannot be calculated.Since the last
successful regeneration
recordings, the driving
profile has been such
that the warning lights
have not come on.Should be
normalVehicle correct
Output 4The interval between a
successful regeneration and
the particle filter warning light
coming on is correct (above
the lowest possible values).
The system does not have
any irregular components.Unfavourable driving
(urban zone,
underspeed etc.)Normal Vehicle correct
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-336
MR-372-J84-13B200$828.mif
V13
DIESEL INJECTION
Fault finding – Fault Finding Chart
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
ALP 10 Noise from the turbocharger
Apply Technical Note 5164A, Noise fault finding procedure.
Note:
Pay close attention to faulty components that might result in unjustified replacement of the turbocharger. For
example, whistling does not necessarily indicate damage to the turbocharger (this could be coming from the
exhaust, the timing, the gearbox, etc.).
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16_V50_ALP10/EDC16_V58_ALP10/EDC16_V5C_ALP10/EDC16_V18_ALP10/EDC16_V1C_ALP10/EDC16_V20_ALP10