2011 RENAULT SCENIC Engine And Peripherals EDC16 Workshop Manual

13B-17
MR-372-J84-13B200$108.mif
V13
DIESEL INJECTION
Fault finding – System operation
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
If regeneration whilst driving has not been possible, the driver should request After-Sales regeneration in the
following cases:
– the soot weight is greater than 56 g for Vdiag 18.
– the soot weight is greater than 59 g or the number of failed regenerations is greater than 10 for Vdiag 1C
and 20.
This regeneration is carried out in the workshop. It is essential to follow the instructions described in the
interpretation of commands SC017 Particle filter regeneration. To carry out regeneration safely (see Te c h n i c a l
Note 5040A, Recommendations for particle filter regeneration).
Warning light management:
Instrument panel display
The computer manages the data display on the instrument panel relating to engine operation. This involves six
functions:
– the pre-postheating warning light,
– the coolant temperature warning light or warning message;
– the level 1 fault warning light (non-critical fault),
– the level 2 fault warning light (emergency stop),
– the OBD warning light (European On Board Diagnostic),
– particle filter warning message or light.
These six functions are represented by 4 or 5 warning lights and/or messages displayed by the trip computer.
In addition, for vehicles fitted with a voice synthesiser the illumination of some warning lights may be accompanied
by a spoken message (refer to the Driver's Handbook for the vehicle concerned).
A 3 second visual inspection (automatic test procedure managed by the instrument panel) is carried out by the
injection computer when the ignition is switched on.
Orange pre-post heating/non-critical fault SERVICE warning light (level 1)
This light is used both as an in-operation indicator light and as a system fault indicator:
– Continuously lit with + after ignition feed:
Indicates plug preheating (this light goes out when preheating is complete and the engine is able to start).
– Continuously lit accompanied by the message Check injection or Electronic fault:
Indicates a level 1 fault (involving operation of the injection system in defect mode).
The driver should carry out repairs as soon as possible. IMPORTANT
The particle filter must be replaced after a period of time which largely depends on the grade of engine oil used.
This information is provided in the vehicle's Driver's handbook.
After replacing the particle filter, it is essential to reconfigure certain parameters in the computer (see SC036
Reinitialise programming).

13B-18
MR-372-J84-13B200$108.mif
V13
DIESEL INJECTION
Fault finding – System operation
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
Temperature warning light/red EMERGENCY STOP (level 2)
This indicator light is used both as an in-operation indicator light and as a system fault warning light. It lights up for
3 seconds after the ignition is switched on (automatic test procedure managed by the instrument panel):
– Continuously or intermittently lit, accompanied by the message Engine overheating:
Indicates engine overheating (the driver is free to choose whether or not to stop the vehicle).
–For Vdiag 50, 58 and 5C: continuously lit, accompanied by the message faulty injection:
Indicates a level 2 fault (in this case, the injection is automatically cut after a few seconds).
The driver should carry out repairs as soon as possible.
–For Vdiag 18, 1C and 20: continuously lit, accompanied by the message Injection fault: stop the engine and by
a bleep, this indicates a level 2 fault.
In that case, the vehicle must be stopped immediately (when traffic conditions allow).
The driver should carry out repairs as soon as possible.
ORANGE OBD excess pollution warning light
An engine symbol accompanied by the message Check emission control.
This warning light comes on if the system has one or more OBD faults.
This warning light is used to alert the driver of any injection faults that could lead to excessive pollution, or if the
EOBD system has been deactivated.
The injection computer requests illumination of the OBD warning light for a present fault only after three consecutive
driving cycles.
If it flashes, reduce the engine speed until the flashing stops.
The driver should carry out repairs as soon as possible.
The 3 second visual inspection when the ignition is switched on (automatic test procedure managed by the
instrument panel) is carried out by the injection computer.
Special particle filter ORANGE warning light or warning message (depending on instrument panel)
– Vdiag 50, 58, 5C:
This warning light or message is used to warn the driver that the particle filter is clogged or a significant number of
failed regenerations while driving due to driving conditions not being favourable for regeneration.
Table of thresholds:
EnginePR383 Weight of soot in the
particle filterPR848 Number of failed
regenerations
Scénic II Mégane IIScénic II Mégane II
F9Q804 Vdiag 5035 35 3
F9Q803 Vdiag 58 and 5C50
7
F9Q804 Vdiag 58 and 5C58 50 7

13B-19
MR-372-J84-13B200$108.mif
V13
DIESEL INJECTION
Fault finding – System operation
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
– Vdiag 18, 1C, 20:
This warning light or message is used to warn the driver that the particle filter is loaded with particles. This happens
when the soot weight is greater than 46 g or the number of failed regenerations is greater than:
– 8 for Vdiag 18.
– 6 for Vdiag 1C and 20.
The driver must then drive as soon as possible at an average speed of 48 mph (80 km/h) subject to the road
conditions and authorised speed limits.
EOBD management. (European On Board Diagnostic):
The OBD (On Board Diagnostic) system permits the detection of any faults relating to the vehicle emission control
system (OBD EURO IV emission control standards being exceeded).
This system should be active for the entire life of the vehicle.
1. OBD fault display conditions
An OBD fault will be detected after 3 driving cycles and the following parameters will be saved in the computer:
– engine load,
– vehicle speed
– air temperature
– coolant temperature,
– turbocharging pressure,
– rail pressure,
– air flow,
– distance travelled in miles by the vehicle since activation of the OBD warning light.
It allows the driver to know whether the vehicle has a fault directly linked to the emission control system.

13B-20
MR-372-J84-13B200$108.mif
V13
DIESEL INJECTION
Fault finding – System operation
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
2. System faults displayed by the OBD
Only a few faults are displayed by the OBD system:
– DF001 Coolant temperature sensor circuit.
– DF003 Atmospheric pressure sensor circuit.
– DF011 Sensor supply voltage no. 1.
– DF012 Sensor supply voltage no. 2.
– DF013 Sensor supply voltage no. 3.
– DF038 Computer in 6.DEF EEPROM fault.
– DF040 Cylinder 1 injector circuit in CO Open circuit.
– DF041 Cylinder 2 injector circuit in CO Open circuit.
– DF042 Cylinder 3 injector circuit in CO Open circuit.
– DF043 Cylinder 4 injector circuit in CO Open circuit.
– DF054 Turbocharging solenoid valve control circuit in CC.0 Short circuit to earth.
– DF056 Air flowmeter circuit.
– DF209 EGR valve position sensor circuit.
– DF310 Particle filter upstream temp.* sensor.
– DF315 Particle filter diff.* pressure sensor.
– DF504 Automatic transmission.
– DF621 EGR valve jammed open.
– DF717 Particle filter upstream pressure.
– DF953 Particle filter absent.
Some repair operations require programming to ensure that certain engine components function correctly.
Follow the programming procedures (see Replacement of components), if replacing the exhaust gas
recirculation valve or an injector.
3. OBD fault clearing conditions
An OBD fault is cleared in several steps.
The fault present in the diagnostic tool will only be stored (after a repair operation) after the vehicle has been
driven 3 times.
The OBD warning light will only go out after these 3 trips.
The instrument panel warning light coming on does not automatically mean that the system has a fault.
In order for the OBD fault and display parameters to be cleared from the computer, the system requires
40 engine heating cycles.
An engine heating cycle is a driving cycle during which:
– the engine coolant temperature reaches at least 71.1°C,
– the engine coolant temperature varies by 22.2°C in relation to the engine starting temperature.
If one of these conditions is not fulfilled, the OBD fault will still be present or stored on the injection
computer.
* diff: differential
* temp: temperature

13B-21
MR-372-J84-13B200$144.mif
V13
13B
DIESEL INJECTION
Fault finding – Replacement of components
COMPUTER REPLACEMENT OR REPROGRAMMING
Two operations must be performed when replacing or reprogramming the computer:
SC003 Save computer data and SC001 Enter saved data.
– Run command SC003 Save computer data before replacing or reprogramming the computer. This enables
certain data to be saved in the diagnostic tool so that the new computer* can be reconfigured like the old one.
The saved data includes: injector codes, EGR programming, specific data for particle filter operation and vehicle
options.
– Run command SC001 Write saved data after replacing or reprogramming the computer. This command
enables the data (saved by the command SC003 Save computer data) to be rewritten in the new computer*.
If you cannot establish dialogue with the computer being replaced: you will not be able to save anything.
After replacing the computer:
– Manually enter the IMA codes for each injector by reading the code on each injector (see 13B, Diesel injection,
Replacement of components, Injector replacement).
– Enter the data specific to particle filter operation by running SC036 Reinitialise programming and select After
replacing the injection computer with no save option.
Exhaust gas recirculation valve data is programmed automatically the 1st time the new computer is switched on*.
* New computer or reprogrammed computer.
Specific to the cruise control/speed limiter operation to be carried out before reprogramming of the
computer:
Before reprogramming the injection computer, move the main cruise control/speed limiter switch to the rest
position. The information about the cruise control or the speed limiter displayed on the instrument panel
disappears.
Otherwise, if the main switch remains in the cruise control or speed limiter position during and after reprogramming,
the Cruise control/Speed limiter function will not be operational.
The procedure for resetting the function is as follows:
– Vehicle ignition on.
– Position the cruise control/speed limiter switch in the rest position (the computer then detects the rest position).
– Position the cruise control/speed limiter switch in the Cruise control position to activate the Cruise control
function.
– Position the cruise control/speed limiter switch in the Speed limiter position to activate the Speed limiter function. IMPORTANT
– Switch on the diagnostic tool (mains or cigarette lighter supply).
– Connect a battery charger.
– Cut off all the electrical consumers (lights, interior lighting, air conditioning, radio CD, etc.).
– Wait for the engine to cool (engine coolant temperature < 60° and air temperature < 50°).
– For Vdiags 50, 58, 5C, during (re)programming of the computer, the engine fan assemblies are actuated
automatically.
– For Vdiags 18, 1C, 20, during (re)programming of the computer, the instrument panel screen displays
“Oil pressure fault”.
– Ignore this message and do not take any action in connection with it.
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$144.mif

13B-22
MR-372-J84-13B200$144.mif
V13
DIESEL INJECTION
Fault finding – Replacement of components
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PROCEDURE:
Before replacing or reprogramming the computer:
– Select command SC003 Save computer data,
– if the following message appears: backup file exists, do you want to overwrite it?:
(this file corresponds to the last save carried out on the tool)
–select YES.
When the backup is complete, replace the computer or reprogram, then proceed to the next step.
After replacing or reprogramming the computer:
– Select command SC001 Write saved data, then follow the instructions given by the diagnostic tool,
– if the VIN has not been entered (see "Computer identification" on the main screen), select VP010 Enter VIN,
When both these commands have finished:
–switch off the ignition and wait 1minute before switching the ignition on again,
– then check the system faults, and clear any stored faults,
– otherwise, deal with faults that are present and clear the faults in the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
End of operation.IMPORTANT
Thermoplunger faults are displayed during reprogramming.
– DF032 Thermoplunger 1 relay control circuit,
– DF033 Thermoplunger 2 relay control circuit,
– DF034 Thermoplunger 3 relay control circuit,
– DF238 Thermoplunger 3 relay circuit,
– DF239 Thermoplunger 2 relay circuit,
– DF240 Thermoplunger 1 relay circuit.
In this case, configure the thermoplungers using configuration CF030 Thermoplungers.
IMPORTANT
– The injection computer retains the immobiliser code for life.
– The system has no security code.
– It is forbidden to perform tests with computers borrowed from the Parts Department or from another vehicle
which must then be returned.
– These computers are hard-coded.
– If the injection computer appears to be faulty, contact the Techline and refer to the fault finding log.

13B-23
MR-372-J84-13B200$144.mif
V13
DIESEL INJECTION
Fault finding – Replacement of components
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
REPLACING THE INJECTORS
After replacing one or more injectors, re-enter the IMA codes.
The system must be configured via the diagnostic socket using the RENAULT CLIP diagnostic tool.
PROCEDURE to be followed after replacing one or more injectors:
– make a note of the IMA code(s) engraved on the injector body,
– enter these codes in the computer using command SC002 Enter injector codes, then follow the instructions
given by the diagnostic tool,
– once the command has finished,
– switch off the ignition,
–wait 1 minute before switching on the ignition again,
– return to fault finding mode,
– select the function "Computer identification" on the main screen,
– check that the injector codes entered into the computer match those found on the bodies of the injectors:
– if the codes do not match, repeat the procedure for command SC002 Enter injector codes.
– if the codes do match, check the system faults and clear any stored faults,
– otherwise, deal with faults that are present and clear the faults in the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
End of operation.Note:
The IMA coding (individual injector correction) is a calibration made in production on each injector to adjust
the flow accurately.
These correction values are etched onto the Bakelite body of each injector (6 alphanumeric characters) and then
entered into the computer, which then controls each injector taking into account their manufacturing variance.
IMPORTANT
Cylinder no. 1 is located on the flywheel end.
IMPORTANT
Engines can only operate correctly if the correct IMA codes have been entered.
If no codes have been entered or if an invalid code has been entered, fault
DF276 Injector code programming is present and the engine will be in defect mode (significant engine
speed restriction).
If another injector’s code has been entered, the system will accept it but will make the wrong correction.
This could lead to engine damage, loss of performance and excessive pollution.
Always use the correct injector codes for the engine cylinder/computer.

13B-24
MR-372-J84-13B200$144.mif
V13
DIESEL INJECTION
Fault finding – Replacement of components
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
REPLACING OR CLEANING THE EXHAUST GAS RECIRCULATION (EGR) VALVE
After the exhaust gas recirculation valve has been replaced, the computer must store the new valve offset and the
offset measured when the ignition was last switched off, which corresponds to the valve closing.
Using this data, the computer can detect whether the valve is clogged or seized.
When the valve is replaced or cleaned, clear the stored offsets so that the program uses the new valve's offset
value.
The data linked to this strategy is compiled in the Antipollution/OBD sub-function.
– PR128 First EGR valve offset.
– PR129 Last EGR valve offset > or = PR128 for a new valve.
The PR128 and PR129 programming must be cleared every time the exhaust gas recirculation valve is replaced.
PROCEDURE:
– Run command SC036 Reinitialise programming.
–Select EGR valve as the type of operation, then follow the instructions given by the diagnostic tool.
When the command is finished,
– switch off the ignition,
–wait 1 minute before switching on the ignition again.
When the ignition is switched on again, the new EGR valve offset is automatically reprogrammed.
– start the vehicle to enable the latest EGR valve offset to be programmed,
– switch off the ignition,
–wait 1 minute before switching on the ignition again.
Reprogramming of the last EGR valve offset is stored in the computer.
– then check the system faults, and clear any stored faults,
– otherwise, deal with the faults that are present and clear the faults in the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
End of operation.Note:
When the reinitialisation is complete, the Emission control/OBD sub-function displays:
PR128 = PR129 > 100 %
Note:
When the new EGR valve offset has been reprogrammed, the Emission control/OBD sub-function displays:
10 % < PR128 < 40 %
PR129 > 100 %
Note:
When the last EGR valve offset has been reprogrammed, the Emission control/OBD sub-function displays:
10 % < PR128 < 40 %
10% < PR129 < 40%