2011 RENAULT SCENIC reset

13B-21
MR-372-J84-13B200$144.mif
V13
13B
DIESEL INJECTION
Fault finding – Replacement of components
COMPUTER REPLACEMENT OR REPROGRAMMING
Two operations must be performed when replacing or reprogramming the computer:
SC003 Save computer data and SC001 Enter saved data.
– Run command SC003 Save computer data before replacing or reprogramming the computer. This enables
certain data to be saved in the diagnostic tool so that the new computer* can be reconfigured like the old one.
The saved data includes: injector codes, EGR programming, specific data for particle filter operation and vehicle
options.
– Run command SC001 Write saved data after replacing or reprogramming the computer. This command
enables the data (saved by the command SC003 Save computer data) to be rewritten in the new computer*.
If you cannot establish dialogue with the computer being replaced: you will not be able to save anything.
After replacing the computer:
– Manually enter the IMA codes for each injector by reading the code on each injector (see 13B, Diesel injection,
Replacement of components, Injector replacement).
– Enter the data specific to particle filter operation by running SC036 Reinitialise programming and select After
replacing the injection computer with no save option.
Exhaust gas recirculation valve data is programmed automatically the 1st time the new computer is switched on*.
* New computer or reprogrammed computer.
Specific to the cruise control/speed limiter operation to be carried out before reprogramming of the
computer:
Before reprogramming the injection computer, move the main cruise control/speed limiter switch to the rest
position. The information about the cruise control or the speed limiter displayed on the instrument panel
disappears.
Otherwise, if the main switch remains in the cruise control or speed limiter position during and after reprogramming,
the Cruise control/Speed limiter function will not be operational.
The procedure for resetting the function is as follows:
– Vehicle ignition on.
– Position the cruise control/speed limiter switch in the rest position (the computer then detects the rest position).
– Position the cruise control/speed limiter switch in the Cruise control position to activate the Cruise control
function.
– Position the cruise control/speed limiter switch in the Speed limiter position to activate the Speed limiter function. IMPORTANT
– Switch on the diagnostic tool (mains or cigarette lighter supply).
– Connect a battery charger.
– Cut off all the electrical consumers (lights, interior lighting, air conditioning, radio CD, etc.).
– Wait for the engine to cool (engine coolant temperature < 60° and air temperature < 50°).
– For Vdiags 50, 58, 5C, during (re)programming of the computer, the engine fan assemblies are actuated
automatically.
– For Vdiags 18, 1C, 20, during (re)programming of the computer, the instrument panel screen displays
“Oil pressure fault”.
– Ignore this message and do not take any action in connection with it.
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$144.mif

13B-195
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CRUISE CONTROL/SPEED LIMITER DEACTIVATION
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system operation
programming.
Note:
Cruise control can be activated when the vehicle speed exceeds 20 mph (30 km/h).
Status ET415 shows various factors that cause deactivation of the cruise control/speed limiter function, due to a
driver request or the external environment (eg. STATUS 1).
IMPORTANT:
Clear the fault memory by running command RZ007 Fault memory, to reset this status to WITHOUT.
NONE
This status is present on the diagnostic tool if:
the computer has been reinitialised,
the computer has been reprogrammed.
STATUS 1Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving, with cruise control active (ET042:
Cruise control/Speed limiter: CRUISE CONTROL) and upon a traction control
request.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 1 without a traction control request (see38C, ABS).
STATUS 2Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes "STATUS 2" when driving with cruise control active (ET042
Cruise control/Speed limiter: CRUISE CONTROL) and the brake pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult the
interpretation of statuses ET704 and ET705 Brake contact No 1 and No 2.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET415/EDC16_V58_ET415/EDC16_V5C_ET415/EDC16_V18_ET415/EDC16_V1C_ET415/EDC16_V20_ET415

13B-200
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651
EGR PROGRAMMING CUT-OFF
STATUS DEFINITIONThis status indicates the EGR valve programming cut-off.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80 °C
NONE
No EGR cut-off, the EGR valve is working properly in accordance with the
computer programs.
STATUS 1, 5, 6, 7, 9,
10, 12, 13, 15, 19
23, 24Switch off the ignition and wait 1 minute.
Switch the ignition on and check for faults.
Check the engine battery voltage with the engine switched off and the engine running.
If no faults are present or stored, restart the vehicle and test at idle speed.
Do not accelerate too much and reach an engine speed that is too high.
STATUS 3, 14, 16Accelerate above idle speed for a few seconds.
STATUS 2Check that the clutch pedal (ET405 "Clutch pedal switch") is not pressed and that the
vehicle has stopped completely.
STATUS 4, 17Test the present and stored faults and repair.
STATUS 8Reset the EGR offsets by referring to the interpretation of command SC036
"Reinitialise programming" and select "EGR valve".
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET651/EDC16_V58_ET651/EDC16_V5C_ET651/EDC16_V18_ET651/EDC16_V1C_ET651/EDC16_V20_ET651

13B-298
MR-372-J84-13B200$756.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of commands
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
SC036
REINITIALISE PROGRAMMING
NOTESThis command is used to reset the computer parameters according to the type of
operation or component repaired or replaced from the following list:
– the EGR valve,
– the damper valve,
– after replacing the particle filter,
– after particle filter regeneration using the diagnostic tool,
– after injection computer replacement with no backup option,
Ignition on and engine stopped.
To run this command, select scenario SC036 on the CLIP diagnostic tool.
Procedure to be followed:
– on the main screen, select the component to reinitialise after an operation (removal – refitting or replacement of
component),
–select YES then OK to begin reinitialisation,
–select Finish on the Configuration performed screen to return to the main screen,
– end of operation.
– perform a complete powerlatch.
Features of the selections: After particle filter regeneration with diagnostic tool and After replacement of the
particle filter:
After using one of these 2 commands:
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and computer power supply.
–Then switch on the ignition again and clear the present or stored faults from the computer memory
(operation to be carried out within 3 minutes of switching on the ignition).
– Check the weight of soot: PR383 Weight of soot in the particle filter.
– If PR383
≥ 1 g. Apply the procedure for test 8 Manual clearing of the soot weight.
EDC16_V50_SC036/EDC16_V58_SC036/EDC16_V5C_SC036/EDC16_V18_SC036/EDC16_V1C_SC036/EDC16_V20_SC036