2011 RENAULT SCENIC engine

13B-184
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET088
REQUEST TO START COMPRESSOR
STATUS DEFINITIONACTIVE: This status indicates that the compressor is engaged.
INACTIVE: This status indicates that the compressor is not engaged.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Engine running, engine coolant temperature > 80 °C
ACTIVE
Status ET088 becomes ACTIVE if there has been a request for air conditioning (“AC” or
“AUTO” button pressed, with maximum cold) and if status ET004 Air conditioning
authorisation is YES.
The selection is made on the air conditioning control panel, the request for air
conditioning is transmitted to the UCH which in turn transmits the request to the
injection computer which either authorises or does not authorise compressor activation.
If the injection computer authorises compressor activation, it sends the compressor
activation request to the Protection and Switching Unit (Vdiag 18, 1C, 20 only) and
status ET088 becomes ACTIVE (climate control).
If the vehicle is equipped with manual air conditioning, the air conditioning request is
transmitted from the air conditioning control panel to the UCH which then accepts or
does not accept the air conditioning compressor coming on depending on the operating
status of the passenger compartment fan. When the request has been accepted, the
request to switch on the compressor is transmitted to the injection computer which
either authorises or does not authorise the compressor to start.
If the injection computer authorises compressor activation, it sends the compressor
activation request to the Protection and Switching Unit (Vdiag 18, 1C, 20 only) and
status ET088 becomes ACTIVE.
If there has been no compressor activation request and status ET088 remains ACTIVE
(see62A, Air conditioning).
Note:
Compressor operation is only authorised when the engine is running.
Compressor switch-on is finally requested by the Protection and Switching
Unit (Vdiag 18, 1C, 20 only).
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_ET088/EDC16_V58_ET088/EDC16_V5C_ET088/EDC16_V18_ET088/EDC16_V1C_ET088/EDC16_V20_ET088

13B-185
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET088
CONTINUED
Conformity check with engine stopped and ignition on
INACTIVE
Status ET088 is INACTIVE when there has been no air conditioning request and
when compressor activation has not been authorised (ET004 Air conditioning
authorisation is NO or when the driver switches off the air conditioning).
If compressor activation has been requested and status ET088 remains INACTIVE
(see 62A, Air conditioning).
Note:
Compressor operation is only authorised when the engine is running.
Compressor switch-on is finally requested by the Protection and Switching Unit
(Vdiag 18, 1C, 20 only).
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

13B-186
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET104
INJECTOR CODE USE
STATUS DEFINITIONNO: This status indicates that injector code use is not available.
YES: This status indicates that injector code use is available.
FA U LT Y: This status indicates that there has been an injector code use fault.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
NO
Status ET104 is NO if the computer is not configured to interpret the IMA codes
(individual injector correction)
Use command SC002 “Enter injector codes” (see Interpretation of commands).
YESStatus ET104 is YES if the IMA option (individual injector correction) is activated in
the injection computer.
All the injectors have IMA codes etched on the bakelite body, but not all computers
use them.
In the case of a computer configured with the IMA option, the injector codes must be
entered into the injection computer in the following scenarios:
– when one or more injectors is replaced,
– when the injection computer is replaced,
– when the injection computer is reprogrammed.
If the injector codes are not programmed after these operations, fault DF276
“Injector code programming” will be present and the engine will operate in defect
mode.
Use command SC002 Enter injector codes (see Interpretation of commands).
FA U LT YStatus ET104 is FA U LT Y if the computer does not have IMA codes in the memory.
Fault DF276 Injector code programming is present and the engine runs in defect
mode.
Run command SC002 Enter injector codes (see Command summary table).
If at the end of the procedure status ET104 remains FA U LT Y, contact Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET104/EDC16_V58_ET104/EDC16_V5C_ET104/EDC16_V18_ET104/EDC16_V1C_ET104/EDC16_V20_ET104

13B-187
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET111
SET NUMBER OF PASSENGER COMPARTMENT HEATING
RESISTORS
STATUS DEFINITIONYES: This status indicates that the number of activated passenger compartment
heating resistors is set by the injection computer.
NO: This status indicates that the number of passenger compartment heating resistors
can be freely controlled by the UCH.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
YES
Depending on the requirements of the injection system (power requirement, torque
reduction, etc.), the injection computer fixes the number of controlled passenger
compartment heating resistors (no more, no less).
Status ET111 becomes YES when the number of activated passenger compartment
heating resistors is set by the injection computer.
NODepending on the requirements of the injection system (power requirement, torque
reduction, etc.), the injection computer fixes the number of controlled passenger
compartment heating resistors (no more, no less).
Status ET111 becomes NO when the number of activated passenger compartment
heating resistors can be freely controlled by the UCH.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_ET111/EDC16_V58_ET111/EDC16_V5C_ET111/EDC16_V18_ET111/EDC16_V1C_ET111/EDC16_V20_ET111

13B-188
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET112
PASSENGER COMPARTMENT HEATING RESISTOR CUT-OFF
STATUS DEFINITIONYES: This status indicates that the passenger compartment heating resistors are
switched off at the request of the injection computer.
NO: This status indicates that the passenger compartment heating resistors can be
freely controlled by the UCH.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
YES
Depending on the requirements of the injection system (power requirements, torque
reduction, etc.), the injection computer cuts off the passenger compartment heating
resistors.
Status ET112 becomes YES when the passenger compartment heating resistors are
cut off at the request of the injection computer.
NODepending on the requirements of the injection system (power requirements, torque
reduction, etc.), the injection computer cuts off the passenger compartment heating
resistors.
Status ET112 becomes NO when the passenger compartment heating resistors can be
freely controlled by the UCH.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_ET112/EDC16_V58_ET112/EDC16_V5C_ET112/EDC16_V18_ET112/EDC16_V1C_ET112/EDC16_V20_ET112

13B-189
MR-372-J84-13B200$504.mif
V13
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET143
LOW-SPEED FAN ASSEMBLY RELAY CONTROL
STATUS DEFINITIONACTVE: This status indicates that the low-speed fan assembly relay is actuated.
INACTIVE: This status indicates that the low-speed fan assembly relay is not actuated.
NOTESIf the vehicle is fitted with air conditioning, the fan assembly electrical circuit contains
2 relays. The fan assembly speed 1 relay will be actuated when the engine coolant
temperature exceeds 96° and will be dedicated to cooling the engine as long as the
engine coolant temperature does not exceed 99°.
If the engine coolant temperature exceeds 99°, fan assembly speed 2 relay will be
actuated and the engine cooling fan will run more quickly.
ACTIVE
When the coolant reaches 96°C, the diesel computer actuates the low-speed fan
assembly relay and status ET143 becomes ACTIVE.
The relay then supplies the fan assembly and the cooling fan begins to turn.
Run command AC038 Low-speed fan unit relay and check visually that the cooling
fan is turning.
If this is not the case, carry out the following operations:
– check the condition of fuse FM15 (60A) and the motor relay R09,
– disconnect the low-speed and high-speed relays, check their operation and the
condition of the connections.
– repair if necessary,
– check for a + 12 V on connection 3FB of the low speed relay when it is actuated
then check the continuity and the absence of interference resistance on connection
3JN between components 120 and 597.
If the connection or connections are faulty and there is a repair method (see Technical
Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
INACTIVEIf the engine temperature is less than 96°C, the engine cooling fan cannot switch on
and the low-speed fan assembly relay cannot be actuated.
Sta tus ET143 becomes INACTIVE when the control relay and the engine cooling fan
are not supplied.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V18_ET143/EDC16_V1C_ET143/EDC16_V20_ET143EDC16
Program No: C1
Vdiag No: 18, 1C, 20

13B-190
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET144
HIGH-SPEED FAN ASSEMBLY RELAY CONTROL
STATUS DEFINITIONACTIVE: This status indicates that the high-speed fan assembly relay is actuated.
INACTIVE: This status indicates that the high-speed fan assembly relay is not
actuated.
ACTIVE
When the coolant reaches 99°C, the diesel computer activates the high-speed fan
assembly relay and status ET144 becomes ACTIVE.
The relay then supplies the fan assembly and the cooling fan begins to turn.
Run command AC039 High-speed fan unit relay and visually check that the cooling
fan is turning. If this is not the case, carry out the following operations:
– check the condition of fuse FM15 (60A) and the motor relay R10,
– disconnect the fan unit relays, check their operation and the condition of the
connections,
– repair if necessary,
– check for a + 12 V on connection 49B of components 597 and 262, when the high-
speed relay is actuated.
Check the continuity and the absence of interference resistance on the following
connections:
–Connection codes 3JP and 49B between components 120, 957 and 262.
If the connection or connections are faulty and there is a repair method (see Technical
Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
INACTIVEIf the engine temperature is less than 99°C, the engine cooling fan cannot switch on
and the high-speed fan assembly relay should not be actuated.
Status ET144 becomes INACTIVE when the control relay and the engine cooling fan
are not supplied.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V18_ET144/EDC16_V1C_ET144/EDC16_V20_ET144

13B-191
MR-372-J84-13B200$504.mif
V13
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET205
ET206
ET207
THERMOPLUNGER NO. 1, 2, 3 RELAY CONTROL
STATUS DEFINITIONACTIVE: This status indicates that the control of thermoplunger relay no. 1, no.2 and
no. 3 is active.
INACTIVE: This status indicates that the control of thermoplunger relay no. 1, no.2 and
no. 3 is not active.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
ACTIVE
Statuses ET205, ET206, ET207 are ACTIVE when:
– the engine has been started,
– and the engine coolant temperature is low (< 15°),
– and the air temperature is low (< 5°).
This program allows the engine coolant to be heated and to enable the passenger
compartment to be heated.
To control the operation of the thermoplunger relays, run the following commands:
– AC063 Heating element no.1 relay.
– AC064 Heating element no.2 relay.
– AC031 “Heating element relay no.3”.
In the event of a fault, refer to the interpretation of faults:
– DF032 “Thermoplunger no. 1 relay control circuit”
– DF033 “Thermoplunger no. 2 relay control circuit”
– DF034 “Thermoplunger no. 3 relay control circuit”.
INACTIVEStatuses ET205, ET206 and ET207 are INACTIVE with the ignition on and the engine
stopped, or when the engine is warm.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_ET205/EDC16_V58_ET205/EDC16_V5C_ET205/EDC16_V18_ET205/EDC16_V1C_ET205/EDC16_V20_ET205/
EDC16_V50_ET206/EDC16_V58_ET206/EDC16_V5C_ET206/EDC16_V18_ET206/EDC16_V1C_ET206/EDC16_V20_ET206/
EDC16_V50_ET207/EDC16_V58_ET207/EDC16_V5C_ET207/EDC16_V18_ET207/EDC16_V1C_ET207/EDC16_V20_ET207 EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C