2011 RENAULT SCENIC ignition

13B-126
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
STARTING
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine stopped, ignition on.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
1 Power supplyET001: + After ignition
computer feedIgnition on
PRESENTIf the event of a fault, carry
out fault finding on
thecharge circuit.
PR071:Computer feed
voltage9 V < X < 16 VIf the event of a fault, carry
out fault finding on
the charge circuit
PR358: Sensor
reference
voltage3.47 V < X < 3.75 V
(Average of the
three sensor supply
voltages)In the event of a fault, consult
the interpretation of faults
DF011 Sensor feed voltage
no. 1, DF012 Sensor feed
voltage no. 2, and DF013
Sensor feed voltage no. 3.
2 Starting ET076: StartingAUTHORISED:
The injection system
authorises starting
or
PROHIBITED:
The injection system
does not authorise
starting.If status ET076 is
PROHIBITED, carry out fault
finding on the entire
multiplex network.
3 Engine operation ET038: EngineIgnition on
STOPPED
or
STALLEDNone
4 Synchronisation ET238: SynchronisationCOMPLETEDIn the event of a fault, consult
the interpretation of status
ET238.

13B-127
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
PROTECTION
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine stopped, ignition on.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
1Engine
immobiliserET341: Immobiliser
code
programmedYES or
NOIf status ET341
is locked on NO,
(See 87B, UCH).
ET003: Engine
immobiliserACTIVE
or
INACTIVEIf status ET003 is stuck at
ACTIVE, (See 87B, UCH
fault finding).
2 Vehicle impact ET077: Impact detectedYES or
NOIn the event of a fault, refer
to the interpretation of fault
DF069 Impact detected
signal.
3 Starting ET076: StartingAUTHORISED:
The injection system
authorises starting
or
PROHIBITED:
The injection system
does not authorise
starting.If status ET076 is stuck at
PROHIBITED, (See 87B,
UCH fault finding).

13B-128
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
MAIN COMPUTER STATUSES AND PARAMETERS
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
1 Vehicle impact ET077: Impact detectedYES or NOIn the event of a fault,
refer to the interpretation
of fault DF069 Impact
detected signal.
2 Power supplyET001:+ After ignition
computer feedPRESENT, ignition on
If there is a fault carry out
a fault finding test on
thecharge circuit.
PR071: Computer feed
voltage9V PR368: Sensor
reference
voltage3.47 V < X < 3.75 V
(Average of the three
sensor feed voltages)In the event of a fault,
consult the interpretation
of faults DF011 Sensor
feed voltage no. 1,
DF012 Sensor feed
voltage no. 2 and DF013
Sensor feed voltage no. 3.
PR076: Refrigerant
sensor voltage0V consult the interpretation
of fault DF049 Refrigerant
sensor circuit.
3 Engine running PR055: Engine speedIndicates the engine's
rotation speed in rpm.
PR055 = 800 rpmIn the event of a fault,
consult the interpretation
of fault DF005 Engine
speed sensor circuit.
4Injection
configurationET104: Injector code
useYES or NO
or
DEFECTIVEThis status indicates that the
IMA function is activated.
In the event of a fault,
consult the interpretation
of DF276 Injector code
programming.

13B - 137
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
COLD LOOP (continued)
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as examples.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
7 Engine coolingET022: Low speed fan
assembly
requestINACTIVE if air
conditioning not
switched onIf the motor-driven fan
assemblies are being
supplied continuously
without the air
conditioning being
active, the injection
system may be in defect
mode.
Carry out a system fault
test and consult the
interpretation of any faults. ET021: High speed fan
assembly
request
ET014: Fan assembly 1
checkRUNNING if air
conditioning is active
ET015: Fan assembly 2
checkRUNNING if
operating
temperature is
reached
8Coolant
temperaturePR064: Coolant
temperatureShows the engine
coolant temperature
in °C
Default value: 119 °CIn the event of a fault,
consult the interpretation
for DF001 "Coolant
temperature sensor
circuit".
9 Vehicle speed PR089: Vehicle speedGives the vehicle
speed in mph. This
parameter is
transmitted by the ABS
computer. This signal
is transmitted to the
injection on the
multiplex network.
With ignition on
PR089 = 0 mph (km/h)In the event of a fault, test
the multiplex network.
Refer to the ABS fault
finding notes for the
interpretation of possible
faults.

13B - 138
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DRIVER PARAMETERS
(*) PEDAL VOLTAGES - COLD, IGNITION OFF
(Average values given as examples).
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as examples.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1 Engine running PR055: Engine speedIndicates the engine's
speed in rpm
At idling speed
PR055= 800rpmIn the event of a fault,
consult the interpretation of
fault DF005 Engine speed
sensor circuit.
2Accelerator
pedal positionPR030: Accelerator
pedal position *Indicates the
accelerator pedal
position
If no pressure is
being applied to the
pedal PR030 = 0 %In the event of a fault,
consult the interpretation of
fault DF008 Pedal
potentiometer circuit
gang 1 or DF009 Pedal
potentiometer circuit
gang 2.
3 Sensor feedPR147: Pedal
potentiometer
gang 1 voltageAccelerator pedal
released
0.70 < PR147 < 0.80 VIn the event of a fault,
consult the interpretation of
fault DF011 Sensor feed
voltage no. 1
or
DF012 Sensor feed
voltage no. 2. PR148: Pedal
potentiometer
gang 2 voltageAccelerator pedal
released
0.35 < PR148 < 0.40 V
Pedal load 0 % 25 % 50 % 100 % 120 %
Gang 1 voltage 0.76 V 1.52 V 2.09 V 3.23 V 3.68 V
Gang 2 voltage 0.37 V 0.74 V 1.02 V 1.56 V 1.79 V

13B - 142
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
CRUISE-CONTROL/SPEED LIMITER (continued)
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
3Brake
switchET704:Brake
switch no. 1
signalIndicates the position of the
brake pedal
With the ignition on, pedal
released:
ET704 = ET705 = INACTIVEIn the event of a fault,
consult the
interpretation of
statuses ET704 and
ET705. ET705:Brake
switch no. 2
signal
4Clutch
SwitchET405:Clutch pedal
switchIndicates the position of the
clutch pedal
With the ignition on, pedal
released:
ET405 = INACTIVEIn the event of a fault,
consult the
interpretation of status
ET405.

13B - 143
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ENGINE COOLING
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Coolant
temperaturePR064:Coolant
temperatureShows the engine coolant
temperature in °C
Default value: 119 °CIn the event of a fault,
consult the
interpretation of DF001
Coolant temperature
sensor circuit.
2 Fan assembliesET022:Low speed
fan assembly
requestINACTIVE if air
conditioning not
switched onIf the fan assemblies
are supplied with the
ignition on, the
injection may be in
defect mode.
Carry out a system fault
test and consult the
interpretation of any
faults. ET021:High speed
fan assembly
request
ET014:Fan assembly
1 checkRUNNING if air
conditioning is active
ET015:Fan assembly
2 checkRUNNING if operating
temperature is reached
3 Sensor feed PR084:Coolant
temperature
sensor
voltageidle speed, engine warm
PR084 = 0.54 V
Safe value: 5 VIn the event of a fault,
consult the
interpretation of DF001
Coolant temperature
sensor circuit.

13B - 144
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
IGNITION/PREHEATING
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1 Power supply ET001:+ After
ignition
computer
feedPRESENT If the event of a fault, carry
out fault finding on the
charging circuit
2 Engine speed PR055: Engine
speedIndicates the engine's
speed in rpm
At idling speed
PR055 = 800 rpmIn the event of a fault,
consult the interpretation of
fault DF005 Engine speed
sensor circuit.
3TemperaturePR064: Coolant
temperatureShows the engine coolant
temperature in °C
Default value: 119 °CIn the event of a fault,
consult the interpretation of
DF001 Coolant
temperature sensor
circuit.
PR059:Inlet air
temperatureIndicates the inlet air
temperature
Default value: 20 °CIn the event of a fault,
consult the interpretation of
fault DF039 Inlet air
temperature sensor
circuit.
4 Preheating ET007:Preheating
unit controlidle speed, engine warm
ET007 = INACTIVEIn the event of a fault,
(ET007 locked in ACTIVE),
consult the interpretation of
fault DF017 Preheating
unit control circuit.