2011 RENAULT SCENIC water pump

13B-69
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF053
CONTINUED 3
2.DEF to
8.DEF
NOTESNone.
Check the operation of the overpressure valve if fitted to the vehicle, run test 6 Incorrect operation of the
overpressure valve.
In the event of rail overpressure:
Check that the injectors are operating correctly (see Component test, Test 1, Injector Test).
Check that the rail pressure sensor is operating correctly using command AC011 Rail pressure regulator.
Display parameter PR038 Rail pressure, and refer to the conformity check to check the operating values.
If these checks do not indicate any abnormality and if the fault is still present, replace the injection pump.
in the event of rail underpressure:
Check that the rail pressure sensor is operating correctly using command AC011 Rail pressure regulator.
Display parameter PR038 Rail pressure, and refer to the conformity check to check the operating values.
Check the low pressure diesel circuit priming.
Check the conformity of the diesel filter connections.
Check the condition of the filter (clogging and water saturation).
Check that there are no air bubbles between the filter and the high pressure pump.
Check the low and high pressure diesel fuel circuit sealing (visual inspections, odour, etc.): pump housing,
pressure relief valve, pipes, rail and injector unions, injector wells, etc.
Check that the injectors are operating correctly (see Component test, Test 1, Injector Test).
Carry out the necessary operations.
If the fault is still present, replace the injection pump.
If the fault is still present, replace the injection pump.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

13B - 200
DIESEL INJECTION
Fault finding - Interpretation of commands13B
V10 MR-372-J84-13B150$752.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
AC011
CONTINUED
Step 2
In the event of rail overpressure:
Check the operation of the injectors (see Components test, Test 1 Injector test).
Check the operation of the rail pressure sensor: interpretation of fault DF007 Rail pressure sensor circuit.
If these checks do not reveal any faults, and if the fault is still present, replace the rail pressure sensor.
In the event of rail underpressure:
Check the operation of the rail pressure sensor: interpretation of fault DF007 Rail pressure sensor circuit.
Check the low pressure diesel circuit priming.
Check the conformity of the diesel filter connections.
Check the condition of the filter (clogging and water saturation).
Check there are no air bubbles between the filter and the high pressure pump.
Check the high-pressure diesel circuit sealing, pump, pipes, unions (visual inspections + odours, etc.):
pump housing, pressure release valve, pipes, rail and injectors unions, injector wells, etc.
Check the conformity of the seal fitting on the pressure regulator.
Check the operation of the injectors: see Component test, Test 1 Injector test.
Carry out the necessary repairs.
AFTER REPAIRCarry out a road test followed by a diagnostic tool check.
Repeat the conformity check from the start.

13B-205
MR-372-J84-13B150$846.mif
V10
DIESEL INJECTION
Fault finding - Fault finding chart13B
ALP 2Starting faults
(or starting impossible)
NOTESBefore dealing with this customer complaint, check that there are no faults,
and he conformity (or otherwise) of the parameters and statuses using the
diagnostic tool.
If the customer complaint is not eliminated, perform the following checks.
Is starting difficult or impossible?
difficult
Check the engine earths.
Make sure that the engine speed reaches 250 rpm when the starter motor is operated, displayed in
the parameter screen.
Ensure that the correct fuel is being used. Run test 5 Diesel fuel conformity check.
Check the conformity of the fuel filter connections.
Ensure that the fuel filter is not saturated with water.
Check there are no air bubbles between the filter and the high pressure pump.
Check the operation of the preheating unit and heater plugs with command AC001 Preheating unit.
Check the condition of the air filter (clogging).
Check the seal of the high-pressure diesel circuit, pump, pipes, unions (visual checks + odours).
Check the position of the EGR valve: jamming or mechanical seizure.
Check the consistency of the signal from the engine coolant temperature sensor.
Check that the pressure regulator is working correctly (see the interpretation of command AC011 Rail
pressure regulator).
Check the operation of the injectors (too much return leakage, clogging, seizing) referring to Component
test, Test 1 Injector Test.
Check the compression balance, according to current consumption during the starting phase
(Compression test menu on the Clip tool).
In the event of imbalance, use a compression gauge to refine the reading (see the procedure in the Workshop
Repair Manual). After the operation, clear the faults caused by disconnecting the regulator and the heater
plugs.
impossible
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16_V44_ALP2 / EDC16_V48_ALP2 / EDC16_V4C_ALP2
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C

13B-209
MR-372-J84-13B150$846.mif
V10
DIESEL INJECTION
Fault finding - Fault finding chart13B
ALP 5 Irregular engine operation
NOTESBefore dealing with this customer complaint, check that there are no faults,
and the conformity (or otherwise) of the parameters and statuses using
the diagnostic tool.
If the customer complaint is not eliminated, perform the following checks.
If the engine bucks or races during gear changes, check the conformity of the clutch switch.
If the fault is still present:
– Ensure that the correct fuel is being used. Run test 5 Diesel fuel conformity check.
– Check the low pressure diesel circuit priming.
– Check the conformity of the low-pressure circuit connections.
– Check the conformity of the diesel filter and that it is not saturated with water (replace the filter if necessary).
– Check that there are no air bubbles between the filter and the high pressure pump.
– Check the conformity of the rail pressure (warm engine):
± 25 bar around the rail pressure value at idle speed, (the minimum to maximum variations in the rail
pressure at idle speed should not exceed 50 bar).
approximately 1350 bar under load with foot hard down on the accelerator.
In the event of a fault, apply the interpretation of command AC011 Rail pressure regulator.
Check the conformity of the air flow, apply the interpretation of parameter PR132 Air flow.
If the fault is still present:
– Check the injector operation using Test 1 Injector test.
– Check cylinder balancing using the CLIP function, Compression test physical measurement icon.
– Check engine compression where necessary.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16_V44_ALP5 / EDC16_V48_ALP5 / EDC16_V4C_ALP5EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C

13B-229
MR-372-J84-13B150$893.mif
V10
13B
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Tests
1
TEST5 Diesel fuel conformity check
WARNING
During this operation, it is essential to:
– refrain from smoking or bringing incandescent objects close to the work area,
– protect yourself against fuel splashes due to residual pressure in the pipes,
– wear safety goggles with side guards,
– wear leaktight gloves (Nitrile type).
IMPORTANT
– To avoid any corrosion or damage, protect the areas on which fuel is likely to run.
– To prevent impurities from entering the circuit, place protective plugs on all fuel circuit components
exposed to the open air.
Preparations:
Weigh an empty 1300 ml plastic cup (part no. 77 11 171 413) with its cover (part no. 77 11 171 416) using
electronic scales such as those used in body paint workshops (example: PANDA part no. 77 11 224 995).
Record the weight of the empty plastic cup.
This type of plastic cup is used to prepare paint.
Remove 1 L of fuel at the diesel filter outlet (see MR 364 (Mégane) or 370 (Scénic), Mechanical, 19C, Tank,
Fuel tank: Draining), using a pneumatic transfer pump (part no. 634-200) and place it in the 1300 ml plastic cup.
Cover the plastic cup with its cover and allow it to settle for approximately 2 minutes.
Is the fuel cloudy or does it
separate into two parts?Presence of water in diesel fuel, the fuel is not compliant.
Drain the fuel circuit, including the tank (see MR 364 (Mégane)
or 370 (Scénic), Mechanical, 19C, Tank, Fuel Tank:
Draining).
YES
NO
A
EDC16_V44_TEST5 / EDC16_V48_TEST5 / EDC16_V4C_TEST5