2011 RENAULT SCENIC injector

13B-128
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
MAIN COMPUTER STATUSES AND PARAMETERS
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
1 Vehicle impact ET077: Impact detectedYES or NOIn the event of a fault,
refer to the interpretation
of fault DF069 Impact
detected signal.
2 Power supplyET001:+ After ignition
computer feedPRESENT, ignition on
If there is a fault carry out
a fault finding test on
thecharge circuit.
PR071: Computer feed
voltage9V PR368: Sensor
reference
voltage3.47 V < X < 3.75 V
(Average of the three
sensor feed voltages)In the event of a fault,
consult the interpretation
of faults DF011 Sensor
feed voltage no. 1,
DF012 Sensor feed
voltage no. 2 and DF013
Sensor feed voltage no. 3.
PR076: Refrigerant
sensor voltage0V consult the interpretation
of fault DF049 Refrigerant
sensor circuit.
3 Engine running PR055: Engine speedIndicates the engine's
rotation speed in rpm.
PR055 = 800 rpmIn the event of a fault,
consult the interpretation
of fault DF005 Engine
speed sensor circuit.
4Injection
configurationET104: Injector code
useYES or NO
or
DEFECTIVEThis status indicates that the
IMA function is activated.
In the event of a fault,
consult the interpretation
of DF276 Injector code
programming.

13B-134
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
FUEL CIRCUIT (continued)
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
4FlowPR017: Fuel flow6 < X < 7 mg/st NONE
5 Rail currentPR006: Rail pressure
regulator current1320 < X < 1350 mA
Default value:
1600 mA or 4 mAIn the event of a fault,
consult the interpretation
of fault DF007 Rail pressure
sensor circuit.
PR007: Rail pressure
regulator current
setpoint1320 < X < 1350 mA
Default value:
1600 mA or 4 mA
6 Sensor voltagePR082: Fuel
temperature
sensor voltage1.5 Default value: 5 VIn the event of a fault,
consult the interpretation
of fault DF098 Fuel
temperature sensor
circuit.
PR080: Rail pressure
sensor voltage1.1 < X <1.2 V
Default value: 5 VIn the event of a fault, refer
to the interpretation of fault
DF013 Sensor supply
voltage no. 3.
7 Fuel flow
correctionPR364: Cylinder no. 1
fuel flow
correction
± 1 mg/stIf one of the fuel flow
correction parameters is
outside the permitted
tolerance values, consult
the interpretation of TEST
1 Injector Test. PR405: Cylinder no. 2
fuel flow
correction
PR406: Cylinder no. 3
fuel flow
correction
PR365: Cylinder no. 4
fuel flow
correction

13B - 147
DIESEL INJECTION
Fault finding - Status summary table13B
V10 MR-372-J84-13B150$517.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Status summary table
*RCH: Passenger compartment heating resistorTool Status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET004Air conditioning authorisation
ET007Preheating unit control
ET014Check cooling fan 1
ET015Check cooling fan 2
ET021High speed fan assembly request
ET022Low speed fan assembly request
ET035Reverse gear signal
ET038Engine
ET042Cruise control/speed limiter
ET076Starting
ET077Impact detected
ET078Air regulation
ET079Air conditioning present
ET088Compressor actuation request
ET104Injector code use
ET111RCH* number set
ET112RCH* cut-off
ET233Clutch pedal
ET238Synchronisation
ET341Immobiliser code programmed
ET405Clutch pedal switch
ET413Cruise control/speed limiter function
ET415Deactivation of cruise control/speed limiter
ET703Cruise control/speed limiter buttons
ET704Brake switch no. 1
ET705Brake switch no. 2
MR-372-J84-13B150$517.mif

DIESEL INJECTION
Fault finding - Interpretation of statuses13B
13B-164V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET104
INJECTOR CODE USE
NOTESOnly perform the tests if the statuses do not correspond with the system programming
functions.
YES
NO
Status ET104 is YES if the IMA option (individual injector correction) is activated in
the injection computer.
All the injectors have IMA codes etched on the bakelite body, but not all computers
use them.
In the case of a computer configured with the IMA option, the injector codes must be
entered into the injection computer in the following scenarios:
– when one or more injectors is replaced,
– when the injection computer is replaced,
– when the injection computer is reprogrammed.
If the injector codes are not programmed after these operations, fault DF276
Injector code programming will be present, and the engine will operate in defect
mode.
Run command SC002 Enter injector codes applying the procedure described in
the interpretation of this command.
Status ET104 is NO if the computer is not configured to interpret the IMA codes
(individual injector correction).
WARNING
A computer without the IMA option can be replaced by a computer with this option.
In this scenario status ET104 changes to YES after replacing the computer.
Fault DF276 Injector code programming will be present and the engine will operate
in defect mode.
In this case, run command SC002 Enter injector codes, applying the procedure
described in the interpretation of this command.
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
EDC16_V44_ET104/EDC16_V48_ET104/EDC16_V4C_ET104

13B-165
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET104
CONTINUED
FAULTYStatus ET104 is FAULTY if the computer does not have IMA codes stored.
Fault DF276 Injector code programming is present and the engine operates in defect
mode.
Run command SC002 Enter injector codes applying the procedure described in the
interpretation of this command.
If at the end of the procedure status ET104 remains FAULTY, contact the Techline.
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.

13B - 184
DIESEL INJECTION
Fault finding - Interpretation of parameters13B
V10 MR-372-J84-13B150$658.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
PR038
RAIL PRESSURE
NOTESPerform this fault finding procedure:
– after the interpretation of fault DF053 Rail pressure regulation function,
– after an inconsistency for PR038 noted in the Parameters menu,
– after the interpretation of the fault finding procedure for AC011 Rail pressure
regulator,
– following a customer complaint (starting faults, poor performance, stalling, etc.).
Check the continuity and the absence of interference resistance on the following connections:
Injection computer, brown 48-track connector
B, track G3Track 2 of the rail pressure sensor connector
Injection computer brown 48-track
connector B, track A4Track 3 of the rail pressure sensor connector
Injection computer, brown 48-track connector
B, track C4Track 1 of the rail pressure sensor connector
If all these connections are correct, check for fuel pressure sensor power supply:
+ 5 V Track 3 of the rail pressure sensor connector
Earth Track 1 of the rail pressure sensor connector
Repair if necessary.
Check the sealing of the low and high-pressure diesel circuits (visual inspections, odour) pump housing,
overpressure valve, pipes, rail and injector unions, injector wells, etc.
If all of the previous checks are correct, switch the ignition on, wait for more than 1 minute and display PR038 Rail
pressure.
If the value is less than 50 bar, the rail pressure sensor is correct. If it is greater than this value, replace the rail
pressure sensor and tighten it to 35 ± 5 Nm.
AFTER REPAIRRepeat the conformity check from the start.
EDC16_V44_PR038/EDC16_V48_PR038/EDC16_V4C_PR038

13B - 188
DIESEL INJECTION
Fault finding - Command summary table13B
V10 MR-372-J84-13B150$705.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Command summary table
Tool command Diagnostic tool title
SC001Write saved data
SC002Enter injector codes
SC003Save computer data
RZ001Fault memory
RZ002EGR programming adaptives
RZ005Programming
AC001Preheating unit
AC002EGR solenoid valve
AC004Turbocharging solenoid valve
AC011Rail pressure regulator
AC014Damper flap
VP010Enter VIN
MR-372-J84-13B150$705.mif

13B - 189
DIESEL INJECTION
13B
V10 MR-372-J84-13B150$752.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4CDIESEL INJECTION
Fault finding - Interpretation of commands
SC001
WRITE SAVED DATA
NOTESAll data must be backed up with command SC003 Backup computer data for this
command to be run.
Writing is carried out after the computer has been reprogrammed or replaced.
Confirming this command writes the data backed up using command SC003 Backup computer data.
The data is as follows:
– Vehicle-specific idle speed.
– Options available on the vehicle and managed by the computer (Example: Air conditioning).
– Injector calibration codes (if the vehicle is fitted with IMA).
– Programming of exhaust gas recirculation valve data.
They will configure the computer and will enable it to avoid:
– engine malfunction after reprogramming or replacing the computer,
– faulty interpretation of information provided by the CLIP tool.
AFTER REPAIRRestart the conformity check from the beginning.
EDC16_V44_SC001/EDC16_V48_SC001/EDC16_V4C_SC001
MR-372-J84-13B150$752.mif