2011 RENAULT SCENIC engine

13B - 140
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
CRUISE CONTROL/SPEED LIMITER
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Cruise
control/
speed
limiterPR089:Vehicle
speedIndicates the vehicle speed in
mph (km/h). This parameter is
transmitted by the ABS
computer. This signal is
transmitted to the injection on
the multiplex network.
At idling speed
PR089= 0mphIn the event of a fault, test
the multiplex network.
(See 38C, ABS) for the
interpretation of possible
faults.
PR130:Cruise
control
setpointIndicates the cruise control
limit speed
At idling speed
X = 0 mph (km/h)In the event of a fault, consult
the interpretation of statuses
ET703 Cruise control/Speed
limiter buttons and ET415
Cruise control/Speed limiter
deactivation.

13B - 141
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
CRUISE-CONTROL/SPEED LIMITER (continued)
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
2Cruise
control/
speed
limiter
(continued)ET415: Deactivation
of cruise
control/speed
limiterNONE
STATUS 1: Traction control
request
The cruise control and speed
limiter functions can be
deactivated by various
events.
In the event of a fault,
consult the interpretation of
statuses ET703 Cruise
control/Speed limiter
buttons and ET415 Cruise
control/Speed limiter
deactivation. STATUS 2: Brake pedal
depressed
STATUS 3: Clutch pedal
depressed
STATUS 4: Suspend button
pressed
STATUS 5: Cruise control or
speed limiter monitoring
STATUS 6: Gear lever in
neutral (manual gearbox) or
neutral position (automatic
transmission).
Note: the cruise control
can only be activated at
a speed of >18 mph
(30 km/h).STATUS 7: Inconsistency
between request and vehicle
speed
STATUS 9: Vehicle speed
monitoring
STATUS 10: Monitoring by
injection computer
ET703: Cruise
control/speed
limiter
buttonsINACTIVE: no button
pressed
In the event of a fault,
consult the interpretation of
statuses ET703 Cruise
control/Speed limiter
buttons and ET415 Cruise
control/Speed limiter
deactivation. INCREASE: increase button
pressed
DECREASE: decrease
button pressed
SUSPEND: Suspend button
pressed
RESUME: Resume button
pressed

13B - 142
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
CRUISE-CONTROL/SPEED LIMITER (continued)
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
3Brake
switchET704:Brake
switch no. 1
signalIndicates the position of the
brake pedal
With the ignition on, pedal
released:
ET704 = ET705 = INACTIVEIn the event of a fault,
consult the
interpretation of
statuses ET704 and
ET705. ET705:Brake
switch no. 2
signal
4Clutch
SwitchET405:Clutch pedal
switchIndicates the position of the
clutch pedal
With the ignition on, pedal
released:
ET405 = INACTIVEIn the event of a fault,
consult the
interpretation of status
ET405.

13B - 143
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ENGINE COOLING
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Coolant
temperaturePR064:Coolant
temperatureShows the engine coolant
temperature in °C
Default value: 119 °CIn the event of a fault,
consult the
interpretation of DF001
Coolant temperature
sensor circuit.
2 Fan assembliesET022:Low speed
fan assembly
requestINACTIVE if air
conditioning not
switched onIf the fan assemblies
are supplied with the
ignition on, the
injection may be in
defect mode.
Carry out a system fault
test and consult the
interpretation of any
faults. ET021:High speed
fan assembly
request
ET014:Fan assembly
1 checkRUNNING if air
conditioning is active
ET015:Fan assembly
2 checkRUNNING if operating
temperature is reached
3 Sensor feed PR084:Coolant
temperature
sensor
voltageidle speed, engine warm
PR084 = 0.54 V
Safe value: 5 VIn the event of a fault,
consult the
interpretation of DF001
Coolant temperature
sensor circuit.

13B - 144
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
IGNITION/PREHEATING
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1 Power supply ET001:+ After
ignition
computer
feedPRESENT If the event of a fault, carry
out fault finding on the
charging circuit
2 Engine speed PR055: Engine
speedIndicates the engine's
speed in rpm
At idling speed
PR055 = 800 rpmIn the event of a fault,
consult the interpretation of
fault DF005 Engine speed
sensor circuit.
3TemperaturePR064: Coolant
temperatureShows the engine coolant
temperature in °C
Default value: 119 °CIn the event of a fault,
consult the interpretation of
DF001 Coolant
temperature sensor
circuit.
PR059:Inlet air
temperatureIndicates the inlet air
temperature
Default value: 20 °CIn the event of a fault,
consult the interpretation of
fault DF039 Inlet air
temperature sensor
circuit.
4 Preheating ET007:Preheating
unit controlidle speed, engine warm
ET007 = INACTIVEIn the event of a fault,
(ET007 locked in ACTIVE),
consult the interpretation of
fault DF017 Preheating
unit control circuit.

13B - 145
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
STARTING
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1 Power supplyET001: + After ignition
computer feedPRESENTIf the event of a fault,
carry out fault finding on
the charging circuit
PR071: Computer feed
voltage9 V < X < 16 VIn the event of a fault,
carry out fault finding on
the charging circuit.
PR358: Sensor
reference
voltage3.47 < X < 3.75 V
(Average of the three
sensor feed voltages)In the event of a fault,
consult the interpretation
of faults DF011 Sensor
feed voltage no. 1, DF012
Sensor feed voltage no. 2,
and DF013 Sensor feed
voltage no. 3.
2 Starting ET076:StartingAUTHORISED:
The injection gives
authorisation to start
or
PROHIBITED:
The injection does not
give authorisation to
start.If status ET076 is
PROHIBITED, carry out
fault finding on the entire
multiplex network.
3 Engine operation ET038:EngineAt idling speed
RunningNone
4 Synchronisation ET238: SynchronisationPERFORMEDIn the event of a fault,
consult the interpretation
of status ET238

13B - 146
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
PROTECTION
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Engine
immobiliserET341: Code
programmedYES
or
NOIf status ET341 is stuck at
NO, (See 87B, UCH).
ET003: Engine
immobiliserACTIVE
or
INACTIVEIf status ET003 is stuck at
ACTIVE, (See 87B, UCH).
2 Vehicle impact ET077: Impact
detectedYES
or
NOIn the event of a fault,
consult the interpretation of
fault DF069 Impact signal
detected.
3 Starting ET076: StartingAUTHORISED:
The injection system
authorises starting
or
PROHIBITED:
The injection system
does not authorise
starting.If status ET076 is
PROHIBITED,
(See 87B, UCH).

13B - 147
DIESEL INJECTION
Fault finding - Status summary table13B
V10 MR-372-J84-13B150$517.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Status summary table
*RCH: Passenger compartment heating resistorTool Status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET004Air conditioning authorisation
ET007Preheating unit control
ET014Check cooling fan 1
ET015Check cooling fan 2
ET021High speed fan assembly request
ET022Low speed fan assembly request
ET035Reverse gear signal
ET038Engine
ET042Cruise control/speed limiter
ET076Starting
ET077Impact detected
ET078Air regulation
ET079Air conditioning present
ET088Compressor actuation request
ET104Injector code use
ET111RCH* number set
ET112RCH* cut-off
ET233Clutch pedal
ET238Synchronisation
ET341Immobiliser code programmed
ET405Clutch pedal switch
ET413Cruise control/speed limiter function
ET415Deactivation of cruise control/speed limiter
ET703Cruise control/speed limiter buttons
ET704Brake switch no. 1
ET705Brake switch no. 2
MR-372-J84-13B150$517.mif