2011 Peugeot RCZ Owner's Manual

1/
INSTRUMENTS AND CONTROLS


Warning lamp



is on



Cause



Action/Observations








Rear foglamps


fi xed.
The rear foglamps are switched on.
Turn the ring on the stalk rearwards to switch off the rear
foglamps.





Diesel engine
pre-heating


fi xed. The ignition switch is at the
2nd position (ignition on). Wait until the warning lamp has switched off before starting.
The duration for which the warning lamp is on is
determined by the climatic conditions.





Parking brake


fi xed. The parking brake is applied or
not properly released. Release the parking brake to switch off the warning lamp,
keeping your foot on the brake pedal.
Observe the safety recommendations.
For further information on the parking brake, refer to the
"Driving" section.





Front foglamps


fi xed.
The front foglamps are switched on.
Turn the ring on the stalk rearwards twice to switch off the
front foglamps.



Passenger's
front airbag
fi xed on the
seat belt and
passenger's front
airbag warning
lamps display. The control switch, located on
the passenger's side of the
dashboard, has been placed in
the "ON"
position.
The passenger's front airbag is
activated.
In this case, do not install a
"rear facing" child seat. While you do not have a rear-facing child seat fi tted to
the front passenger seat, it is recommended that the
passenger's front airbag be activated.
On the other hand, before fi tting a rear-facing child seat,
you must turn the control switch to the "OFF"
position.

32










Deactivation warning lamps

If one of the following warning lamps comes on, this confi rms that the
corresponding system has been switched off intentionally.
It is accompanied by an audible signal and a message on the screen.
Depending on your version of instrument panel, illumination of the
deactivation lamp is also accompanied by :


- a pictogramme in the central instrument panel screen and a
message in the multifunction screen,
or

- a pictogramme and a message in the central instrument panel
screen.




Warning lamp



is on



Cause



Action/Observations






Passenger's
front airbag


fi xed, in the seat
belt and front
passenger's
airbag warning
lamps display. The control switch, located
on the passenger's end of the
dashboard, is set to the OFF

position.
The passenger's front airbag is
deactivated.
You can install a "rear-facing"
child seat on the front seat Before installing a "rear-facing" child seat on the front seat,
it is essential
to deactivate the passenger's front airbag.
On the other hand, where no "rear-facing" child seat is
present, it is recommended that the airbag be reactivated:
set the control to the ON
position.






ESP/ASR


fi xed. The button, located in the centre
of the dashboard, is pressed. Its
indicator lamp is on.

The following functions are deactivated.


- electronic stability
programme (ESP),

- anti-slip regulation or traction
control (ASR),

- automatic operation of
hazard warning lamps. Press the button again to reactivate these functions
manually. Its indicator lamp switches off.
These functions are reactivated automatically when the
vehicle is started.

1/
5090
130
INSTRUMENTS AND CONTROLS












COOLANT TEMPERATURE INDICATOR

With the engine running, when the needle is:


- in zone A
, the temperature is correct,

- in zone B
, the temperature is too high; the maximum temperature
warning lamp and the central STOP
warning lamp come on,
accompanied by an audible signal and an alert message in the
screen.

You MUST stop as soon as it is safe to do so.

Wait a few minutes before switching off the engine.
Contact a PEUGEOT dealer or a qualifi ed workshop.
















ENGINE OIL LEVEL INDICATOR

This information is displayed for a few seconds when the ignition is
switched on, at the same time as the service information.
The vehicle must be on level ground and the engine must have
been off for more than 30 minutes for this level check to be
accurate. After driving for a few minutes, the temperature and pressure in the
cooling system increase.
To top up the level:


)
wait for the engine to cool,

)
unscrew the cap by two turns to allow the pressure to drop,

)
when the pressure has dropped, remove the cap,

)
top up the level to the "MAX" mark.

offkm/h90
OIL OKOil level
correct

34

Oil level correct

This is indicated by the fl ashing of "OIL"
or an alert message in the
instrument panel, accompanied by illumination of the service warning
lamp and an audible signal.
If the lack of oil is confi rmed by a check using the dipstick, it is essential
that the level is topped up to prevent damage to the engine.
This is indicated by the fl ashing of "OIL--"
or the appearance of an alert
message in the instrument panel. Contact a PEUGEOT dealer or a
qualifi ed workshop.


Lack of oil

Oil level indicator fault
Dipstick

Refer to the "Checks" section to locate the dipstick and the oil fi ller cap
on your engine.
There are 2 marks on the dipstick:


-
A
= max; never exceed this level (risk of damage to
the engine),

-
B
= min; top up the level via the oil fi ller cap, using
the grade of oil suited to your engine.


Oil level
correct
Oil level
incorrect
Oil level measurement
invalid

1/
INSTRUMENTS AND CONTROLS






SERVICE INDICATOR

This information is displayed for a few seconds when the ignition is
switched on. It informs the driver when the next service is due, in
accordance with the manufacturer's servicing schedule.
The point at which the service is due is calculated from the last indicator
zero reset. It is determined by two parameters:


- the distance travelled,

- the time elapsed since the last service.


More than 1 800 miles (3 000 km) remain before the next service is due

When the ignition is switched on, no service information appears on the
instrument panel central screen.


Between 600 miles (1 000 km) and 1 800 miles (3 000 km)
remain before the next service is due
For 7 seconds after the ignition is switched on, the spanner symbolising
the service operations comes on. The instrument panel central screen
indicates the distance remaining before the next service is due.

Example:
1 700 miles remain before the next service is due.
For 7 seconds after the ignition is switched on, the central screen
indicates:


Less than 600 miles (1 000 km) remain before the next service is due


Example:
500 miles remain before the next service is due.
For 7 seconds after the ignition is switched on, the central screen
indicates:

The spanner remains on
on the small
screen to indicate that a service must be
carried out soon.
Maintenance due in
1700 miles or
9 months
1700miles
Maintenance due in
500 miles or
2 months
500miles

= 0
36

Service overdue

For 7 seconds after the ignition is switched on, the spanner fl ashes
to
indicate that the service must be carried out as soon as possible.

Example:
the service is overdue by 300 miles.
For 7 seconds after the ignition is switched on, the central screen indicates:

The spanner remains lit
on the small screen
to indicate that a service should have been
carried out.
The distance remaining may be weighted by the time factor,
depending on the driver's driving habits.
Therefore, the spanner may also come on if you have exceeded
the two year service interval.









Service indicator zero reset

Retrieving the service information

You can access the service information at any time.
This information appears when running through the manual check
procedure.


)
Briefl y press the "CHECK/000"
button.
The service information is displayed for a few seconds on
the instrument panel central screen, then disappears.

Following this operation, if you wish to disconnect the battery, lock
the vehicle and wait at least fi ve minutes for the zero reset to be
registered. After each service, the service indicator must be reset to zero.
The procedure for resetting to zero is as follows:


)
switch off the ignition,

)
press and hold the "CHECK/000"
button,

)
switch on the ignition; the distance recorder display begins a
countdown,

)
when the instrument panel central screen indicates "=0"
, release
the button; the spanner disappears from the small screen.
Interval
exceeded by
300 miles
-300miles

1/
INSTRUMENTS AND CONTROLS












MANUAL CHECK

This function allows you to check the status of the vehicle (reminder
of the alert warnings and of the state of the confi gurable functions -
"activated" or "deactivated") and the service information.


)
With the engine running, to start a manual check, briefl y press the
"CHECK/000"
button on the instrument panel.
If no faults have been detected, "CHECK OK"
appears in the
instrument panel central screen.
If a "minor" fault has been detected, the warning lamp concerned then
"CHECK OK"
appear in the instrument panel central screen. Contact a
PEUGEOT or a qualifi ed workshop.
If a "major" fault has been detected, only the warning lamps concerned
appear in the instrument panel central screen. Have it checked by a
PEUGEOT dealer or a qualifi ed workshop.













DISTANCE RECORDERS

The total and trip distances are displayed for thirty seconds when
the ignition is switched off, when the driver's door is opened and when
the vehicle is locked or unlocked.
Measures the total distance travelled by the vehicle since its fi rst
registration.



Total distance recorder



)
With the ignition on, press and hold this button until zeros appear.



Trip distance recorder

Measures a distance travelled since it was reset to zero by the driver.
4.5
65
4
/min1000mph
CHECK/000
mph 55LIMIT Pause
CHECK/000
13 011 0907
05
0
3010
6
7 5
4
/min1000mph
5
.5
offmph55
CHECK
OK

00.5
16
7
60
6
12
93
55
50
45
40
353025
20
15
1
0
5
38









LIGHTING DIMMER

Permits manual adjustment of the brightness of the instruments and
controls to suit the ambient light level. Only operates when the vehicle
lighting is on, with the exception of the daytime running lamps.

Activation



)
Press the button to change the brightness of the instruments and
controls.

)
When the lighting reaches the minimum setting, release the button,
then press again to increase it.
or


)
When the lighting reaches the maximum setting, release the button,
then press again to reduce it.

)
When the lighting reaches the level of brightness required, release
the button.



Deactivation

When the vehicle lighting is off, or in day mode on vehicles fi tted with
daytime running lamps, pressing the button does not have any effect.

















CLOCK

The analogue clock, located between the central vents of the
dashboard, does not have an adjustment button.
To set the time, refer to the section relating to your multifunction
screen's confi guration menu.
The clock is synchronised with the multifunction screen time; once the
the setting has been confi rmed on the multifunction screen, the hands
will turn to synchronise with the screen, and each time the ignition is
switched on.