2011 LEXUS RX350 lock

425
3-7. Other interior features
3

Interior features
Detach the inner clips of the rear
luggage cover from the back door.
STEP2
nInstalling the rear luggage cover
lEnsure that the luggage cover is in the proper installation position.
Push the clips of the rear luggage cover into the indentions on the back door
until they are locked into place.
lCheck that the rear luggage cover is securely attached.
CAUTION
nWhen the cargo hooks are not in use
To avoid injury, always return the cargo hooks to their stowed positions.

426
3-7. Other interior features
Garage door opener
The garage door opener (HomeLink® Universal Transceiver) is manufactured
under license from HomeLink®.
Programming the HomeLink® (for U.S.A. owners)
The HomeLink® compatible transceiver in your vehicle has 3 buttons
which can be programmed to operate 3 different devices. Refer to the
programming method below appropriate for the device.
Indicator
Buttons
nProgramming the HomeLink®
Point the remote control transmit-
ter for the device 1 to 3 in. (25 to
75 mm) from the HomeLink®
control buttons.
Keep the HomeLink® indicator
light in view while programming.
The garage door opener can be programmed to operate garage doors,
gates, entry doors, door locks, home lighting systems, security systems, and
other devices.
STEP1

429
3-7. Other interior features
3

Interior features
Test the operation of the HomeLink® by pressing the newly pro-
grammed button. Check to see if the gate/device operates cor-
rectly.
Repeat the steps above to program another device for each of
the remaining HomeLink® buttons.
nProgramming other devices
To program other devices such as home security systems, home door
locks or lighting, contact your authorized Lexus dealer for assistance.
nReprogramming a button
The individual HomeLink® buttons cannot be erased but can be
reprogrammed. To reprogram a button, follow the “Reprogramming a
HomeLink® button” instructions.
Operating HomeLink®
Press the appropriate HomeLink® button. The HomeLink® indicator
light should turn on.
The HomeLink® compatible transceiver in your vehicle continues to send a
signal for up to 20 seconds as long as the button is pressed.
Reprogramming a HomeLink® button
Press and hold the desired HomeLink® button. After 20 seconds, the
HomeLink® indicator light will start flashing slowly. Next, while still press-
ing and holding the HomeLink® button, press and hold the button on the
transmitter until the HomeLink® indicator light changes from a slow to a
rapid flash.
STEP5
STEP6

434
3-7. Other interior features
nDeviation calibration
Stop the vehicle.
Press and hold “AUTO”.
A number (1 to 15) appears on the
compass display.
Referring to the map above, press “AUTO” to select the number
of the zone where you are in.
If the direction is displayed for several seconds after adjustment, the
calibration is complete.
nCircling calibration
If “C” appears on the display, drive
the vehicle at 5 mph (8 km/h) or
less in a circle until a direction is
displayed.
If there is not enough space to
drive in a circle, drive around the
block until a direction is displayed.
STEP1
STEP2
STEP3

460
4-3. Do-it-yourself maintenance
Hood
CAUTION
nPre-driving check
Check that the hood is fully closed and locked.
If the hood is not locked properly, it may open while the vehicle is in motion and
cause an accident, which may result in death or serious injury.
Release the lock from the inside of the vehicle to open the hood.
Pull the hood lock release lever.
The hood will pop up slightly.
Pull up the hood catch and lift
the hood.
STEP1
STEP2

467
4-3. Do-it-yourself maintenance
4

Maintenance and care
nAdding engine oil
If the oil level is below or near the
low level mark, add engine oil of
the same type as that already in the
engine.
Make sure to check the oil type and prepare the items needed before
adding oil.
Remove the oil filler cap by turning it counterclockwise.
Add engine oil slowly, checking the dipstick.
Install the oil filler cap by turning it clockwise.
About 1.6 qt. (1.5 L, 1.3 Imp. qt.) is required to raise the oil level from low to full on
the dipstick.
Engine oil
selection→P. 5 9 7
ItemsClean funnel
STEP1
STEP2
STEP3

501
4-3. Do-it-yourself maintenance
4

Maintenance and care
Fuse layout and amperage ratings
nEngine compartment
FuseAmpereCircuit
1RDI FAN NO. 180 AElectric cooling fans
2RR DEF50 ARear window defogger
3AIR SUS50 A
4HTR50 AAir conditioning system
5SPARE30 A
6SPARE40 A
7ABS NO. 230 AAnti-lock brake system
8H-LP CLN30 AHeadlight cleaner
9PBD30 APower back door system
10ST30 AStarter system

502
4-3. Do-it-yourself maintenance
11PD50 A
Daytime running light system, A/F,
H-LP RH HI, H-LP LH LO, H-LP RH
LO, H-LP LH HI, HORN, S-HORN,
multiplex communication system,
multiport fuel injection system/
sequential multiport fuel injection sys-
tem
12ABS NO. 150 AAnti-lock brake system
13EPS60 AElectric power steering system
14ALT140 A
FUEL OPN, DR LOCK, OBD, RR
FOG, S/ROOF, 4WD, INVERTER,
ECU IG1 NO. 1, ECU IG1 NO. 2,
PANEL, GAUGE NO. 1
15AMP130 AAudio system
16EFI MAIN30 A
Multiport fuel injection system/
sequential multiport fuel injection sys-
tem, EFI NO. 1, EFI NO. 2
17AMP230 AAudio system
18IG230 AStarter system, IGN, GAUGE NO. 2,
ECU IG2
19IP JB25 APower door lock system
20STR LOCK20 AStarter system
21RAD NO. 315 A
Meters and gauges lights, instrument
panel lights, navigation system, audio
system, rear seat entertainment sys-
tem
22HAZ15 AEmergency flashers
FuseAmpereCircuit