Page 17 of 62
17
■Changing gears in the M position
Operating the shift lever or paddle shift switches allows a gear to be selected and held,
enabling you to time gear shifts as you please while driving.
Shift the shift lever to M.
The indicator in the meter cluster will
change to display the selected gear.
To u p s h i f t :
Move the shift lever in the “+” direction, or
pull the “+” paddle shift switch toward you.
To d o w n s h i f t :
Move the shift lever in the “-” direction, or
pull the “-” paddle shift switch toward you.
In M mode, the gear will change only when the shift lever or paddle shift switches are oper-
ated. However, when the vehicle speed drops the gear will be automatically downshifted.
Page 18 of 62
18
F-Sport Mode Total Control Switch/
SNOW Mode Switch
Snow mode
For starting or accelerating on snow-covered
roads or other slippery surfaces.
“Sport” mode
Various driving controls are adjusted,
enabling sporty driving.
An indicator comes on in the meter cluster
when in “Sport” or snow mode.
The following modes can be selected to suit driving conditions or your preference.
1
2
To cancel the mode, press the same switch again. When the “ENGINE START STOP”
switch is turned OFF, the mode is automatically deactivated.
Page 19 of 62
19
Parking Brake
To set the parking brake: firmly depress the park-
ing brake pedal.
To release the parking brake: depress the park-
ing brake pedal again.
Tu r n S i g n a l L e v e r
Right turn signal
Left turn signal
CanadaU.S.A.
1
2
To signal a lane change, move the lever partway and hold.
Page 20 of 62
20
Multi-information Display
■Display information
●Trip information
Outside temperature
Driving range
Average fuel consumption
Average fuel consumption after refueling
Current fuel consumption
Average vehicle speed
Gear position display
●Satellite switch mode display
●Intuitive parking assist display
(if equipped)
●Dynamic radar cruise control display
(if equipped)
●Wa r n i n g m e s s a g e s
■Changing the display of trip information
Trip information items can be switched by press-
ing the “DISP” switch.
The multi-information display shows information about your vehicle, including the items
shown below.
Ty p e ATy p e B
■When using the intuitive parking assist or dynamic radar cruise control, the appropriate
display is shown on the screen.
■In the event that a problem is detected in any of the vehicle's systems, a warning message is
shown on the multi-information display.
Page 21 of 62
21
Satellite Switches
The satellite switches can be used to change the
settings of the following items.
●Intuitive parking assist (if equipped)
●Tire pressure warning system initialization
●ID code selection for the tire pressure warning
system
●Pre-collision braking function (if equipped)
■Changing the settings
To cycle through the functions, press either the
left or right selector switch.
To change the settings, press the “ON/OFF”
button.
The satellite switches can be used to change the settings of various functions. Settings
are shown on the multi-information display.
For detailed information on changing the settings, see the Owner’s Manual.
Page 22 of 62
22
Emergency Flasher Switch
Engaging the emergency flasher switch causes all
the turn signal lights to flash.
The emergency flashers can be operated even
when the “ENGINE START STOP” switch is OFF.
Intuitive Parking Assist (If Equipped)
■Turning the system on and off
The system can be turned on and off using the satellite switch. (P. 2 1 )
■Multi-information display
Sensors are used to detect obstacles near the
vehicle. The distance to a detected obstacle is
shown by the number of indicator bars.
Indicates obstacles detected by the corner
sensors
Indicates obstacles detected by the rear cen-
ter sensors
The system uses a screen display and buzzer to inform the driver of obstacles near the
vehicle when parking or driving at low speed.
1
2
Page 23 of 62
23
Cruise Control (If Equipped)
■Setting the speed
Press the “ON-OFF” button.
The system will turn on.
Accelerate or decelerate to the desired
speed, and then push the lever down.
This sets the speed in the cruise control
memory.
■Canceling
To temporarily cancel the cruise control, pull
the lever toward you. To resume the cruise
control, push the lever up.
To turn the system off, press the “ON-OFF”
button.
■Adjusting the speed setting
To increase speed: push the lever up.
To d e c r e a s e s p e e d: push the lever down.
Release the lever when the desired speed is
reached.
Cruise control allows the driver to maintain a constant speed without having to operate the
accelerator pedal.
Use for highway driving or when traveling at a constant speed for long periods of time.
1
2
Page 24 of 62
24
Dynamic Radar Cruise Control (If Equipped)
■Cruise control display
Cruise control settings are shown on the multi-
information display.
Vehicle ahead indicator
Vehicle-to-vehicle distance
Preset speed
■Vehicle-to-vehicle distance control mode
Press the “ON-OFF” button.
Accelerate or decelerate to the desired
speed, and then push the lever down.
Vehicle-to-vehicle distance can be adjusted using
the distance switch.
■Constant speed control mode
Press the “ON-OFF” button.
Push the lever forward and hold for at least
one second.
Accelerate or decelerate to the desired
speed, and then push the lever down.
■Canceling
To temporarily cancel the dynamic radar
cruise control, pull the lever toward you. To
resume the cruise control, push the lever up.
To turn the system off, press the “ON-OFF”
button.
■Adjusting the speed setting
To i n c r e a s e s p e e d: push the lever up.
To decrease speed: push the lever down.
Release the lever when the desired speed is
reached.
Dynamic radar cruise control supplements conventional cruise control with a vehicle-to-
vehicle distance control mode.
1
2
3
1
2
The vehicle-to-vehicle distance control mode maintains the preset cruising speed as long
as no vehicle is detected ahead.
