2011 JEEP GRAND CHEROKEE change time

Do not attempt sharp turns, abrupt maneuvers,
or other unsafe driving actions that can cause
loss of vehicle control. Failure to operate this
vehicle safely may result in a collision, rollover
of the vehicle, and severe or fatal injury. Drive
carefully.Failure to use the driver and passenger seat
belts
provided is a major cause of severe or
fatal injury. In a rollover crash, an unbelted
person is significantly more likely to die than a
person wearing a seat belt. Always buckle up.
IMPORTANT NOTICEALL MATERIAL CONTAINED IN THIS PUBLI-
CATION IS BASED ON THE LATEST INFORMA-
TION AVAILABLE AT TIME OF PUBLICATION
APPROVAL. THE RIGHT IS RESERVED TO
PUBLISH REVISIONS AT ANY TIME.
This Owner’s Manual has been prepared with
the assistance of service and engineering spe-
cialists to acquaint you with the operation and
maintenance of your new vehicle. It is supple-
mented by a Warranty Information Booklet and
various customer-oriented documents. You are
urged to read these publications carefully. Fol-
lowing the instructions and recommendations
in this Owner’s Manual will help assure safe
and enjoyable operation of your vehicle. After you have read the Owner’s Manual, it
should be stored in the vehicle for convenient
reference and remain with the vehicle when
sold.
The manufacturer reserves the right to make
changes in design and specifications, and/or
to make additions to or improvements in its
products without imposing any obligations
upon itself to install them on products previ-
ously manufactured.
The Owner’s Manual illustrates and describes
the features that are standard or available as
extra cost options. Therefore, some of the
equipment and accessories in this publication
may not appear on your vehicle.
NOTE:
Be sure to read the Owner’s Manual first
before driving your vehicle and before at-
taching or installing parts/accessories or
making other modifications to the vehicle.
Rollover Warning Label
5

REMOTE KEYLESS ENTRY (RKE)This system allows you to lock or unlock the
doors or liftgate from distances up to approxi-
mately 33 ft (10 m) using a hand-held Key Fob
with RKE transmitter. The RKE transmitter does
not need to be pointed at the vehicle to activate
the system.
NOTE:
Inserting the Key Fob with RKE transmitter
into the ignition switch disables all buttons
on that RKE transmitter; however, the but-
tons on the remaining RKE transmitters will
continue to work. Driving at speeds 5 mph
(8 km/h) and above disables all RKE trans-
mitter buttons for all RKE transmitters.To Unlock the DoorsPress and release the UNLOCK button on the
RKE transmitter once to unlock the driver’s
door or twice to unlock all doors. The turn
signal lights will flash to acknowledge the un-
lock signal. The illuminated entry system will
also turn on.
Refer to “Passive Entry System” under “Things
To Know Before Starting Your Vehicle” for fur-
ther information.
Remote Key Unlock, Driver Door/All Doors
First Press
This feature lets you program the system to
unlock either the driver’s door or all doors, on
the first press of the UNLOCK button on the
RKE transmitter. To change the current setting,
proceed as follows:
•
For vehicles equipped with the Electronic
Vehicle Information Center (EVIC), refer to
“Electronic Vehicle Information Center (EVIC)/
Personal Settings (Customer-Programmable
Features)” in “Understanding Your Instrument
Panel” for further information.
Flash Lights with Remote Key Lock
This feature will cause the turn signal lights to
flash when the doors are locked or unlocked
with the RKE transmitter. This feature can be
turned on or off. To change the current setting,
proceed as follows:
•
For vehicles equipped with the Electronic
Vehicle Information Center (EVIC), refer to
“Electronic Vehicle Information Center (EVIC)/
Personal Settings (Customer-Programmable
Features)” in “Understanding Your Instrument
Panel” for further information.
Turn Headlights On with Remote Key
Unlock
This feature activates the headlights for up to
90 seconds when the doors are unlocked with
the RKE transmitter. The time for this feature is
programmable on vehicles equipped with the
Electronic Vehicle Information Center (EVIC).
Refer to “Electronic Vehicle Information Center
(EVIC)/Personal Settings (Customer-Program-
mable Features)” in “Understanding Your In-
strument Panel” for further information.
Key Fob with RKE Transmitter
17

WARNING!
•An incorrectly anchored tether strap could
lead to increased head motion and possible
injury to the child. Use only the anchor
positions directly behind the child seat to
secure a child restraint top tether strap.
• Do not use the cargo tie downs located on
the load floor. Improper usage of the tether
can lead to a failure of an infant or child
restraint. The child could be badly injured
or killed. Transporting Pets
Airbags deploying in the front seat could harm
your pet. An unrestrained pet will be thrown
about and possibly injured, or injure a passen-
ger during panic braking or in an accident. Pets
should be restrained in the rear seat in pet
harnesses or pet carriers that are secured by
seat belts.
ENGINE BREAK-IN
RECOMMENDATIONS
A long break-in period is not required for the
engine and drivetrain (transmission and axle) in
your vehicle.
Drive moderately during the first 300 miles
(500 km). After the initial 60 miles (100 km),
speeds up to 50 or 55 mph (80 or 90 km/h) are
desirable.
While cruising, brief full-throttle acceleration
within the limits of local traffic laws, contributes
to a good break-in. Wide-open throttle accel-
eration in low gear can be detrimental and
should be avoided.
The engine oil installed in the engine at the
factory is a high-quality energy conserving type
lubricant. Oil changes should be consistent
with anticipated climate conditions under
which vehicle operations will occur. For the
recommended viscosity and quality grades re-
fer to “Maintenance Procedures” in “Maintain-
ing Your Vehicle”. NON-DETERGENT OR
STRAIGHT MINERAL OILS MUST NEVER BE
USED.
A new engine may consume some oil during its
first few thousand miles (kilometers) of opera-
tion. This should be considered a normal part
of the break-in and not interpreted as an indi-
cation of difficulty.
Additional Requirements For Diesel
Engine — If Equipped
During the first 1500 km avoid heavy loads, e.g.
driving at full throttle. Do not exceed 2/3 of the
maximum permissible engine speed for each
gear. Change gear in good time. Do not shift
down a gear manually in order to brake.
Top Tether Strap Mounting
54

SAFETY TIPS
Transporting Passengers
NEVER TRANSPORT PASSENGERS IN THE
CARGO AREA.
WARNING!
•Do not leave children or animals inside
parked vehicles in hot weather. Interior
heat build-up may cause serious injury or
death.
• It is extremely dangerous to ride in a cargo
area, inside or outside of a vehicle. In a
collision, people riding in these areas are
more likely to be seriously injured or killed.
• Do not allow people to ride in any area of
your vehicle that is not equipped with seats
and seat belts.
• Be sure everyone in your vehicle is in a
seat and using a seat belt properly.
Exhaust Gas
WARNING!
Exhaust gases can injure or kill. They contain
carbon monoxide (CO), which is colorless and
odorless. Breathing it can make you uncon-
scious and can eventually poison you. To
avoid breathing (CO) follow these safety tips:
Do not run the engine in a closed garage or in
confined areas any longer than needed to
move your vehicle in or out of the area.
If it is necessary to sit in a parked vehicle with
the engine running, adjust your heating or
cooling controls to force outside air into the
vehicle. Set the blower at high speed.
If you are required to drive with the trunk/liftgate
open, make sure that all windows are closed
and the climate control BLOWER switch is set
at high speed. DO NOT use the recirculation
mode. The best protection against carbon monoxide
entry into the vehicle body is a properly main-
tained engine exhaust system.
Whenever a change is noticed in the sound of
the exhaust system, when exhaust fumes can
be detected inside the vehicle, or when the
underside or rear of the vehicle is damaged,
have a competent mechanic inspect the com-
plete exhaust system and adjacent body areas
for broken, damaged, deteriorated, or misposi-
tioned parts. Open seams or loose connections
could permit exhaust fumes to seep into the
passenger compartment. In addition, inspect
the exhaust system each time the vehicle is
raised for lubrication or oil change. Replace as
required.
55

Illuminated Vanity MirrorsTo access an illuminated vanity mirror, flip down
one of the visors.
Lift the cover to reveal the mirror. The light will
turn on automatically.
Sun Visor Extension — If EquippedThis feature has a pull out extension on the sun
visor for increased coverage.
BLIND SPOT MONITORING —
IF EQUIPPED
The Blind Spot Monitoring (BSM) system uses
two radar-based sensors, located inside the
rear bumper fascia, to detect Highway licens-
able vehicles (automobiles, trucks, motor-
cycles etc.) that enter the blind spot zones from
the rear/front/side of the vehicle.
When the vehicle is started, the BSM warning
light will be momentarily illuminated in both
outside rear view mirrors to let the driver know
that the system is operational. The BSM system
sensors operate when the vehicle is in anyforward gear or REVERSE and enters stand by
mode when the vehicle is in PARK.
The BSM detection zone covers approximately
one lane on both sides of the vehicle (11 ft or
3.35 m). The zone starts at the outside rear view
mirror and extends approximately 20 ft (6 m) to
the rear of the vehicle. The BSM system moni-
tors the detection zones on both sides of the
vehicle when the vehicle speed has reached
approximately 6 mph (10 km/h) or higher and
will alert the driver of vehicles in these areas.
NOTE:
•
The BSM system does NOT alert the
driver about rapidly approaching vehicles
that are outside the detection zones.
•
The BSM system detection zone DOES
NOT change if your vehicle is towing a
trailer. Therefore, visually verify the adja-
cent lane is clear for both your vehicle and
trailer before making a lane change. If the
trailer or other object (i.e., bicycle, sports
equipment) extends beyond the side of
your vehicle, this may result in the BSM
warning light remaining illuminated the
entire time the vehicle is in a forward gear.Illuminated Vanity Mirror
Rear Detection Zones
69

can be used. Until then, if available, the
previously downloaded phonebook is avail-
able for use.
• Only the phonebook of the currently con-
nected mobile phone is accessible.
• Only the mobile phone’s phonebook is
downloaded. SIM card phonebook is not
part of the mobile phonebook.
• This downloaded phonebook cannot be ed-
ited or deleted on the Uconnect™ Phone.
These can only be edited on the mobile
phone. The changes are transferred and
updated to Uconnect™ Phone on the next
phone connection.
Phonebook Download — Single Entry
If equipped and supported by your phone,
Uconnect™ Phone also allows the user
to download entries one at a time from their
phone via Bluetooth . To use this feature, press
the
button and say “Phonebook Down-
load.” The system prompts “Ready to accept
“V” card entry via Bluetooth …” The system is
now ready to accept a single phonebook entry from your phone using the Bluetooth
Object
Exchange Profile (OBEX). Please see your
phone Owners’ Manual for specific instructions
on how to send these entries from your phone.
NOTE:
• Phone handset must support Bluetooth 
OBEX transfers of phonebook entries to
use this feature.
• Some phones cannot send phonebook
entries if they are already connected to
any system via Bluetooth , and you may
see a message on the phone display that
the Bluetooth link is busy. In this case,
the user must first disconnect or drop the
Bluetooth connection to the Uconnect™
Phone, and then send the address book
entry via Bluetooth . Please see your
phone Owners’ Manual for specific in-
structions on how to drop the Bluetooth 
connection.
• If the phonebook entry is longer than 24
characters, it will only use the first 24
characters. Edit Uconnect™ Phonebook Entries
Editing names in the phonebook is recom-
mended when the vehicle is not in motion.
Automatic downloaded phonebook entries
cannot be deleted or edited.
•
Press the
button to begin.
• After the “Ready” prompt and the following
beep, say “Phonebook Edit”.
• You will then be asked for the name of the
phonebook entry that you wish to edit.
• Next, choose the number designation
(home, work, mobile, or other) that you wish
to edit.
• When prompted, recite the new phone num-
ber for the phonebook entry that you are
editing.
After you are finished editing an entry in the
phonebook, you will be given the opportunity to
edit another entry in the phonebook, call the
number you just edited, or return to the main
menu.
78

Call Termination
To end a call in progress, momentarily press
the
button. Only the active call(s) will be
terminated and if there is a call on hold, it will
become the new active call. If the active call is
terminated by the phone far end, a call on hold
may not become active automatically. This is
cell phone-dependent. To bring the call back
from hold, press and hold the
button until
you hear a single beep.
Redial
• Press the
button to begin.
• After the “Ready” prompt and the following
beep, say “Redial”.
• The Uconnect™ Phone will call the last num-
ber that was dialed from your mobile phone.
NOTE:
This may not be the last number dialed from
the Uconnect™ Phone.
Call Continuation
Call continuation is the progression of a phone
call on the Uconnect™ Phone after the vehicle
ignition key has been switched to OFF. Call continuation functionality available on the ve-
hicle can be any one of three types:
•
After the ignition key is switched to OFF, a
call can continue on the Uconnect™ Phone
either until the call ends, or until a vehicle
specific time expires, or until the vehicle
battery condition dictates cessation of the
call on the Uconnect™ Phone and transfer of
the call to the mobile phone.
• After the ignition key is switched to OFF, a
call can continue on the Uconnect™ Phone
for a certain duration, after which the call is
automatically transferred from the
Uconnect™ Phone to the mobile phone.
• An active call is automatically transferred to
the mobile phone after the ignition key is
switched to OFF.
Uconnect™ Phone Features
Language Selection
To change the language that the Uconnect™
Phone is using:
• Press the
button to begin. •
After the “Ready” prompt and the following
beep, say the name of the language you
wish to switch to (English, Dutch, French,
German, Italian, or Spanish, if so equipped).
• Continue to follow the system prompts to
complete language selection.
After selecting one of the languages, all
prompts and voice commands will be in that
language.
NOTE:
After every Uconnect™ Phone language
change operation, only the language-
specific 32-name phonebook is usable. The
paired phone name is not language-specific
and usable across all languages.
For command translations and alternate com-
mands in supported languages, refer to “Com-
mand Translations”.
Emergency Assistance — If Equipped
If you are in an emergency and the mobile
phone is reachable:
• Pick up the phone and manually dial the
emergency number for your area.
81

numbers, followed by “Send”, is also to be
used for navigating through an automated cus-
tomer service center menu structure, and to
leave a number on a pager.
You can also send stored Uconnect™ Phone-
book entries as tones for fast and easy access
to voice mail and pager entries. To use this
feature, dial the number you wish to call and
then press the
button and say “Send.”
The system will prompt you to enter the name or
number and say the name of the phonebook
entry you wish to send. The Uconnect™ Phone
will then send the corresponding phone num-
ber associated with the phonebook entry, as
tones over the phone.
NOTE:
• You may not hear all of the tones due to
mobile phone network configurations;
this is normal.
• Some paging and voice mail systems
have system time out settings that are too
short and may not allow the use of this
feature. Barge In - Overriding Prompts
The “Voice Command” button can be used
when you wish to skip part of a prompt and
issue your voice command immediately. For
example, if a prompt is asking “Would you like
to pair a phone, clear a
,” you could press
the
button and say, “Pair a Phone” to
select that option without having to listen to the
rest of the voice prompt.
Turning Confirmation Prompts On/Off
Turning confirmation prompts off will stop the
system from confirming your choices (e.g., the
Uconnect™ Phone will not repeat a phone
number before you dial it).
• Press the
button to begin.
• After the “Ready” prompt and the following
beep, say “Setup Confirmations”. The
Uconnect™ Phone will play the current con-
firmation prompt status and you will be given
the choice to change it.
Phone and Network Status Indicators
If available on the radio and/or on a premium
display such as the instrument panel cluster,
and supported by your mobile phone, the Uconnect™ Phone will provide notification to
inform you of your phone and network status
when you are attempting to make a phone call
using Uconnect™ Phone. The status is given
for network signal strength, phone battery
strength, etc.
Dialing Using the Mobile Phone Keypad
You can dial a phone number with your mobile
phone keypad and still use the Uconnect™
Phone (while dialing via the mobile phone
keypad, the user must exercise caution and
take precautionary safety measures). By dial-
ing a number with your paired Bluetooth
mo-
bile phone, the audio will be played through
your vehicle’s audio system. The Uconnect™
Phone will work the same as if you dial the
number using Voice Command.
NOTE:
Certain brands of mobile phones do not
send the dial ring to the Uconnect™ Phone
to play it on the vehicle audio system, so
you will not hear it. Under this situation,
after successfully dialing a number the user
may feel that the call did not go through
83