2011 JEEP GRAND CHEROKEE warning light

NOTE:
You can insert the double-sided emergency
key into the lock cylinders with either side
up.
Removing Key Fob From IgnitionPlace the shift lever in PARK. Turn the Key Fob
to the OFF position and then remove the Key
Fob.
With the Keyless Enter-N-Go feature, the EVIC
will display the ignition switch position “OFF/
ACC/RUN”. Refer to “Electronic Vehicle Infor-
mation Center (EVIC)” in “Understanding Your
Instrument Panel” for further information.NOTE:
•
If you try to remove the Key Fob before
you place the shift lever in PARK, it may
become trapped temporarily in the igni-
tion switch. If this occurs, rotate the key
to the right slightly, then remove the Key
Fob as described. If a malfunction occurs,
the system may trap the key in the igni-
tion switch to warn you that this safety
feature is inoperable. The engine can be
started and stopped, but the Key Fob
cannot be removed until you obtain ser-
vice.
• The power window switches, radio, power
sunroof (if equipped), and power outlets
will remain active for up to 10 minutes
after the ignition switch is turned to the
LOCK position. Opening either front door
will cancel this feature. The time for this
feature is programmable. Refer to “Elec-
tronic Vehicle Information Center (EVIC)/
Personal Settings (Customer-Program-
mable Features)” in “Understanding Your
Instrument Panel” for further information.
WARNING!
• Never leave children alone in a vehicle.
Leaving unattended children in a vehicle is
dangerous for a number of reasons. A child
or others could be seriously or fatally in-
jured. Do not leave the Key Fob in the
ignition or Keyless Enter-N-Go in the ACC
or ON/RUN mode. A child could operate
power windows, other controls, or move the
vehicle.
• Do not leave children or animals inside
parked vehicles in hot weather. Interior
heat build-up may cause serious injury or
death.
CAUTION!
An unlocked car is an invitation to thieves.
Always remove Key Fob from the ignition and
lock all doors when leaving the vehicle unat-
tended.
Emergency Key Removal
13

To Lock the DoorsPress and release the LOCK button on the RKE
transmitter to lock all doors. The turn signal
lights will flash to acknowledge the signal.
Refer to “Passive Entry System” under “Things
To Know Before Starting Your Vehicle” for fur-
ther information.
To Release the Liftgate Flipper
Glass
Press the FLIPPER GLASS/LIFTGATE RE-
LEASE button two times (the second press
within 5 seconds of the first press) to open
liftgate flipper glass.
WARNING!
Driving with the flipper glass open can allow
poisonous exhaust gases into your vehicle.
You and your passengers could be injured by
these fumes. Keep the flipper glass closed
when you are operating the vehicle.
Remote Open Window Feature —
If Equipped
This feature allows you to remotely lower both
front door windows at the same time. To use this
feature, press and release the UNLOCK button
on the RKE transmitter and then immediately
press and hold the UNLOCK button until the
windows lower to the level desired or until they
lower completely.
Programming Additional
Transmitters
Programming Key Fobs or RKE transmitters
may be performed at an authorized dealer.
Transmitter Battery ReplacementThe recommended replacement battery is one
CR2032 battery.
NOTE:
•Perchlorate Material — special handling
may apply. See www.dtsc.ca.gov/
hazardouswaste/perchlorate
• Do not touch the battery terminals that
are on the back housing or the printed
circuit board. 1. Remove the emergency key by sliding the
mechanical latch at the top of the RKE trans-
mitter sideways with your thumb and then pull
the key out with your other hand.
2. Insert the tip of the emergency key or a #2
flat blade screwdriver into the slot and gently
pry the two halves of the RKE transmitter apart.
Make sure not to damage the seal during
removal.Emergency Key Removal
18

WARNING!
Never leave children in a vehicle with the key
in the ignition switch or leave a vehicle with
Keyless Enter-N-Go in the ACC or ON/RUN
position. Occupants, particularly unattended
children, can become entrapped by the win-
dows while operating the power window
switches. Such entrapment may result in se-
rious injury or death.
Auto-Down
Both the driver and front passenger window
switches have an “Auto-Down” feature. Press
the window switch past the first detent, release,
and the window will go down automatically. To
cancel the “Auto-Down” movement, operate
the switch in either the up or down direction
and release the switch.
To open the window part way, press to the first
detent and release it when you want the win-
dow to stop. The power window switches remain active for
10 minutes after the ignition has been turned
OFF. Opening either front door will cancel this
feature.
Auto Up Feature with Anti-Pinch Protection —
Driver and Front Passenger Door Only
Lift the window switch to the second detent,
release, and the window will go up automati-
cally.
To stop the window from going all the way up
during the Auto Up operation, push down on
the switch briefly.
To close the window part way, lift the window
switch to the first detent and release when you
want the window to stop.
NOTE:
If the window runs into any obstacle during
Auto Up it will reverse direction and then go
back down. Remove the obstacle and use
the window switch again to close the win-
dow. Any impact due to rough road condi-
tions may trigger the auto reverse function
unexpectedly during Auto Up. If this hap-pens, pull the switch lightly to the first
detent and hold it to close the window manu-
ally.
WARNING!
There is no anti-pinch protection when the
window is almost closed. Be sure to clear all
objects from the window before closing.
Resetting the Auto Up Feature
Should the Auto Up feature stop working, the
window probably needs to be reset. To reset
Auto Up:
1. Pull the window switch up to close the
window completely and continue to hold the
switch up for an additional two seconds after
the window is closed.
2. Push the window switch down firmly to the
second detent to open the window completely
and continue to hold the switch down for an
additional two seconds after the window is fully
open.
25

Once the liftgate flipper glass has been
opened, connection to the rear window wiper is
interrupted, preventing activation of the rear
wiper blade while the flipper glass is open.
NOTE:
If a malfunction to the liftgate latch should
occur, an emergency liftgate latch release
can be used to open the liftgate. The emer-
gency liftgate latch release can be accessed
through a snap-in cover located on the lift-
gate trim panel.
WARNING!
Driving with the flipper glass open can allow
poisonous exhaust gases into your vehicle.
You and your passengers could be injured by
these fumes. Keep the flipper glass closed
when you are operating the vehicle.
Power Liftgate — If Equipped
The power liftgate may be opened
manually or by pressing the LIFT-
GATE button on the Remote Key-
less Entry (RKE) transmitter. Press
the LIFTGATE button on the RKEtransmitter twice within five seconds, to open
the power liftgate. Once the liftgate is open,
pressing the button twice within five seconds a
second time will close the liftgate.
The power liftgate may also be opened or
closed by pressing the LIFTGATE button lo-
cated on the front overhead console, or closed
by pressing the LIFTGATE button located on
left rear trim, near the liftgate opening. Pressing
the LIFTGATE button located on left rear trim
once will close the liftgate only, this button
cannot be used to open the liftgate.
When the LIFTGATE button on the RKE trans-
mitter is pressed two times, the turn signals will
flash twice to signal that the liftgate is opening
or closing.
NOTE:
In the event of a power malfunction to the
liftgate, an emergency liftgate latch release
can be used to open the liftgate. The emer-
gency liftgate latch release can be accessed
through a snap-in cover located on the lift-
gate trim panel.
WARNING!
During power operation, personal injury or
cargo damage may occur. Ensure the liftgate
travel path is clear. Make sure the liftgate is
closed and latched before driving away.
NOTE:
• If anything obstructs the power liftgate
while it is closing or opening, the liftgate
will automatically reverse to the closed or
open position, provided it meets suffi-
cient resistance.
• There are also pinch sensors attached to
the side of the liftgate. Light pressure
anywhere along these strips will cause
the liftgate to return to the open position.
• The power liftgate must be in the full open
position for rear liftgate close button or
overhead console close button to oper-
ate. If the liftgate is not fully open, press
the Liftgate button on the Key Fob to fully
open the liftgate, and then press it again
to close.
27

Pregnant women should wear the lap part of
the belt across the thighs and as snug across
the hips as possible. Keep the belt low so that
it does not come across the abdomen. That
way the strong bones of the hips will take the
force if there is an accident.
Supplemental Restraint System
(SRS) — Airbags
This vehicle has Advanced Front Airbags for
both the driver and front passenger as a
supplement to the seat belt restraint systems.
The driver’s Advanced Front Airbag is mounted
in the center of the steering wheel. The passen-
ger’s Advanced Front Airbag is mounted in the
instrument panel, above the glove compart-
ment. The words SRS AIRBAG are embossed
on the airbag covers. In addition, the vehicle is
equipped with a driver side knee airbag
mounted in the instrument panel below the
steering column.The Advanced Front Airbags have a multistage
inflator design. This allows the airbag to have
different rates of inflation based on the severity
and type of collision.
This vehicle is equipped with Supplemental
Side Airbag Inflatable Curtains (SABIC) to pro-
tect the driver, front, and rear passengers sit-
ting next to a window. The SABIC airbags, are
located above the side windows and their
covers are also labeled: SRS AIRBAG.This vehicle is equipped with Supplemental
Seat-Mounted Side Airbags (SAB) to provide
enhanced protection for an occupant during a
side impact. The Supplemental Seat-Mounted
Side Airbags are located in the outboard side
of the front seats.
NOTE:
•
Airbag covers may not be obvious in the
interior trim; but they will open during
airbag deployment.
• After any accident, the vehicle should be
taken to an authorized dealer immedi-
ately.
Airbag System Components
Your vehicle may be equipped with the follow-
ing airbag system components:
• Occupant Restraint Controller (ORC)
• Airbag Warning Light
• Steering Wheel and Column
• Instrument Panel
• Supplemental Driver Side Knee Airbag
• Knee Impact BolsterAdvanced Front Airbag and Knee Bolster
Locations
1 — Driver and Passenger Ad-
vanced Front Airbags 3 — Knee
Bolster
2 — Driver Knee Airbag
37

•Driver Advanced Front Airbag
• Passenger Advanced Front Airbag
• Supplemental Seat-Mounted Side Airbags
(SAB)
• Supplemental Side Airbag Inflatable Cur-
tains (SABIC)
• Front and Side Impact Sensors
• Front Seat Belt Pretensioners, Seat Belt
Buckle Switch
• Supplemental Active Head Restraint for
Driver and Front Passenger
Advanced Front Airbag FeaturesThe Advanced Front Airbag system has multi-
stage driver and front passenger airbags. This
system provides output appropriate to the se-
verity and type of collision as determined by
the Occupant Restraint Controller (ORC), which
may receive information from the front impact
sensors.
The first stage inflator is triggered immediately
during an impact that requires airbag deploy- ment. This low output is used in less severe
collisions. A higher energy output is used for
more severe collisions.
WARNING!
•
No objects should be placed over or near
the airbag on the instrument panel, be-
cause any such objects could cause harm if
the vehicle is in a collision severe enough
to cause the airbag to inflate.
• Do not put anything on or around the airbag
covers or attempt to open them manually.
You may damage the airbags and you
could be injured because the airbags may
no longer be functional. The protective cov-
ers for the airbag cushions are designed to
open only when the airbags are inflating.
• Do not drill, cut or tamper with the knee
bolster in any way.
• Do not mount any accessories to the knee
bolster such as alarm lights, stereos, citi-
zen band radios, etc. Supplemental Seat-Mounted Side Airbags
(SAB)
Supplemental Seat-Mounted Side Airbags pro-
vide enhanced protection to help protect an
occupant during a side impact. The Supple-
mental Seat-Mounted Side Airbag is marked
with an airbag label sewn into the outboard
side of the front seats.
When the airbag deploys, it opens the seam
between the front and side of the seat’s trim
cover. Each airbag deploys independently, that
is a left side impact deploys the left airbag only
and a right-side impact deploys only the right
airbag.
Supplemental Seat-Mounted Side Airbag Label
38

WARNING!(Continued)
• Being too close to the Supplemental Side
Airbag Inflatable Curtain (SABIC) and/or
Seat-Mounted Side Airbag (SAB) during
deployment could cause you to be severely
injured or killed.
Airbag Deployment Sensors and
Controls
Occupant Restraint Controller (ORC)
The ORC is part of a regulated safety system
required for this vehicle.
The ORC determines if deployment of the front
and/or side airbags in a frontal or side collision
is required. Based on the impact sensors sig-
nals, a central electronic ORC deploys the
Advanced Front Airbags, Supplemental Driver
Side Knee Airbag, Supplemental Side Airbag
Inflatable Curtain (SABIC), Supplemental Seat-
Mounted Side Airbags (SAB), and front seat
belt pretensioners, as required, depending on
the severity and type of impact. Advanced Front Airbags and knee airbag are
designed to provide additional protection by
supplementing the seat belts in certain frontal
collisions depending on the severity and type
of collision. Advanced Front Airbags are not
expected to reduce the risk of injury in rear, or
side collisions.
The Advanced Front Airbags and knee airbag
will not deploy in all frontal collisions, including
some that may produce substantial vehicle
damage — for example, some pole collisions,
truck underrides, and angle offset collisions.
On the other hand, depending on the type and
location of impact, Advanced Front Airbags
may deploy in crashes with little vehicle front-
end damage but that produce a severe initial
deceleration.
The side airbags will not deploy in all side
collisions. Side airbag deployment will depend
on the severity and type of collision.
Because airbag sensors measure vehicle de-
celeration over time, vehicle speed and dam-
age by themselves are not good indicators of
whether or not an airbag should have de-
ployed.Seat belts are necessary for your protection in
all accidents, and also are needed to help keep
you in position, away from an inflating airbag.
The ORC monitors the readiness of the elec-
tronic parts of the airbag system whenever the
ignition switch is in the START or ON/RUN
position. If the key is in the LOCK position, in
the ACC position, or not in the ignition, the
airbag system is not on and the airbags will not
inflate.
The ORC contains a backup power supply
system that may deploy the airbags even if the
battery loses power or it becomes discon-
nected prior to deployment.
Also, the ORC turns on the Airbag
Warning Light in the instrument
panel for approximately four to
eight seconds for a self-check
when the ignition is first turned to
the ON/RUN position. After the
self-check, the Airbag Warning Light will turn
off. If the ORC detects a malfunction in any part
of the system, it turns on the Airbag Warning
Light, either momentarily or continuously. A
41

single chime will sound if the light comes on
again after initial startup.
It also includes diagnostics that will illuminate
the instrument cluster Airbag Warning Light if a
malfunction is noted that could affect the airbag
system. The diagnostics also record the nature
of the malfunction.
WARNING!
Ignoring the Airbag Warning Light in your
instrument panel could mean you won’t have
the airbags to protect you in a collision. If the
light does not come on, stays on after you
start the vehicle, or if it comes on as you drive,
have an authorized dealer service the airbag
system immediately.
Driver and Passenger Advanced Front
Airbag Inflator Units
The Driver and Passenger Advanced Front
Airbag Inflator Units are located in the center of
the steering wheel and the right side of the
instrument panel. When the ORC detects a
collision requiring the Advanced Front Airbags,
it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the Ad-
vanced Front Airbags. Different airbag inflation
rates are possible, based on the collision type
and severity. The steering wheel hub trim cover
and the upper right side of the instrument panel
separate and fold out of the way as the airbags
inflate to their full size. The airbags fully inflate
in about 50 to 70 milliseconds. This is about half
of the time it takes to blink your eyes. The
airbags then quickly deflate while helping to
restrain the driver and front passenger.
The Advanced Front Airbag gas is vented
through the vent holes in the sides of the
airbag. In this way, the airbags do not interfere
with your control of the vehicle.
Supplemental Driver Side Knee Airbag
Inflator Unit
The driver side knee airbag unit is located in
the instrument panel trim beneath the steering
column. When the ORC detects a collision
requiring the airbag, it signals the inflator units.
A large quantity of non-toxic gas is generated
to inflate the knee airbag. The trim cover sepa-
rates and folds out of the way allowing the
airbag to inflate to the full size. The airbag fully
inflates in about 15 to 20 milliseconds.Supplemental Seat-Mounted Side Airbag
(SAB) Inflator Units
The Supplemental Seat-Mounted Side Airbags
are designed to activate only in certain side
collisions.
The ORC determines if a side collision requires
the side airbags to inflate based on the severity
and type of collision.
Based on the severity and type of collision, the
side airbag inflator on the crash side of the
vehicle may be triggered, releasing a quantity
of non-toxic gas. The inflating side airbag exits
through the seat seam into the space between
the occupant and the door. The side airbags
fully inflate in about 10 milliseconds. The side
airbag moves at a very high speed and with
such a high force, that it could injure you if you
are not seated properly, or if items are posi-
tioned in the area where the side airbag in-
flates. This especially applies to children.
Supplemental Side Airbag Inflatable
Curtain (SABIC) Inflator Units
During collisions where the impact is confined
to a particular area of the side of the vehicle,
the ORC may deploy the SABIC airbags, de-
42