2011 JEEP GRAND CHEROKEE oil temperature

23. Electronic Stability Control (ESC) OFF
Indicator Light — If EquippedThis light indicates the Electronic
Stability Control (ESC) is off.
24. Vehicle Security Light This light will flash rapidly for ap-
proximately 15 seconds when the
vehicle theft alarm is arming. The
light will flash at a slower speed
continuously after the alarm is set.
The security light will also come on
for about three seconds when the ignition is first
turned on.
25. Temperature Gauge
The temperature gauge shows engine coolant
temperature. Any reading within the normal
range indicates that the engine cooling system
is operating satisfactorily.
The gauge pointer will likely indicate a higher
temperature when driving in hot weather, up
mountain grades, or when towing a trailer. It should not be allowed to exceed the upper
limits of the normal operating range.
CAUTION!
Driving with a hot engine cooling system could
damage your vehicle. If the temperature
gauge reads “H” pull over and stop the ve-
hicle. Idle the vehicle with the air conditioner
turned off until the pointer drops back into the
normal range. If the pointer remains on the “H”
and you hear continuous chimes, turn the
engine off immediately, and call an authorized
dealership for service.
WARNING!
A hot engine cooling system is dangerous.
You or others could be badly burned by steam
or boiling coolant. You may want to call an
authorized dealership for service if your ve-
hicle overheats. If you decide to look under
the hood yourself, see “Maintaining Your Ve-
hicle”. Follow the warnings under the Cooling
System Pressure Cap paragraph.26. Rear Fog Light Indicator
This indicator will illuminate when the
rear fog lights are on.
ELECTRONIC VEHICLE
INFORMATION CENTER (EVIC)
The Electronic Vehicle Information Center
(EVIC) features a driver-interactive display that
is located in the instrument cluster.
Electronic Vehicle Information Center (EVIC)
Display
163

Elapsed Time
Shows the total elapsed time of travel since the
last reset when the ignition switch is in the ACC
position. Elapsed time will increment when the
ignition switch is in the ON or START position.
To Reset The Display
Reset will only occur while a resettable function
is being displayed. Press and release the SE-
LECT button once to clear the resettable func-
tion being displayed. To reset all resettable
functions, press and hold the SELECT button
for two seconds. Current display will reset
along with other functions
UnitsPress and release the UP or DOWN button until
“Units” displays highlighted in the EVIC and
press the SELECT button. The EVIC, odometer,
and navigation system (if equipped) can be
changed between English and Metric units of
measure. To make your selection, scroll up or
down until the preferred setting is highlighted,
then press and release the SELECT button until
a check-mark appears next to the setting,
showing that setting has been selected.
Vehicle Info
(Customer Information Features)
Press and release the UP or DOWN button until
“SYSTEM” displays highlighted in the EVIC and
press the SELECT button. Press the UP and
DOWN button to scroll through the available
information displays, then press SELECT to
display anyone of the following choices.
•Coolant Temp
Displays the actual coolant temperature.
• Oil Temperature
Displays the actual oil temperature.
• Oil Pressure
Displays the actual oil pressure.
• Trans Temperature
Displays the actual transmission temperature.
• Engine Hours
Displays the hours of engine operation.
Tire PSI
Press and release the UP or DOWN button until
“Tire PSI” displays highlighted in the EVIC and
press the SELECT button. Press and release the UP/DOWN buttons until one of the following
System Status messages displays in the EVIC:
•
System OK
• System Warnings Displayed (will display all
currently active System Warnings)
• Tire Pressure Monitor System (shows the
current pressure of all four road tires). For
additional information, refer to “Tire Pressure
Monitor System” in “Starting And Operating”.Tire Pressure Display
173

Normal Starting – Diesel EngineObserve the following when the engine is op-
erating.
•All message center lights are off.
• Malfunction Indicator Light (MIL) is off.
• Low Oil Pressure Light is off.
Cold Weather Precautions
Operation in ambient temperature below 32°F
(0°C) may require special considerations. The
following chart suggests these options.
*No. 1 Ultra Low Sulfur Diesel Fuel (ULSD)
should only be used where extended arctic
conditions (-10°F/-23°C) exist. NOTE:
•
Use of Climatized ULSD Diesel Fuel or
Number 1 ULSD Diesel Fuel results in a
noticeable decrease in fuel economy.
• Climatized ULSD Diesel Fuel is a blend of
Number 2 ULSD and Number 1 ULSD
Diesel Fuels, which reduces the tempera-
ture at which wax crystals form in fuel.
NOTE:
This engine requires the use of “Ultra Low
Sulfur Diesel Fuel.” Use of incorrect fuel
could result in exhaust system damage. Re-
fer to “Fuel Requirements – Diesel Engine”
in “Starting and Operating” for further infor-
mation.
Battery Blanket Usage
A battery loses 60% of its cranking power as
the battery temperature decreases to 0°F
(-18°C). For the same decrease in temperature,
the engine requires twice as much power to
crank at the same RPM. The use of battery
blankets will greatly increase starting capability
at low temperatures. Suitable battery blankets
are available from your authorized MOPAR 
dealer. Engine Starting Procedure
WARNING!
Never pour fuel or other flammable liquid into
the air inlet opening in an attempt to start the
vehicle. This could result in a flash fire causing
serious personal injury.
1. The shift lever must be in the NEUTRAL or
PARK position before you can start the engine.
2. Turn the ignition switch to the ON position.
3. Watch for the “Wait To Start Light” in the
instrument cluster. Refer to “Instrument Cluster”
in “Understanding Your Instrument Panel” for
further information. It will glow for two to ten
seconds or more, depending on engine tem-
perature. When the “Wait To Start Light” goes
out, the engine is ready to start.
4. Tip Start Feature
Do not press the accelerator. Use the Fob with
Integrated Key (FOBIK) to briefly turn the igni-
tion switch to the START position and then
release it. The starter motor will continue to run,
and it will automatically disengage when the
engine is running. If the engine fails to start, the
203

starter will disengage automatically in 20 sec-
onds. The starter can be disengaged by turn-
ing the ignition switch to the OFF position, if
required.
5. After the engine starts, allow it to idle for
approximately 30 seconds before driving. This
allows oil to circulate and lubricate the turbo-
charger.
Avoid prolonged idling in ambient tempera-
tures below 0°F (-18°C). Long periods of idling
may be harmful to your engine because com-
bustion chamber temperatures can drop so low
that the fuel may not burn completely. Incom-
plete combustion allows carbon and varnish to
form on piston rings and injector nozzles. Also,
the unburned fuel can enter the crankcase,
diluting the oil and causing rapid wear to the
engine.
Engine Warm Up
Avoid full throttle operation when the engine is
cold. When starting a cold engine, bring the
engine up to operating speed slowly to allow
the oil pressure to stabilize as the engine
warms up.NOTE:
High-speed, no-load running of a cold en-
gine can result in excessive white smoke
and poor engine performance. No-load en-
gine speeds should be kept under 1,200
RPM during the warm-up period, especially
in cold ambient temperature conditions.
If temperatures are below 32°F (0°C), operate
the engine at moderate speeds for five minutes
before full loads are applied.
Engine Idling – In Cold Weather
Avoid prolonged idling in ambient tempera-
tures below 0°F (-18°C). Long periods of idling
may be harmful to your engine because com-
bustion chamber temperatures can drop so low
that the fuel may not burn completely. Incom-
plete combustion allows carbon and varnish to
form on piston rings and injector nozzles. Also,
the unburned fuel can enter the crankcase,
diluting the oil and causing rapid wear to the
engine.
Stopping The Engine
Before turning off your turbo diesel engine,
always allow the engine to return to normal idle
speed and run for several seconds. This as-sures proper lubrication of the turbocharger.
This is particularly necessary after any period
of hard driving.
Idle the engine a few minutes before routine
shutdown. After full load operation, idle the
engine three to five minutes before shutting it
down. This idle period will allow the lubricating
oil and coolant to carry excess heat away from
the combustion chamber, bearings, internal
components, and turbocharger. This is espe-
cially important for turbocharged, charge air
cooled engines.
AUTOMATIC TRANSMISSION
CAUTION!
Damage to the transmission may occur if the
following precautions are not observed:
•
Shift into PARK only after the vehicle has
come to a complete stop.
• Shift into or out of REVERSE only after the
vehicle has come to a complete stop and
the engine is at idle speed.
(Continued)
204

CAUTION!
Do not use chemical flushes in your engine oil
as the chemicals can damage your engine.
Such damage is not covered by the New
Vehicle Limited Warranty.
Engine Oil Selection – ACEA Categories
For countries that use the ACEA European Oil
Categories for Service Fill Oils, use engine oils
that meet the requirements of ACEA C3, and
that are approved to MB 229.31 or MB 229.51.
Engine Oil Viscosity – 3.6L Engine
SAE 5W-30 engine oil is recommended for all
operating temperatures. This engine oil im-
proves low temperature starting and vehicle
fuel economy.
The engine oil filler cap also shows the recom-
mended engine oil viscosity for your vehicle.
For information on engine oil filler cap location,
refer to “Engine Compartment” in “Maintaining
Your Vehicle” for further information. Engine Oil Viscosity – 5.7L Engine
SAE 5W-20 engine oil is recommended for all
operating temperatures. This engine oil im-
proves low temperature starting and vehicle
fuel economy.
The engine oil filler cap also shows the recom-
mended engine oil viscosity for your vehicle.
For information on engine oil filler cap location,
refer to “Engine Compartment” in “Maintaining
Your Vehicle” for further information.
NOTE:
SAE 5W-30 engine oil approved to MB
229.31 or MB 229.51 may be used when SAE
5W-20 engine oil is not available.
Engine Oil – Diesel Engine
Engine Oil Selection
For best performance and maximum protection
under all types of operating conditions, the
manufacturer recommends engine oils that
meet the requirements of Chrysler Material
Standard MS-11106, and that are approved to
Mercedes Benz MB 229.31 or MB 229.51 and
ACEA C3.Engine Oil Viscosity
CAUTION!
Your vehicle is equipped with an advanced
technology Diesel Engine and an emission
device designed to limit Diesel Particulate
Emissions from being released into the atmo-
sphere. The durability of your engine and life
expectancy of this diesel particulate filter
emission device is highly dependent on the
use of the correct engine oil.
SAE 5W-30 Synthetic Low Ash Engine Oil is
recommended for all operating temperatures.
This engine oil improves low temperature start-
ing and vehicle fuel economy.
The engine oil filler cap also shows the recom-
mended engine oil viscosity for your engine.
For information on engine oil filler cap location,
refer to “Engine Compartment” in “Maintaining
Your Vehicle” for further information.
Synthetic Engine OilsYou may use synthetic engine oils provided the
recommended oil quality requirements are met,
275

attention should also be given to hood latching
components to ensure proper function. When
performing other underhood services, the hood
latch, release mechanism and safety catch
should be cleaned and lubricated.
The external lock cylinders should be lubri-
cated twice a year, preferably in the Fall and
Spring. Apply a small amount of a high quality
lubricant, such as MOPARLock Cylinder Lu-
bricant or equivalent directly into the lock cyl-
inder.
Windshield Wiper BladesClean the rubber edges of the wiper blades
and the windshield periodically with a sponge
or soft cloth and a mild nonabrasive cleaner to
remove accumulations of salt or road film.
Operation of the wipers on dry glass for long
periods may cause deterioration of the wiper
blades. Always use washer fluid when using
the wipers to remove salt or dirt from a dry
windshield.
Avoid using the wiper blades to wipe frost or
ice from the windshield. Keep the blade rubber
out of contact with petroleum products such as
engine oil, gasoline, etc. NOTE:
Life expectancy of wiper blades varies de-
pending on geographical area and fre-
quency of use. Poor performance of blades
may be present with chattering, marks, wa-
ter lines or wet spots. If any of these condi-
tions are present, clean the wiper blades or
replace as necessary.
Adding Washer FluidThe fluid reservoir for the windshield washers
and the rear window washer is shared. The fluid
reservoir is located in the engine compartment,
be sure to check the fluid level at regular
intervals. Fill the reservoir with windshield
washer solvent only (not radiator antifreeze).
When refilling the washer fluid reservoir, take
some washer fluid and apply it to a cloth or
towel and wipe clean the wiper blades, this will
help blade performance. To prevent freeze-up
of your windshield washer system in cold
weather, select a solution or mixture that meets
or exceeds the temperature range of your cli-
mate. This rating information can be found on
most washer fluid containers.
WARNING!
Commercially available windshield washer
solvents are flammable. They could ignite and
burn you. Care must be exercised when filling
or working around the washer solution.
Exhaust SystemThe best protection against carbon monoxide
entry into the vehicle body is a properly main-
tained engine exhaust system.
If you notice a change in the sound of the
exhaust system; or if the exhaust fumes can be
detected inside the vehicle; or when the under-
side or rear of the vehicle is damaged; have an
authorized technician inspect the complete ex-
haust system and adjacent body areas for
broken, damaged, deteriorated, or misposi-
tioned parts. Open seams or loose connections
could permit exhaust fumes to seep into the
passenger compartment. In addition, inspect
the exhaust system each time the vehicle is
raised for lubrication or oil change. Replace as
required.
278

•Keep the front of the radiator clean. If your
vehicle is equipped with air conditioning,
keep the front of the condenser clean.
• Do not change the thermostat for Summer or
Winter operation. If replacement is ever nec-
essary, install ONLY the correct type thermo-
stat. Other designs may result in unsatisfac-
tory cooling performance, poor gas mileage,
and increased emissions.
Brake SystemIn order to assure brake system performance,
all brake system components should be peri-
odically inspected. Refer to the “Maintenance
Schedule” for the proper maintenance inter-
vals.
WARNING!
Riding the brakes can lead to brake failure
and possibly an accident. Driving with your
foot resting or riding on the brake pedal can
result in abnormally high brake temperatures,
excessive lining wear, and possible brake
damage. You would not have your full braking
capacity in an emergency. Fluid Level Check – Brake Master Cylinder
The fluid level of the master cylinder should be
checked when performing under the hood ser-
vice, or immediately if the brake system warn-
ing lamp indicates system failure.
The brake master cylinder has a translucent
plastic reservoir. On the outboard side of the
reservoir, there is a “MAX” dot and a “MIN” dot.
The fluid level must be kept within these two
dots. Do not add fluid above the MAX mark,
because leakage may occur at the cap.
With disc brakes, the fluid level can be ex-
pected to fall as the brake linings wear. How-
ever, an unexpected drop in fluid level may be
caused by a leak and a system check should
be conducted.
Refer to “Fluids, Lubricants, and Genuine
Parts” in “Maintaining Your Vehicle” for further
information.
WARNING!
•
Use only manufacturer’s recommended
brake fluid. Refer to “Fluids, Lubricants,
and Genuine Parts” in “Maintaining Your
Vehicle” for further information. Using the
wrong type of brake fluid can severely
damage your brake system and/or impair
its performance. The proper type of brake
fluid for your vehicle is also labeled on the
original factory installed hydraulic master
cylinder reservoir.
• To avoid contamination from foreign matter
or moisture, use only new brake fluid or
fluid that has been in a tightly closed con-
tainer. Keep the master cylinder reservoir
cap secured at all times. Brake fluid in a
open container absorbs moisture from the
air resulting in a lower boiling point. This
may cause it to boil unexpectedly during
hard or prolonged braking, resulting in sud-
den brake failure. This could result in a
accident.
(Continued)
283

CAUTION!
•Using a transmission fluid other than the
manufacturer’s recommended fluid may
cause deterioration in transmission shift
quality and/or torque converter shudder.
Using a transmission fluid other than that
recommended by the manufacturer will re-
sult in more frequent fluid and filter
changes. Refer to “Fluids, Lubricants, and
Genuine Parts” in “Maintaining Your Ve-
hicle” for further information.
• The fluid level is preset at the factory and it
does not require adjustment under normal
operating conditions. If a transmission fluid
leak occurs, visit your authorized dealer
immediately. Severe damage to the trans-
mission may occur. Your authorized dealer
has the proper tools to adjust the fluid level
accurately.
Fluid Level Check – 5.7L Engine
Check the fluid level while the transmission is at
normal operating temperature. This occurs af-
ter at least 15 miles (25 km) of driving. At normal operating temperature the fluid cannot
be held comfortably between the fingertips.
To check the fluid level properly, the following
procedure must be used:
1. Operate the engine at idle speed and nor-
mal operating temperature.
2. The vehicle must be on level ground.
3. Fully apply the parking brake, and press the
brake pedal.
4. Place the shift lever momentarily in each
gear position ending with the shift lever in
PARK.
5. Remove the dipstick, wipe it clean and
reinsert it until seated.
6. Remove the dipstick again, and note the
fluid level on both sides. The fluid level should
be between the “HOT” (upper) reference holes
on the dipstick at normal operating tempera-
ture. The fluid level is only valid if there is a solid
coating of oil on both sides of the dipstick. If the
fluid is low, add as required into the dipstick
tube.
Do not overfill. After adding any quantity
of oil through the oil fill tube, wait a minimum of two minutes for the oil to fully drain into the
transmission before rechecking the fluid level.
NOTE:
If it is necessary to check the transmission
below the operating temperature, the fluid
level should be between the two “COLD”
(lower) holes on the dipstick with the fluid at
approximately 70°F (21°C) (room tempera-
ture). If the fluid level is correctly estab-
lished at room temperature, it should be
between the “HOT” (upper) reference holes
when the transmission reaches 180°F
(82°C). Remember it is best to check the
level at the normal operating temperature.
CAUTION!
Be aware that if the fluid temperature is below
50°F (10°C) it may not register on the dipstick.
Do not add fluid until the temperature is
elevated enough to produce an accurate
reading.
7. Check for leaks. Release parking brake.
To prevent dirt and water from entering the
transmission after checking or replenishing
286