2011 JEEP GRAND CHEROKEE jump start

non-essential electrical devices or increase en-
gine speed (if at idle). If the charging system
light remains on, it means that the vehicle is
experiencing a problem with the charging sys-
tem. Obtain SERVICE IMMEDIATELY. See an
authorized dealer.
If jump starting is required, refer to “Jump
Starting Procedures” in “What To Do In Emer-
gencies”.
•Electronic Throttle Control (ETC) Light
This light informs you of a problem
with the Electronic Throttle Control
(ETC) system. The light will come
on when the ignition is first turned
ON and remain on briefly as a bulb
check. If the light does not come
on during starting, have the system checked by
an authorized dealer.
If a problem is detected, the light will come on
while the engine is running. Cycle the ignition
key when the vehicle has completely stopped
and the shift lever is placed in the PARK
position. The light should turn off.
If the light remains lit with the engine running
your vehicle, will usually be drivable, however, see an authorized dealer for service as soon as
possible. If the light is flashing when the engine
is running, immediate service is required and
you may experience reduced performance, an
elevated/rough idle or engine stall and your
vehicle may require towing.
•
Engine Temperature Warning Light
This light warns of an overheated en-
gine condition. As temperatures rise
and the gauge approaches H,this
indicator will illuminate and a single
chime will sound after reaching a set threshold.
Further overheating will cause the temperature
gauge to pass H,the indicator will continuously
flash and a continuous chime will occur until
the engine is allowed to cool.
If the light turns on while driving, safely pull
over and stop the vehicle. If the A/C system is
on, turn it off. Also, shift the transmission into
NEUTRAL and idle the vehicle. If the tempera-
ture reading does not return to normal, turn the
engine off immediately and call for service.
Refer to “If Your Engine Overheats” in “What To
Do In Emergencies” for more information. •
Transmission Temperature Light
This light indicates that there is
excessive transmission fluid tem-
perature that might occur with se-
vere usage such as trailer towing.
It may also occur when operating
the vehicle in a high torque con-
verter slip condition, such as 4-wheel-drive
operation (e.g., snow plowing, off- road opera-
tion). If this light comes on, stop the vehicle and
run the engine at idle or faster, with the trans-
mission in NEUTRAL until the light goes off.
CAUTION!
Continuous driving with the Transmission
Temperature Indicator illuminated will eventu-
ally cause severe transmission damage or
transmission failure.
170

Controlling The iPodor External
USB Device Using Radio Buttons
To get into the UCI (iPod or external USB
device) mode and access a connected audio
device, either press the “AUX” button on the
radio faceplate or press VR button and say
 USB or Switch to USB . Once in the UCI
mode, audio tracks (if available from audio
device) start playing over the vehicle’s audio
system.
Play ModeWhen switched to UCI mode, the iPod or
external USB device automatically starts Play
mode. In Play mode, the following buttons on
the radio faceplate may be used to control the
iPod or external USB device and display data:
• Use the TUNE control knob to select the next
or previous track.
• Turning it clockwise (forward) by one
click, while playing a track, skips to the
next track or press VR button and say
 Next Track . •
Turning it counterclockwise (backward)
by one click, will jump to the previous
track in the list or press VR button and say
 Previous Track 
• Jump backward in the current track by
pressing and holding the << RWbutton.
Holding the << RWbutton long enough
will jump to the beginning of the current
track.
• Jump forward in the current track by press-
ing and holding the FF>> button.
• A single press backward << RWor forward
FF >> will jump backward or forward re-
spectively, for five seconds.
• Use the << SEEKandSEEK >> buttons to
jump to the previous or next track. Pressing
the SEEK >> button during play mode will
jump to the next track in the list, or can press
VR button and say Next or Previous Track .
• While a track is playing, press the INFO
button to see the associated metadata (art-
ist, track title, album, etc.) for that track.
Pressing the INFObutton again jumps to the
next screen of data for that track. Once all screens have been viewed, the last
INFO
button press will go back to the play mode
screen on the radio.
• Pressing the REPEATbutton will change the
audio device mode to repeat the current
playing track or press the VR button and say
 Repeat ON or Repeat Off .
• Press the SCANbutton to use UCI device
scan mode, which will play the first 10 sec-
onds of each track in the current list and then
forward to the next song. To stop SCAN
mode and start playing the desired track,
when it is playing the track, press the SCAN
button again. During Scan mode, pressing
the << SEEKandSEEK >> buttons will
select the previous and next tracks.
• RND button (available on sales code RES
radio only): Pressing this button toggles be-
tween Shuffle ON and Shuffle OFF modes for
the iPod or external USB device, or press
VR button and say Shuffle ON or 
Shuffle
Off .Ifthe RNDicon is showing on the radio
display, then the shuffle mode is ON.
182

Bluetooth Streaming Audio (BTSA)Music can be streamed from your cellular
phone to the Uconnect™ phone system.
Controlling BTSA using Radio Buttons
To get into the BTSA mode, press either “AUX”
button on the radio or press VR button and say
“Bluetooth Streaming Audio”.
Play Mode
When switched to BTSA mode, some audio
devices can start playing music over the vehi-
cle’s audio system, but some devices require
the music to be initiated on the device first, then
it will get streamed to Uconnect™ phone sys-
tem. Seven devices can be paired to
Uconnect™ phone system, but just one can be
selected and played.
Selecting different Audio Device
1. Press PHONE button to begin.
2. After theReady prompt and the following
beep, say Setup , then Select Audio De-
vices .
3. Say name of the audio device or ask
Uconnect™ phone system to list audio de-
vices. Next Track
Use the SEEK UP button, or press the VR
button on the radio and say “Next Track” to
jump to the next track music on your cellular
phone.
Previous Track
Use the SEEK DOWN button, or press the VR
button on the radio and say “Previous Track” to
jump to the previous track music on your cel-
lular phone.
Browse
Browsing is not available on a BTSA device.
Only the current song that is playing will display
info.
STEERING WHEEL AUDIO
CONTROLS
The remote sound system controls are located
on the rear surface of the steering wheel.
Reach behind the wheel to access the
switches.
The right-hand control is a rocker-type switch
with a pushbutton in the center and controls the
volume and mode of the sound system. Press-
ing the top of the rocker switch will increase the
volume, and pressing the bottom of the rocker
switch will decrease the volume.
Pressing the center button will make the radio
switch between the various modes available
(AM/FM/SAT/CD/HDD/AUX/VES, etc.).
The left-hand control is a rocker-type switch
with a pushbutton in the center. The function of
Remote Sound System Controls
(Back View Of Steering Wheel)
184

•Press the ENGINE START/STOP button a
second time to change the ignition switch to
the RUN position (EVIC displays “IGNITION
MODE RUN”),
• Press the ENGINE START/STOP button a
third time to return the ignition switch to the
OFF position (EVIC displays “IGNITION
MODE OFF”).
Extreme Cold Weather
(Below 20°F or 29°C)
To ensure reliable starting at these tempera-
tures, use of an externally powered electric
engine block heater (available from your autho-
rized dealer) is recommended.
If Engine Fails To Start
WARNING!
• Never pour fuel or other flammable liquids
into the throttle body air inlet opening in an
attempt to start the vehicle. This could
result in a flash fire causing serious per-
sonal injury.
(Continued)
WARNING!(Continued)
• Do not attempt to push or tow your vehicle
to get it started. Vehicles equipped with an
automatic transmission cannot be started
this way. Unburned fuel could enter the
catalytic converter and once the engine has
started, ignite and damage the converter
and vehicle. If the vehicle has a discharged
battery, booster cables may be used to
obtain a start from a booster battery or the
battery in another vehicle. This type of start
can be dangerous if done improperly. Refer
to “Jump Starting” in “What To Do In Emer-
gencies” for further information.
Clearing a Flooded Engine
(Using ENGINE START/STOP Button)
If the engine fails to start after you have fol-
lowed the “Normal Starting” or “Extreme Cold
Weather procedures, it may be flooded. To
clear any excess fuel, press and hold the brake
pedal, push the accelerator pedal all the way to
the floor and hold it, then press and release the
ENGINE START/STOP button once. The starter
motor will engage automatically, run for 10 sec- onds, and then disengage. Once this occurs,
release the accelerator pedal and the brake
pedal, wait 10 to 15 seconds, then repeat the
“Normal Starting” procedure.
Clearing A Flooded Engine
(Using Fob With Integrated Key)
If the engine fails to start after you have fol-
lowed the “Normal Starting” or “Extreme Cold
Weather” procedures, it may be flooded. To
clear any excess fuel, push the accelerator
pedal all the way to the floor and hold it. Then,
turn the ignition switch to the START position
and release it as soon as the starter engages.
The starter motor will disengage automatically
in 10 seconds. Once this occurs, release the
accelerator pedal, turn the ignition switch to the
LOCK position, wait 10 to 15 seconds, then
repeat the “Normal Starting” procedure.
CAUTION!
To prevent damage to the starter, wait 10 to
15 seconds before trying again.
After StartingThe idle speed is controlled automatically and it
will decrease as the engine warms up.
202

6
WHAT TO DO IN EMERGENCIES
•HAZARD WARNING FLASHERS ................. 258
• IF YOUR ENGINE OVERHEATS .................. 258
• JACKING AND TIRE CHANGING ................. 259
• Jack Location .......................... 259
• Spare Tire Stowage ....................... 259
• Preparations for Jacking .................... 259
• Jacking Instructions ...................... 260
• JUMP-STARTING .......................... 262
• Preparations for Jump-Start .................. 262
• Jump-Starting Procedure ................... 263
• TOW EYES .............................. 264
• TOWING A DISABLED VEHICLE ................. 265
• Towing Without the Ignition Key Fob ............ 266
• Four-Wheel Drive Vehicles ................... 266
257

12. Securely store the road wheel and jack in
the cargo area.
13. Have the aluminum road wheel and tire
repaired as soon as possible and properly
secure the spare tire, jack and tool kit.
WARNING!
A loose tire or jack, thrown forward in a
collision or hard stop could endanger the
occupants of the vehicle. Always stow the jack
parts and the spare tire in the places provided.
JUMP-STARTINGIf your vehicle has a discharged battery it can
be jump-started using a set of jumper cables
and a battery in another vehicle or by using a
portable battery booster pack. Jump-starting
can be dangerous if done improperly so please
follow the procedures in this section carefully.
NOTE:
When using a portable battery booster pack
follow the manufacturer’s operating instruc-
tions and precautions.
CAUTION!
Do not use a portable battery booster pack or
any other booster source with a system volt-
age greater than 12 Volts or damage to the
battery, starter motor, alternator or electrical
system may occur.
WARNING!
Do not attempt jump-starting if the battery is
frozen. It could rupture or explode and cause
personal injury.
Preparations for Jump-StartThe battery in your vehicle is located under the
passenger’s front seat. There are remote loca-
tions located under the hood to assist in jump-
starting.
Stowed Spare
Remote Battery Posts
1 — Remote Positive(+) Post
(covered with protective cap)
2 — Remote Negative (-) Post
262

WARNING!
•Take care to avoid the radiator cooling fan
whenever the hood is raised. It can start
anytime the ignition switch is on. You can
be injured by moving fan blades.
• Remove any metal jewelry such as watch
bands or bracelets that might make an
inadvertent electrical contact. You could be
seriously injured.
• Batteries contain sulfuric acid that can burn
your skin or eyes and generate hydrogen
gas which is flammable and explosive.
Keep open flames or sparks away from the
battery.
1. Set the parking brake, shift the automatic
transmission into PARK and turn the ignition to
LOCK.
2. Turn off the heater, radio, and all unneces-
sary electrical accessories.
3. Remove the protective cover over the re-
mote positive (+)battery post. Pull upward on
the cover to remove it. 4. If using another vehicle to jump-start the
battery, park the vehicle within the jumper
cables reach, set the parking brake and make
sure the ignition is OFF.
WARNING!
Do not allow vehicles to touch each other as
this could establish a ground connection and
personal injury could result.
Jump-Starting Procedure
WARNING!
Failure to follow this procedure could result in
personal injury or property damage due to
battery explosion.
CAUTION!
Failure to follow these procedures could result
in damage to the charging system of the
booster vehicle or the discharged vehicle.
1. Connect the positive
(+)end of the jumper
cable to the remote positive (+)post of the
discharged vehicle.
2. Connect the opposite end of the positive (+)
jumper cable to the positive (+)post of the
booster battery.
3. Connect the negative end (-)of the jumper
cable to the negative (-)post of the booster
battery.
4. Connect the opposite end of the negative (-)
jumper cable to the remote negative (-)post of
the vehicle with the discharged battery.
WARNING!
Do not connect the cable to the negative post
(-) of the discharged battery. The resulting
electrical spark could cause the battery to
explode and could result in personal injury.
5. Start the engine in the vehicle that has the
booster battery, let the engine idle a few min-
utes, and then start the engine in the vehicle
with the discharged battery.
263

Once the engine is started, remove the jumper
cables in the reverse sequence:
6. Disconnect the negative(-)jumper cable
from the remote negative (-)post of the dis-
charged vehicle.
7. Disconnect the negative end (-)of the
jumper cable from the negative (-)post of the
booster battery.
8. Disconnect the opposite end of the positive
(+) jumper cable from the positive (+)post of
the booster battery.
9. Disconnect the positive (+)end of the
jumper cable from the remote positive (+)post
of the discharged vehicle.
10. Reinstall the protective cover over the re-
mote positive (+)battery post of the discharged
vehicle. If frequent jump-starting is required to start your
vehicle you should have the battery and charg-
ing system inspected at your authorized dealer.
CAUTION!
Accessories that can be plugged into the
vehicle power outlets draw power from the
vehicle’s battery, even when not in use (i.e.,
cellular phones, etc.). Eventually, if plugged in
long enough, the vehicle’s battery will dis-
charge sufficiently to degrade battery life
and/or prevent the engine from starting.
TOW EYESYour vehicle is equipped with tow eyes, which
are mounted in the front and the rear.
CAUTION!
Tow eyes are for emergency use only, to
rescue a vehicle stranded off road. Do not use
tow eyes for tow truck hookup or highway
towing. You could damage your vehicle. Tow
straps are recommended when towing the
vehicle; chains may cause vehicle damage.
WARNING!
Stand clear of vehicles when pulling with tow
eyes. Tow straps and chains may break, caus-
ing serious injury.
264