2011 INFINITI QX56 brake fluid

BRAKE WARNING LAMPBRC-123
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
Component Function CheckINFOID:0000000006222651
1.CHECK BRAKE WARNING LAMP FUNCTION (1)
Check that brake warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Proceed to diagnosis procedure. Refer to BRC-123, "
Diagnosis Procedure".
2.CHECK BRAKE WARNING LAMP FUNCTION (2)
Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.
NOTE:
Brake warning lamp turns ON when parking brake is operated (when parking brake switch is ON).
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check parking brake switch system. Refer to BRC-117, "
Diagnosis Procedure".
3.CHECK BRAKE WARNING LAMP FUNCTION (3)
Check that brake warning lamp in combination meter turns ON/OFF when brake fluid level switch is operated
while brake fluid level in reservoir tank is with the specified level.
NOTE:
Brake warning lamp turns ON when brake fluid is less than the specified level (when brake fluid level switch is
ON).
Is the inspection result normal?
YES >> INSPECTION END
NO >> Check brake fluid level switch system. Refer to BRC-103, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006222652
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and elec tric unit (control unit) power supply and ground circuit.
Refer to BRC-113, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.PERFORM THE SELF-DIAGNOSIS
With CONSULT-III.
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES >> Check the DTC. Refer to BRC-51, "DTC Index".
NO >> GO TO 3.
3.CHECK BRAKE WARNING LAMP SIGNAL
With CONSULT-III.
1. Select “ABS”, “DATA MONITOR” and “EBD WARN LAMP” according to this order.
2. Turn the ignition switch OFF.
3. Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON and then changes to “Off”.
CAUTION:
Never start engine.
Is the inspection result normal?
Revision: 2010 May2011 QX56

EXCESSIVE OPERATION FREQUENCYBRC-127
< SYMPTOM DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SYMPTOM DIAGNOSIS
EXCESSIVE OPERATION FREQUENCY
DescriptionINFOID:0000000006222657
VDC function, TCS function, ABS functi on, EBD function, hill start assist function and brake limited slip differ-
ential (BLSD) function operates in excessive operation frequency.
Diagnosis ProcedureINFOID:0000000006222658
1.CHECK BRAKING FORCE
Check brake force using a brake tester.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check brake system.
2.CHECK FRONT AND REAR AXLE
Check that there is no excessive looseness in front and rear axle.
 Front axle: Refer to FA X - 7 , "
Inspection" (2WD), FAX-16, "Inspection" (4WD).
 Rear axle: Refer to RAX-5, "
Inspection"
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.CHECK WHEEL SENSOR
Check wheel sensor.
 Check installation and damage of wheel sensor.
 Check connection of wheel sensor harness connector.
 Check terminal of wheel sensor harness connector.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace wheel sensor.  Front wheel sensor: Refer to BRC-134, "
FRONT WHEEL SENSOR : Removal and Installation".
 Rear wheel sensor: Refer to BRC-135, "
REAR WHEEL SENSOR : Removal and Installation".
4.CHECK WARNING LAMP TURNS OFF
Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn OFF approx. 1 second after
key switch is turned ON and stay in OFF status during driving.
CAUTION:
Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake
fluid is less than the specified level (brake fluid level switch is ON).
Is the inspection result normal?
YES >> Normal
NO >> Perform self-diagnosis for “ABS” with CONSULT-III.
Revision: 2010 May2011 QX56

BRC-128
< SYMPTOM DIAGNOSIS >[WITH VDC]
UNEXPECTED BRAKE PEDAL REACTION
UNEXPECTED BRAKE PEDAL REACTION
DescriptionINFOID:0000000006222659
A malfunction of brake pedal feel (height or ot
hers) is detected when brake pedal is depressed.
Diagnosis ProcedureINFOID:0000000006222660
1.CHECK FRONT AND REAR AXLE
Check that there is no excessive looseness in front and rear axle.
 Front axle: Refer to FAX-7, "
Inspection" (2WD), FAX-16, "Inspection" (4WD).
 Rear axle: Refer to RAX-5, "
Inspection"
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK DISC ROTOR
Check disc rotor runout.
 Front: Refer to BR-16, "
DISC ROTOR : Inspection and Adjustment".
 Rear: Refer to BR-18, "
DISC ROTOR : Inspection and Adjustment".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Refinish or replace disc rotor.  Front: Refer to BR-16, "
DISC ROTOR : Inspection and Adjustment".
 Rear: Refer to BR-18, "
DISC ROTOR : Inspection and Adjustment".
3.CHECK BRAKE FLUID LEACKAGE
Check fluid leakage.
 Front: Refer to BR-24, "
FRONT : Inspection".
 Rear: Refer to BR-26, "
REAR : Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace error-detected parts.
4.CHECK BRAKE PEDAL
Check each item of brake pedal. Refer to BR-7, "
Inspection and Adjustment".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Adjust each item of brake pedal. Refer to BR-7, "
Inspection and Adjustment".
5.CHECK BRAKING FORCE
Check brake force using a brake tester.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Check each components of brake system.
6.CHECK BRAKE PERFORMANCE
Disconnect ABS actuator and electric unit (control unit) connector so that ABS does not operate. Check that
brake force is normal in this condition. Connect harness connectors after checking.
Is the inspection result normal?
YES >> Normal
NO >> Check each components of brake system.
Revision: 2010 May2011 QX56

BRC-130
< SYMPTOM DIAGNOSIS >[WITH VDC]
DOES NOT OPERATE
DOES NOT OPERATE
DescriptionINFOID:0000000006222663
VDC function, TCS function, ABS functi
on, EBD function, hill start assist function and brake limited slip differ-
ential (BLSD) function does not operate.
Diagnosis ProcedureINFOID:0000000006222664
CAUTION:
 VDC function, ABS function and EBD function never operate when the vehicle speed is 10 km/h (6.2
MPH) or less.
 TCS function, hill start assist fu nction and brake limited slip diffe rential (BLSD) function operates
when the vehicle speed is 0 km/h (0 MPH) (the vehicle is in stop status).
 VDC function and TCS function never operate wh en VDC OFF switch is operated (when VDC OFF
indicator lamp turns ON).
1.CHECK ABS WARNING LAMP
Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn ON and turn OFF approx. 1
second after key switch is turned ON. Check that ABS warning lamp, brake warning lamp and VDC warning
lamp and stay in OFF status during driving.
CAUTION:
Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake
fluid is less than the specified level (brake fluid level switch is ON).
Is the inspection result normal?
YES >> Normal
NO >> Perform self-diagnosis for “ABS” with CONSULT-III.
Revision: 2010 May2011 QX56

NORMAL OPERATING CONDITIONBRC-133
< SYMPTOM DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000006222669
Symptom Result
Brake pedal slightly vibrates and operation sound (motor sound and sound from suspen-
sion) occurs when VDC function, TCS function, ABS function, EBD function, hill start assist
function and brake limited slip differential (BLSD) function operates. This is not a malfunction, The symptom
occurs VDC function
, TCS function, ABS
function, EBD function, hill start assist
function and brake limited slip differential
(BLSD) function that are normally operat-
ed.
Brake stopping distance may become longer than models without ABS function depending
on the road conditions, when
ABS function is operated on slip pery road like rough road,
gravel road or snowy road.
Brake pedal vibrates and operation sound occurs during sudden acceleration and corner-
ing, when VDC function, TCS function, hill start assist function and brake limited slip differ-
ential (BLSD) function is operated.
Brake pedal vibrates and motor sound from the engine room occurs, when the engine starts
or the vehicle starts just after starting the engine This is not a malfunction. The symptom
occurs during the brake fluid accumula-
tion in the accumulator and operational
check of the ABS actuator and electric
unit (control unit).
Acceleration may be felt insufficient depending on the road conditions. This is not a malfunction. The symptom occurs TCS function that puts the highest
priority to obtain the optimum traction
(stability).
TCS may operate momentarily, while driving on a road where friction coefficient varies, or
when downshifting or fully depressing accelerator pedal
ABS warning lamp and VDC warning lamp may turn ON, when the vehicle is on a rotating
turntable or is given a strong shaking or large vibrations on a ship while the engine is run-
ning.
In this case, restart the engine on a nor-
mal road. If the normal condition is re-
stored, there is no malfunction. In that
case, erase self-diagnosis result memory
for “ABS” with CONSULT-III.
VDC warning lamp may turn ON and VDC function, TCS function, hill start assist function
and brake limited slip differential (BLSD) function may not normally operate, when driving
on a special road the is extremely slanted (bank in a circuit course).
A malfunction in yaw rate/side/decel G sensor system may be detected when the vehicle
sharply turns during a spin turn, acceleration turn or drift driving while VDC function and
TCS function are OFF (VDC OFF switch is pressed and VDC OFF indicator lamp is in ON
status).
The vehicle speed does not increase, when the accelerator pedal is depressed while the
vehicle is on a 2-wheel chassis dynamometer for speedometer check.
This is not malfunction. (When checking
the vehicle on a chassis dynamometer,
operate VDC OFF switch so that TCS
function is OFF.)
The VDC warning lamp, ABS warn ing lamp and brake warning lamp turn ON and DTC
“C118E” may be detected in self-diagnosis resu lt of “ABS” when the brake pedal is exces-
sively operated, such as air bleeding. This is not a system malfunction because
this occurs due to the temporary de-
crease in accumulator fluid pressure. The
system returns to no
rmal condition when
the accumulator fluid pressure reaches
the specified pressure with the ignition
switch ON and the VDC warning lamp,
ABS warning lamp, a nd brake warning
lamp turn OFF. After these steps, ABS
self-diagnosis results are erased.
VDC OFF indicator lamp turns ON and TCS function is not operate when 4WD mode is “4L”.
(Models with 4WD system) This is not a malfunction. When the 4WD
mode becomes “4L” state, the TCS func-
tion is disabled. This function is enabled
when the 4WD mode becomes “AUTO”
or “4H”.
Revision: 2010 May2011 QX56

COMPONENT PARTSBRC-143
< SYSTEM DESCRIPTION > [BRAKE ASSIST (WITH PREVIEW FUNCTION)]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Component DescriptionINFOID:0000000006248457
× : Applicable
13. Steering angle sensor
Refer to BRC-10, "
Component Parts
Location"
14. ADAS control unit
Refer to DAS-13, "
Component Parts
Location"
A. Back side of engine room (RH) B. Front bumper (center) C. Upper side of brake pedal
D. Under side of instrument lower driver
panel
Component Function
Description
Vehicle-to-vehicle distance control mode
Conventional (fixed speed) cruise control mode Intelligent Brake Assist (IBA)
Brake Assist (with preview function)
ADAS control unit ×××× ADAS control unit calculates a target distance between vehicles
and a target speed, based on signals received from each sensor
and switch to transmit an engine torque command value to ECM
and a brake fluid pressure cont rol signal to ABS actuator and
electric unit (control unit) via CAN communication
 ADAS control unit transmits buzzer output signal to combination
meter via CAN communication
ICC sensor ×××× ICC sensor detects light reflected from a vehicle ahead by irra-
diating laser forward and calculates a distance from the vehicle
ahead and a relative speed, based on the detected signal
 ICC sensor transmits the presence/absence of vehicle ahead and the distance from the vehicle to ADAS control unit via ITS
communication
ECM ×××× ECM transmits the accelerator pedal position signal, ICC brake
switch signal, stop lamp switch signal, ICC steering switch sig-
nal, etc. to ADAS control unit via CAN communication
 ECM controls the electric throttle control actuator based on the engine torque demand received from the ADAS control unit via
CAN communication
ABS actuator and electric unit
(control unit) ×××× ABS actuator and electric unit (c
ontrol unit) transmits the vehicle
speed signal (wheel speed), stop lamp signal and VDC/TCS/
ABS system operation condition to ADAS control unit via CAN
communication
 ABS actuator and electric unit (c ontrol unit) controls the brake,
based on a brake fluid pressure control signal received from the
ADAS control unit via CAN communication
BCM ×BCM transmits the front wiper request signal to ADAS control unit
via CAN communication
TCM ××TCM transmits the signal related to A/T control to ADAS control
unit via CAN communication
Revision: 2010 May2011 QX56

BRC-150
< SYSTEM DESCRIPTION >[INTELLIGENT BRAKE ASSIST]
COMPONENT PARTS
Component Description
INFOID:0000000006248459
× : Applicable
13. Steering angle sensor
Refer to BRC-10, "
Component Parts
Location"
14. ADAS control unit
Refer to DAS-13, "
Component Parts
Location"
A. Back side of engine room (RH) B. Front bumper (center) C. Upper side of brake pedal
D. Under side of inst rument lower driver
panel
Component Function
Description
Vehicle-to-vehicle distance control mode
Conventional (fixed speed) cruise control mode Intelligent Brake Assist (IBA)
Brake Assist (with preview function)
ADAS control unit ×××× ADAS control unit calculates a target distance between vehicles
and a target speed, based on signals received from each sensor
and switch to transmit an engine torque command value to ECM
and a brake fluid pres sure control signal to ABS actuator and
electric unit (control unit) via CAN communication
 ADAS control unit transmits buzzer output signal to combination
meter via CAN communication
ICC sensor ×××× ICC sensor detects light reflected from a vehicle ahead by irra-
diating laser forward and calculates a distance from the vehicle
ahead and a relative speed, based on the detected signal
 ICC sensor transmits the presence/absence of vehicle ahead and the distance from the vehicle to ADAS control unit via ITS
communication
ECM ×××× ECM transmits the accelerator pedal position signal, ICC brake
switch signal, stop lamp switch signal, ICC steering switch sig-
nal, etc. to ADAS control unit via CAN communication
 ECM controls the electric throttle control actuator based on the engine torque demand received from the ADAS control unit via
CAN communication
ABS actuator and electric unit
(control unit) ×××× ABS actuator and electric unit (control unit) transmits the vehicle
speed signal (wheel speed), stop lamp signal and VDC/TCS/
ABS system operation condition to ADAS control unit via CAN
communication
 ABS actuator and electric unit (control unit) controls the brake, based on a brake fluid pressure control signal received from the
ADAS control unit via CAN communication
BCM ×BCM transmits the front wiper request signal to ADAS control unit
via CAN communication
TCM ××TCM transmits the signal related to A/T control to ADAS control
unit via CAN communication
Revision: 2010 May2011 QX56

CCS-10
< SYSTEM DESCRIPTION >[ICC]
COMPONENT PARTS
Component Description
INFOID:0000000006224266
× : Applicable
13. Steering angle sensor
Refer to BRC-10, "
Component Parts
Location"
14. ADAS control unit
Refer to DAS-13, "
Component Parts
Location"
A. Back side of engine room (RH) B. Front bumper (center) C. Upper side of brake pedal
D. Under side of inst rument lower driver
panel
Component Function
Description
Vehicle-to-vehicle distance control mode
Conventional (fixed speed) cruise control mode Intelligent Brake Assist (IBA)
Brake Assist (with preview function)
ADAS control unit ×××× ADAS control unit calculates a target distance between vehicles
and a target speed, based on signals received from each sensor
and switch to transmit an engine torque command value to ECM
and a brake fluid pres sure control signal to ABS actuator and
electric unit (control unit) via CAN communication
 ADAS control unit transmits buzzer output signal to combination
meter via CAN communication
ICC sensor ×××× ICC sensor detects light reflected from a vehicle ahead by irra-
diating laser forward and calculates a distance from the vehicle
ahead and a relative speed, based on the detected signal
 ICC sensor transmits the presence/absence of vehicle ahead and the distance from the vehicle to ADAS control unit via ITS
communication
ECM ×××× ECM transmits the accelerator pedal position signal, ICC brake
switch signal, stop lamp switch signal, ICC steering switch sig-
nal, etc. to ADAS control unit via CAN communication
 ECM controls the electric throttle control actuator based on the engine torque demand received from the ADAS control unit via
CAN communication
ABS actuator and electric unit
(control unit) ×××× ABS actuator and electric unit (control unit) transmits the vehicle
speed signal (wheel speed), stop lamp signal and VDC/TCS/
ABS system operation condition to ADAS control unit via CAN
communication
 ABS actuator and electric unit (control unit) controls the brake, based on a brake fluid pressure control signal received from the
ADAS control unit via CAN communication
BCM ×BCM transmits the front wiper request signal to ADAS control unit
via CAN communication
TCM ××TCM transmits the signal related to A/T control to ADAS control
unit via CAN communication
Revision: 2010 May2011 QX56