2011 INFINITI QX56 engine oil

EC-68
< SYSTEM DESCRIPTION >[VK56VD]
DIAGNOSIS SYSTEM (ECM)
VEHICLE SPEED km/h or mph The vehicle speed computed from the vehicle
speed signal sent from TCM is displayed.
IDL A/V LEARN YET/CMPLT  Displays the condition of Idle Air Volume Learning
YET: Idle air volume learning has not been per-
formed yet.
CMPLT: Idle air volume learning has already been
performed successfully.
TRVL AFTER MIL km or mile  Distance traveled while MIL is activated.
SNOW MODE SW ON/OFF  Indicates [ON/OFF] condition from the snow mode
switch signal.
ENG OIL TEMP °C or °F  The engine oil temperature (determined by the sig-
nal voltage of the engine oil temperature sensor) is
displayed.
MAIN SW ON/OFF  Indicates [ON/OFF] condition from MAIN switch
signal.
CANCEL SW ON/OFF  Indicates [ON/OFF] condition from CANCEL
switch signal.
RESUME/ACC SW ON/OFF  Indicates [ON/OFF] condition from RESUME/AC-
CELERATE switch signal.
SET SW ON/OFF  Indicates [ON/OFF] condition from SET/COAST
switch signal.
BRAKE SW1 ON/OFF  Indicates [ON/OFF] condition from ASCD brake
switch signal.
BRAKE SW2 ON/OFF  Indicates [ON/OFF] condition of stop lamp switch
signal.
DIST SW ON/OFF  Indicates [ON/OFF] condition from DISTANCE
switch signal.
CRUISE LAMP ON/OFF  Indicates [ON/OFF] condition of CRUISE indicator
determined by the ECM according to the input sig-
nals.
AC EVA TEMP °C or °F  Indicates A/C evaporator temperature sent from A/
C auto amp.
AC EVA TARGET °C or °F  Indicates target A/C evaporator temperature sent
from A/C auto amp.
FAN DUTY %  Indicates a command value for cooling fan. The
value is calculated by ECM based on input signals.
ALT DUTY %  Indicates the duty ratio of the power generation
command value. The ratio is calculated by ECM
based on the battery current sensor signal.
BAT CUR SEN mV  The signal voltage of battery current sensor is dis-
played.
A/F ADJ-B1
— Indicates the correction of a factor stored in ECM.
The factor is calculated from the difference be-
tween the target air-fuel ratio stored in ECM and
the air-fuel ratio calculated from A/F sensor 1 sig-
nal.
A/F ADJ-B2
P/N POSI SW ON/OFF
 Indicates [ON/OFF] condition from the park/neutral
position (PNP) signal.
INT/A TEMP SE °C or °F  The intake air temperature (determined by the sig-
nal voltage of the intake air temperature sensor) is
indicated.
AC PRESS SEN V  The signal voltage from the refrigerant pressure
sensor is displayed.
FUEL PRES SEN MPa  Indicates the fuel rail pressure computed by ECM
according to the input signals
Monitored item Unit Description Remarks
Revision: 2010 May2011 QX56

EC-70
< SYSTEM DESCRIPTION >[VK56VD]
DIAGNOSIS SYSTEM (ECM)
*: The item is indicated, but not used.
NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
ACTIVE TEST MODE
Test Item
ECM TEMP 1
°C or °F  Displays a temperature calculated from a signal of
ECM temperature sensor 1.
ECM TEMP 2 °C or °F  Displays a temperature calculated from a signal of
ECM temperature sensor 2.
FUEL PUMP DUTY %  The control condition of the fuel pump control mod-
ule (FPCM) (determined by ECM according to the
input signals) is indicated.
Monitored item Unit Description Remarks
TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
VENT CON-
TROL/V  Ignition switch: ON (Engine
stopped)
 Turn solenoid valve ON and OFF with the CONSULT-III and listen
to operating sound. Solenoid valve makes an operating
sound.
 Harness and connectors
 Solenoid valve
ENG COOLANT
TEMP  Engine: Return to the original
non-standard condition
 Change the engine coolant tem- perature using CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.  Harness and connectors
 Engine coolant temperature sen-
sor
 Fuel injector
FUEL INJEC-
TION  Engine: Return to the original
non-standard condition
 Change the amount of fuel injec- tion using CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.
 Harness and connectors
 Fuel injector
 Air fuel ratio (A/F) sensor 1
FUEL/T TEMP
SEN  Change the fuel tank temperature using CONSULT-III.
PURG VOL
CONT/V  Engine: After warming up, run en-
gine at 1,500 rpm.
 Change the EVAP canister purge
volume control solenoid valve
opening percent using CON-
SULT-III. Engine speed changes according to
the opening percent.
 Harness and connectors
 Solenoid valve
FAN DUTY CON-
TROL* Ignition switch: ON
 Change duty ratio using CON-
SULT-III. Cooling fan speed changes.  Harness and connectors
 Cooling fan motor
 Cooling fan relay
 Cooling fan control module
 IPDM E/R
ALTERNATOR
DUTY Engine: Idle
 Change duty ratio using CON-
SULT-III. Battery voltage changes.  Harness and connectors
 IPDM E/R
Alternator
POWER BAL-
ANCE  Engine: After warming up, idle the
engine.
 A/C switch OFF
 Selector lever: P or N
 Cut off each injector signal one at a time using CONSULT-III. Engine runs rough or stops.
 Harness and connectors
 Compression
 Fuel injector
 Power transistor
Spark plug
 Ignition coil
IGNITION TIM-
ING  Engine: Return to the original
non-standard condition
 Timing light: Set
 Retard the ignition timing using
CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.
 Perform Idle Air Volume Learning.
Revision: 2010 May2011 QX56

EC-74
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
INT/V SOL (B2) Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle 0 - 2%
2,000 rpm Approx. 0 - 50%
AIR COND RLY  Engine: After warming up, idle
the engine A/C switch: OFF OFF
A/C switch: ON
(Compressor operates)
ON
VENT CONT/V  Ignition switch: ON OFF
THRTL RELAY  Ignition switch: ON ON
A/F S1 HTR (B1)  Engine: After warming up, idle the engine
(More than 140 seconds after starting engine) 4 - 100%
A/F S1 HTR (B2)  Engine: After warming up, idle the engine
(More than 140 seconds after starting engine) 4 - 100%
HO2S2 HTR (B1)  Engine speed: Below 3,600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load ON
 Engine speed: Above 3,600 rpm OFF
HO2S2 HTR (B2)  Engine speed: Below 3,600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load ON
 Engine speed: Above 3,600 rpm OFF
ALT DUTY SIG  Power generation voltage variable control: Operating ON
 Power generation voltage variable control: Not operating OFF
I/P PULLY SPD  Vehicle speed: More than 20 km/h (12 MPH) Almost the same speed as
the tachometer indication
VEHICLE SPEED  Turn drive wheels and compare CONSULT-III value with the speedometer in-
dication. Almost the same speed as
the speedometer indication
IDL A/V LEARN  Engine: Running Idle air volume learning has not been per-
formed yet.
YET
Idle air volume learning has already been
performed successfully. CMPLT
TRVL AFTER MIL  Ignition switch: ON Vehicle has traveled after MIL has illumi-
nated.0 - 65,535 km
(0 - 40,7
23 miles)
SNOW MODE SW  Ignition switch: ON Snow mode switch: ON ON
Snow mode switch: OFF OFF
ENG OIL TEMP  Engine: After warming up More than 70 °C (158 °F)
MAIN SW  Ignition switch: ON MAIN switch: Pressed ON
MAIN switch: Released OFF
CANCEL SW  Ignition switch: ON CANCEL switch: Pressed ON
CANCEL switch: Released OFF
RESUME/ACC SW  Ignition switch: ON RESUME/ACCELERATE switch:
Pressed
ON
RESUME/ACCELERATE switch: Re-
leased OFF
SET SW  Ignition switch: ON SET/COAST switch: Pressed ON
SET/COAST switch: Released OFF
BRAKE SW1
(ASCD/ICC brake
switch)  Ignition switch: ON
Brake pedal: Fully released ON
Brake pedal: Slightly depressed OFF
Monitor Item Condition Values/Status
Revision: 2010 May2011 QX56

ECM
EC-81
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
23
(V) 45
(L/O) Low fuel pressure sensor Input [Engine is running]
 Warm-up condition
 Idle speed
2.4 - 3.6 V
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm 2.4 - 3.6 V
25
(LG) —Sensor ground
[Mass air flow sensor/ Intake air
temperature sensor] —— —
27
(P) 45
(L/O) Sensor power supply
(Power steering pressure sen-
sor/ Low fuel pressure sensor/
Electrically-controlled cooling
fan coupling)
— [Ignition switch: ON] 5 V
28
(SB) 40
(W/L) Sensor power supply
(Fuel rail pressure sensor/En-
gine oil pressure sensor)
— [Ignition switch: ON] 5 V
29
(W) 35
(—) Knock sensor (bank 1) Input [Engine is running]
 Idle speed
2.0 V*
1
31
(V/W) 40
(W/L) Fuel rail pressure sensor Input [Engine is running]
 Warm-up condition
 Idle speed
0.98 - 1.2 V
[Engine is running]
 Warm-up condition
 Revving engine from idle to 4,000 rpm quickly 1.1 - 2.9 V
32
(R) 40
(W/L) Engine coolant temperature
sensor
Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
coolant temperature.
33
(W) 35
(—) Knock sensor (bank 2) Input [Engine is running]
 Idle speed
2.0 V*
1
35
(—) —Sensor ground
(Knock sensor)
—— —
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JPBIA3357ZZ
JPBIA3358ZZ
Revision: 2010 May2011 QX56

EC-82
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
37
(V) 175
(B) Cooling fan speed Input [Ignition switch: ON]
 Engine stopped
5 V
[Engine is running]
 Idle speed
 After warm-up condition BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Idle speed
 Before warm-up condition BATTERY VOLTAGE
(11 - 14 V)
39
(P/B) 45
(L/O) Power steering pressure sensor Input [Engine is running]
 Steering wheel: Being turned
0.5 - 4.5 V
[Engine is running]
 Steering wheel: Not being turned 0.4 - 0.8 V
40
(W/L) —Sensor ground
(Fuel rail pressure sensor/En-
gine coolant temperature sen-
sor/Engine oil temperature
sensor) —— —
42
(L/Y) 40
(W/L) Engine oil temperature sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
oil temperature.
45
(L/O) —Sensor ground
(Power steering pressure sen-
sor/ Low fuel pressure sensor/
Electrically-controlled cooling
fan coupling) —— —
46
(SB) 175
(B) Fuel injector driver power supply Input [Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: OFF] 1.5 V
47
(G) 175
(B) Heated oxygen sensor 2 heater
(bank 1)
Input[Engine is running]
 Engine speed: Below 3,600 rpm af-
ter the following conditions are met
- Engine: after warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load 10 V
[Ignition switch: ON]
 Engine: Stopped
[Engine is running]
 Engine speed: Above 3,600 rpm BATTERY VOLTAGE
(11 - 14 V)
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JPBIA3332ZZ
JPBIA3733ZZ
JMBIA0037GB
Revision: 2010 May2011 QX56

EC-94
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
DTC No. Detected items Engine operating condition in fail-safe mode
U0113
U1003
U1024 Can communication circuit VVEL actuator
motor relay is turned off, and VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P0011
P0021 Intake valve timing control The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
P0087 FRP control system  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P0088 Engine speed is limited.
P008A Low fuel pressure control
system Engine torque is limited.
P0090 FRP control system  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P0102
P0103 Mass air flow sensor circuit Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0117
P0118 Engine coolant tempera-
ture sensor circuit
Engine coolant temperature will be determined by ECM based on the following condition.
CONSULT-III displays the engine coolant temperature decided by ECM.
Condition Engine coolant temperature decided
(CONSULT-III display)
Just as ignition switch is turned ON
or START 40
°C (104 °F)
Approx. 4 minutes or more after
engine starting 80
°C (176 °F)
Except as shown above 40 - 80 °C (104 - 176 °F)
(Depends on the time)
When the fail-safe system for engine coolant temperature sensor is activated, the cooling
fan operates while engine is running.
P0122
P0123
P0222
P0223
P2135 Throttle position sensor The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
Therefore, the acceleration will be poor.
P0190 FRP sensor  Engine speed is limited.
 High pressure fuel pump is activated at maximum discharge pressure.
P0201
P0202
P0203
P0204
P0205
P0206
P0207
P0208 Injector  Engine torque is limited.
 Fuel injection shut-off of malfunction cylinder.
 Mixture ratio feedback control does not function.
 Idle engine speed is increased.
P0500 Vehicle speed sensor The cooling fan operates (Highest) while engine is running.
P0524 Engine oil pressure The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0605 ECM (When ECM calculation function is malfunctioning:)
ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
ECM deactivates ASCD operation.
P0607 ECM VVEL actuator motor relay is
turned off, and VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
Revision: 2010 May2011 QX56

ECM
EC-97
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Priority Detected items (DTC)
1  U0101 CAN communication line  U0113 U1003 CAN communication line
 U1001 CAN communication line
 U1024 VVEL CAN communication line
 P006A P0101 P0102 P0103 Mass air flow sensor
 P010A Manifold absolute pressure sensor
 P0112 P0113 P0127 Intake air temperature sensor
 P0116 P0117 P0118 P0125 Engine coolant temperature sensor
 P0122 P0123 P0222 P0223 P1225 P1226 P2135 Throttle position sensor
 P0128 Thermostat function
 P0181 P0182 P0183 Fuel tank temperature sensor
 P0196 P0197 P0198 Engine oil temperature sensor
 P0327 P0328 P0332 P0333 Knock sensor
 P0335 Crankshaft position sensor
 P0340 P0345 Camshaft position sensor
 P0460 P0461 P0462 P0463 Fuel level sensor
 P0500 Vehicle speed sensor
 P0527 Cooling fan speed sensor
 P0605 P0607 P0611 P062B ECM
 P0643 Sensor power supply
 P0700 TCM
 P0705 P0850 Transmission range switch
 P1089 P1092 P1608 VVEL control shaft position sensor
 P1197 Out of gas*
 P1220 Fuel pump control module (FPCM)
 P1421 P1423 P1424 Cold start control
 P1550 P1551 P1552 P1553 P1554 Battery current sensor
 P1556 P1557 Battery temperature sensor
 P1606 P1607 VVEL control module
 P1610 - P1615 NATS
 P2122 P2123 P2127 P2128 P2138 Accelerator pedal position sensor
 P2539 P2541 P2542 Low fuel pressure sensor
Revision: 2010 May2011 QX56

EC-98
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
NOTE:
*: If “P1197” is displayed with other DTC in priority 1, perform trouble diagnosis for “P1197” first.
DTC IndexINFOID:0000000006217733
×
:Applicable —: Not applicable
2  P0031 P0032 P0051 P0052 Air fuel ratio (A/F) sensor 1 heater
 P0037 P0038 P0057 P0058 Heated oxygen sensor 2 heater
 P0075 P0081 Intake valve timing control solenoid valve
 P0130 P0131 P0132 P0133 P0150 P0151 P0152 P015 3 P2A00 P2A03 Air fuel ratio (A/F) sensor 1
 P0137 P0138 P0139 P0157 P0158 P0159 Heated oxygen sensor 2
 P0190 - P0193 FRP sensor
 P0441 EVAP control system purge flow monitoring
 P0443 P0444 P0445 EVAP canister purge volume control solenoid valve
 P0447 P0448 EVAP canister vent control valve
 P0451 P0452 P0453 EVAP control system pressure sensor
 P0550 Power steering pressure sensor
 P0603 ECM power supply
 P0710 P0717 P0720 P0729 P0730 P0731 P0732 P0733 P0734 P0735 P0740 P0744 P0745 P0750 P0775 P0780 P0795 P1730 P1734 P2713 P2722 P2731 P2807 A/T related sensors, solenoid valves and switches
 P1087 P1088 VVEL system
 P1090 P1093 VVEL actuator motor
 P1091 VVEL actuat or motor relay
 P1217 Engine over temperature (OVERHEAT)
 P1650 Starter motor relay 2
 P1651 Starter motor relay
 P2101 Electric throttle control function
 P2118 Throttle control motor
 P1805 Brake switch
 P2100 P2103 Throttle control motor relay
 P2101 Electric throttle control function
3  P0011 P0021 Intake valve timing control  P0087, P0088, P0090 FRP control system
 P008A Low fuel pressure control system
 P008B Low fuel pressure control system
 P0171 P0172 P0174 P0175 Fuel injection system function
 P0201 - P0208 Injector
 P0300 - P0308 Misfire
 P0420 P0430 Three way catalyst function
 P0456 EVAP control system (VERY SMALL LEAK)
 P0506 P0507 Idle speed control system
 P050E Cold start control
 P0524 Engine oil pressure
 P1148 P1168 Closed loop control
 P1212 TCS communication line
 P1421 Cold start control
 P1564 ASCD steering switch / ICC steering switch
 P1652 Starter motor system communication
 P2119 Electric throttle control actuator
 P1564 ASCD steering switch / ICC steering switch
 P1568 ICC command value
 P1572 ASCD brake switch / ICC brake switch
 P1574 ASCD vehicle speed sensor / ICC vehicle speed sensor
Priority Detected items (DTC)
DTC*1
Items
(CONSULT-III screen terms) SRT code Trip MIL
Reference
page
CONSULT-III
GST*
2ECM*3
U0101 0101 LOST COMM (TCM) — 1 ×EC-171
U0113 0113 CAN COMM CIRCUIT — 1 ×EC-173
U1001
1001*4CAN COMM CIRCUIT — 1 or 2 — EC-172
U1003 1003 CAN COMM CIRCUIT — 2 — EC-173
Revision: 2010 May2011 QX56